I N S TA L L AT I O N / O P E R AT I O N 200 Series Flat Panel LCD Monitors C2925M-B (12/06)
Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Description . . . . . . . . . . . . . . . . . . . . . . . . . . .
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules.
Description The 200 Series LCD monitors provide high resolution display of VGA signals. These 17- and 19-inch monitors use a color, thin film transfer (TFT) active matrix 1280 x 1024 LCD panel that automatically adapts to the appropriate input resolution.
Installation The monitor can be placed on any flat surface (desk or table), or it can be rack mounted or wall mounted. NOTE: Only use a recommended rack mount kit, such as PMCL-RM17, PMCL-RM19, or PMCL-WM. To rack-mount the monitor, follow the instructions supplied with the rack mount kit. Refer to manual C2220M for rack mount kit instructions or C2219M for wall mount kit instructions.
Operation FRONT PANEL CONTROLS CH Figure 2. Front Panel Controls 1. Automatically selects the input signal. 2. Decreases the value of a selected menu item or opens the Volume menu and decreases volume. 3. Increases the value of a selected menu item or opens the Volume menu and increases volume. 4. Moves the highlighter downward through a menu. 5. Moves the highlighter upward through a menu. 6. Button accesses the pop-up menu and is also used to select a highlighted menu item. 7.
OSD CONTROL MENUS Unless otherwise noted, the menus are the same for the PMCL217 and PMCL219. To use the menus: 1. Press the menu button to access the Main menu. 2. Use the up and down arrow buttons to highlight a selection. 3. Press the menu button to select an item. 4. Use the left and right arrow buttons to adjust the setting on a selected item. MAIN MENU MAIN MENU VGA IN: 1280x1024 H.SYNC: -48.3KHz V.SYNC: -60.
DISPLAY ADJUST MENU DISPLAY ADJUST 050 080 050 058 000 V-POSITION H-POSITION PITCH PHASE SHARPNESS AUTO TUNING RECALL RETURN Figure 4. Display Adjust Menu Display Adjust Menu Field Definitions V-Position: Moves the screen image up or down. H-Position: Moves the screen image left or right. Pitch: Adjusts image distortion appearing as vertical bars or noise on the screen. Phase: Adjusts image distortion appearing as horizontal noise on the screen. Sharpness: Adjusts the picture softer or sharper.
OSD ADJUST MENU OSD ADJUST OSD H-POS OSD V-POS OSD TIMER OSD TRANSPARENCY RECALL RETURN 049 049 020 054 Figure 6. OSD Adjust Menu OSD Adjust Menu Field Definitions OSD H-Pos: Moves the OSD menu box left or right. OSD V-Pos: Moves the OSD menu box up or down. OSD Timer: Sets the number of seconds the menu remains on the screen. The maximum setting is 104. OSD Transparency: Adjusts the transparency of the OSD menu box. Recall: Restores this submenu’s settings to the factory defaults.
Maintenance If the quality of the picture is poor and cannot be improved by making adjustments on the front control panel, inspect all system connections and cable runs. WARNING: To reduce the risk of electrical shock, do not remove the cover or back of the monitor. No user-serviceable parts are inside. Refer servicing to qualified personnel, or contact the Pelco Customer Service Department for assistance, 1-800-289-9100.
Supported Input Modes C2925M-B (1/07) Mode Resolution H Freq (kHz) V Freq (Hz) 0 720 x 350 31.469 70.087 1 640 x 480 31.469 59.940 2 640 x 480 35.000 66.667 3 640 x 480 37.861 72.809 4 640 x 480 37.500 75.000 5 720 x 400 31.469 70.087 6 800 x 600 35.156 56.250 7 800 x 600 37.879 60.317 8 800 x 600 48.077 72.188 9 800 x 600 46.875 75.000 10 832 x 624 49.750 74.500 11 1024 x 768 48.363 60.004 12 1024 x 768 56.476 70.069 13 1024 x 768 58.038 71.
Specifications MODELS PMCL217 PMCL219 17-inch (432 mm) active TFT LCD monitor 19-inch (483 mm) active TFT LCD monitor GENERAL LCD Panel Pixel Array Panel Aspect Ratio Viewing Area PMCL217 PMCL219 Pixel Pitch PMCL217 PMCL219 Brightness PMCL217 PMCL219 Contrast Ratio Backlight Type Panel Lamp Life Viewing Angle (H/V) PMCL217 PMCL219 Tilt Display Colors PMCL217 PMCL219 Response Time Speakers Front Panel Controls Indicators 1280 X 1024, 75 Hz 5:4 VGA 338 x 270 mm 376 x 301 mm 0.264 x 0.264 mm 0.294 x 0.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FR/FT/FS Series fiber optic products and TW3000 Series unshielded twisted pair transmission products. • Three years on Spectra® IV products. • Three years on Genex® Series products (multiplexers, server, and keyboard).
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.