I N S T A L L A T I O N EH1512 Series Enclosures EH1512 Enclosure with EM1512 Mount C3453M-B (4/09)
Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Models . . . . . . . . . . . . . . . . . . . . . . . . . . .
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
Description The EH1512 Series indoor/outdoor enclosures are designed for use with small- to medium-sized analog and IP cameras. They will accommodate both fixed and variable focal length lenses (with or without auto-iris operation). They can be wall mounted using either Pelco’s EM1512 (feedthrough wall mount) or any light to medium duty mount. The tethered, removable enclosure lid provides easy access during installation and when camera and lens adjustments are necessary.
PACKAGE CONTENTS NOTE: A metric Allen wrench (5 mm) is required for installation but is not included. A Phillips screwdriver, flat head screwdriver, or 1/4-inch nut driver is needed for the EH1512-1 and EH1512-3 only. The Allen wrench is needed to open and close the enclosure and to secure the enclosure to all mounts. It is also needed to secure the pan/tilt (swivel head) on the EM1512 mount.
Installation INSTALLING THE CAMERA AND MOUNT To install the enclosure, camera, and lens: 1. Use a 5-mm Allen wrench (not supplied) to loosen the three screws on the enclosure base. 2. Lift up and remove the lid (refer to Figure 2). Hang the lid from the front of the enclosure base by the lanyards. NOTE: The gasket can come loose when the lid is removed. Be sure to properly reseat the gasket, if necessary. Figure 2.
3. Remove the camera sled from the enclosure rail (refer to Figure 3). a. Squeeze the two plastic tabs (located near the front window) that hold the camera sled in place. b. Pull up and slide the sled forward. c. Remove the sled. Figure 3. Removing the Sled 4. Remove the parts bag. This includes the screws, split washers, glands, and nuts. 5.
7. If you are using the EM1512 mount, attach the mount to the wall as follows: a. Using the mount as a template, mark and drill holes in the mounting surface. b. Pull the video and power cables from the wall through the mount. If wiring with conduit, use a step drill to drill a 0.875 inches (2.22 cm) hole in one of the three knockout locations for 1/2-inch conduit. (Knockouts are indicated on the side and bottom of the mount arm.) Refer to Table B on page 10 to determine the size of the power wire needed.
120 VAC MODEL WIRING 24 VAC CAMERA OUTPUT HIGH 24 VAC CAMERA OUTPUT LOW HI LOW 24 VAC AC IN AC OUT HI NT HI NT INPUT, AC HIGH INPUT, AC LOW (NEUTRAL) 0 - GROUND BOSS ZIP TIE HERE 120 VAC CAMERA OUTPUT, LOW (NEUTRAL) 120 VAC OUTPUT, HIGH 24 VAC MODEL WIRING INPUT, AC LOW (NEUTRAL) INPUT, AC HIGH LOW HI AC AC CAMERA CAMERA OUTPUT, AC LOW (NEUTRAL) CAMERA OUTPUT, AC HIGH 230 VAC MODEL WIRING 24 VAC CAMERA OUTPUT LOW 24 VAC CAMERA OUTPUT HIGH HI LOW 24 VAC AC IN AC OUT HI NT HI NT INPUT, AC HIGH INPU
INSTALLING THE SUN SHROUD The optional sun shroud fits over the top of the EH1512 enclosure. Perform the following steps to install the sun shroud. 1. Position the front of the sun shroud above the front of the enclosure. 2. Press the sun shroud down and against the enclosure until the sun shroud snaps into place. Table A. Allowable Cable Diameter Gland Cable Diameter PG9 0.181-inch to 0.312-inch PG11 0.230-inch to 0.395-inch NOTE: Conduit must be used if the cable diameter is greater than 0.
Table C. 24 VAC Wiring Distances Wire Gauge Total VA 20 AWG (0.5 mm2) 18 AWG (1.0 mm2) 16 AWG (1.5 mm2) 14 AWG (2.
Specifications • EH1512-3 • EH1512-1MT • EH1512-2MT • EH1512-3MT • EH1512-1MTS • EH1512-2MTS • EH1512-3MTS • Maximum Power Consumption Capacity EH1512-2 Enclosure Power Consumption* • • 12 W 25 W • 12 W • 12 W 25 W 25 W Sun Shroud EH1512-1 EM1512 Feed Through Wall Mount • Heater/Blower EH1512MT 230VAC with 24VAC Camera Power • 24VAC with 24VAC Camera Power EH1512 120VAC with 24VAC Camera Power Model Number Basic Enclosure MODELS • • • • • • • • • • • • 12 W • •
Unit Weight EH1512 EH1512MT EH1512-1 EH1512-2 EH1512-3 EH1512-1MT EH1512-2MT EH1512-3MT EH1512-1MTS EH1512-2MTS EH1512-3MTS 2.50 lb (1.13 kg) 3.13 lb (1.42 kg) 3.25 lb (1.47 kg) 2.56 lb (1.16 kg) 3.25 lb (1.47 kg) 3.88 lb (1.76 kg) 3.19 lb (1.45 kg) 3.88 lb (1.76 kg) 4.76 lb (2.16 kg) 4.07 lb (1.85 kg) 4.76 lb (2.16 kg) Shipping Weight EH1512 EH1512MT EH1512-1 EH1512-2 EH1512-3 EH1512-1MT EH1512-2MT EH1512-3MT EH1512-1MTS EH1512-2MTS EH1512-3MTS 4 lb (1.81 kg) 5 lb (2.27 kg) 5 lb (2.27 kg) 4 lb (1.
RECOMMENDED CAMERAS AND LENSES Cameras C10CH-6, C10CH-6X, C10CH-7X, C10DN-6, C10DN-6X, C10DN-7X, CCC1390H-6, CCC1390H-6X, IP3701H-2, IP3701H-2X, IXS0C, IXS0DN, IX10C, IX10DN, IXE20C, IXE20DN, IX30C, IX30DN Lenses 13VD2.8-12, 13VD3-8, 13VD5-40, 13VD5-50, 13VDIR2.8-11, 13VDIR3-8.5, 13VDIR7.5-50 NOTE: These lenses are for use with all cameras except Pelco IP cameras with Sarix™ technology. Refer to the specific camera specification sheet for information on recommended lenses.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
www.pelco.com Pelco, Inc.
