I N S T A L L A T I O N ® EPS5000-300 External Redundant Power Supply For Endura Modules C1631M-A (9/05)
Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . .
C1631M-A (9/05)
Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC Rules.
Before You Begin Please familiarize yourself with the parts list before installing the unit. PARTS LIST Qty Description 1 EPS5000-300 2 USA standard power cord 2 European standard power cord 2 UK standard power cord 2 Over-molded G-power cables 4 Screws with washers, 10-32 x 0.750-inch, Phillips, pan head 1 1 Rail Kit 2 Rails 2 Brackets 2 Plates 4 Screws, 6-32 x 0.375-inch, Phillips, pan head 4 Screws, 10-32 x 0.750-inch, Phillips, pan head with washers 8 Screws, 8-32 x 0.
USA STANDARD POWER CORD (110 VAC) 2 EA. SHIPPING BOX EPS5000-300 EUROPEAN STANDARD POWER CORD (230 VAC) 2 EA. SUPPORT RAIL KIT RACK MOUNT SCREW WITH WASHER 10-32 X 0.750 4 EA. INSTALLATION MANUAL OVER-MOLDED G-POWER CABLES 2 EA. UK STANDARD POWER CORD (250 VAC) 2 EA. Figure 1. Package Components RAIL 2 EA. BRACKET 2 EA. PLATE 2 EA. SUPPORT RAIL KIT SHOWN ACTUAL SIZE PHILLIPS PAN HEAD SCREW 6-32 x 0.375 4 EA. PHILLIPS PAN HEAD SCREW WITH WASHER 8-32 x 0.625 8 EA.
Description The EPS5000-300 external redundant power supply, which is 1 rack unit (RU) high, has dual 300 W power supplies that slide into a tray. The external power supply can be mounted into a 19-inch, EIA-standard rack. The EPS5000-300 can be used in the following ways: • Provide redundant power to two fully populated RK5000PS-5U • Provide redundant power to one fully populated RK5000PS-5U The EPS5000-300 has a relay output connector that is directly wired to the power and is a normally closed (N.C.
Installation MOUNTING AN EPS5000-300 The power supply, which is 1 RU high, can provide redundant power to one or two fully populated RK5000PS-5U. To mount the power supply, follow these steps and refer to Figure 5. 1. Insert the EPS5000-300 into the rack. 2. Secure the EPS5000-300 to the rack with four of the supplied 10-32 x 0.750-inch screws and washers. 3. Connect each power supply to the RK5000PS-5U using the supplied over-molded cables.
ATTACHING RAILS TO AN EPS5000-300 The rails give the EPS5000-300 more support for rack mounting, especially in deeper racks. To attach the rails, follow these steps and refer to Figure 7. 1. Secure the two brackets to the back of the EPS5000-300 with the four supplied 6-32 x 0.375-inch screws. 2. Place the rails on the sides of the EPS5000-300 to a desired length. 3. Secure the rails and plates to the brackets using the eight supplied 8-32 x 0.625-inch screws and washers. 4.
EPS5000-300 POWER CORD POWER CORD OVER-MOLDED CABLE RK5000PS-5U OVER-MOLDED CABLE RK5000PS-5U Figure 8.
Service REPLACING A POWER SUPPLY You can easily replace either of the two power supplies in the EPS5000-300 with a replacemnet (EPSPWR-300). You will know if there is a problem with a power supply because the blue Pelco badge on the front panel will turn off. Before replacing a power supply, check the fuse. It can be replaced easily with the supplied spare. If the fuse is not the problem, then follow these steps and refer to Figure 9 to replace the power supply. 1.
Specifications ELECTRICAL Input Voltage 100-240 VAC Output Voltage 12 VDC Power Consumption 600 watts, 308 BTU/H Fuse 4 amps MECHANICAL Rack Units 1 Construction Aluminum Finish Black GENERAL Operating Temperature 32˚ to 122˚F (0˚ to 50˚C) Operating Humidity 80% maximum relative humidity, noncondensing Dimensions 1.73” H x 17.40” W x 12.00” D (4.39 x 44.20 x 30.48 cm) Mounting Fits 19-inch, EIA-standard rack Unit Weight 16.5 lb (7.
C1631M-A (9/05)
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex ® Series products (multiplexers, server, and keyboard).
® Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.