I N S TA L L AT I O N / O P E R AT I O N ® ICI1000PIM Personality Interface Module C1005M-G (10/02)
GENERAL UNPACKING INSTRUCTIONS Unpack and inspect all parts carefully. The following items are supplied: 1 1 1 ICI1000PIM Personality Interface Module RJ-14 cable for Inter-Check® and the DX2000 DVR RJ-45 coupler for the DX2000 DVR DESCRIPTION The ICI1000PIM Personality Interface Module (PIM) is a data protocol translator that translates data from cash registers and other devices for use with Pelco’s Inter-Check or DX2000 Digital Video Recorder (DVR).
INSTALLATION NOTE: The information in this manual is for PIM software version 4.02 and above. INSTALLATION FOR INTER-CHECK Refer to the ICI1000S Inter-Check manual as you install the ICI1000PIM. 1. Configure DIP switch bank 1 on the PIM (refer to Configuring DIP Switch Bank 1 section). 2. Configure DIP switch bank 2 on the PIM (refer to Configuring DIP Switch Bank 2 section). 3. Locate the 16-pin connector on your register/interface. Plug the register/interface connector into the PIM. 4.
TO INTER-CHECK UNIT STRAIGHT-THROUGH PHONE CABLE WHITE BLUE BLACK YELLOW RED GREEN USER-SUPPLIED CABLE, 18 AWG, SHIELDED WIRE IS SUGGESTED FROM ICI1000PIM WHITE BLUE BLACK YELLOW RED GREEN Figure 2.
INSTALLATION FOR DX2000 DVR AND DX2000DH DATA HUB Refer to Figure 3 and the DX2000 Digital Video Recorder Installation/Operation Manual (C690M) and DX2000DH Data Hub Manual (C698M) as you install the ICI1000PIM. 1. Configure DIP switch bank 1 (refer to the Configuring DIP Switch Bank 1 section) for the device to which you are interfacing. 2. Configure DIP switch bank 2 (refer to the Configuring DIP Switch Bank 2 section) for the device to which you are interfacing. 3.
CONFIGURING DIP SWITCH BANK 1 The switches in this bank serve several purposes. Selections include polling or non-polling operation, PIM addressing, clock signal manipulation, and ICI1000PIM graphics mode selection. The following describes the DIP switch settings for bank 1 on the ICI1000PIM. (Refer to Figure 4 and Tables A and B).
Table A.
Table B.
Table B.
SPECIFICATIONS ELECTRICAL Power Input Voltage: 120 VAC, 60 Hz to wall mounted transformer (5 VDC, 300 mA from transformer to ICI1000PIM) Connectors: One 16-pin interface connector One RJ-14 modular data connector One transformer power connector DIP Switches: Two eight-position DIP switches GENERAL Construction: Black plastic cover Environment: Indoor Operating Temperature: 32° to 120°F (0° to 49°C) Weight: Unit 1.80 lb (0.82 kg) Dimensions: 0.75" H x 4.94" W x 2.75" D (1.91 x 12.55 x 6.
WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on Pelco manufactured cameras (CC3500/CC3600/CC3700 and MC3500/MC3600 Series); two years on all other cameras. • Three years on Genex® Series (multiplexers, server, and keyboard). • Two years all standard motorized or fixed focal length lenses.
® World Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.
