® HS5000/HS5001 High Security/Harsh Environment Enclosure Installation/Operation Manual C489M-A (1/96) Pelco • 3500 Pelco Way, Clovis, CA 93612-5699 • USA • www.pelco.
TABLE OF CONTENTS Section Page 1.0 WARNINGS ........................................................................................................................................ 1 2.0 SCOPE ............................................................................................................................................... 2 3.0 DESCRIPTION ................................................................................................................................... 2 3.
LIST OF ILLUSTRATIONS Figure Page 1 HS5000 Wiper/Washer/Heater Connections ................................................................................... 3 2 Wiring Diagram for HS5001 Heaters ............................................................................................... 3 3 HS5000/HS5001 Exploded Assembly Drawing ............................................................................... 5 4 HS5000/HS5001 Dimension Drawing .................................................
(This page intentionally left blank.
INSTALLATION/OPERATION MANUAL HS5000/HS5001 HIGH SECURITY/ HARSH ENVIRONMENT ENCLOSURE 1.0 WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. 2. 3. Installation and servicing should only be done by Qualified Service Personnel and conform to all Local codes. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture. 4.
2.0 SCOPE 3.1 POWER REQUIREMENTS The information contained within this manual covers the HS5000/HS5001 High Security/Harsh Environment Camera Enclosure. HS5000 Heater: Wiper: Washer: Installation should be in accordance with all applicable local and national electric codes, utilizing approved materials only. 3.0 DESCRIPTION The HS5000/HS5001 is a high security/harsh environment camera enclosure designed for installations such as automated mining/excavation equipment, prisons, detention cells, etc.
4.0 INSTALLATION 4.2 HS5001 HEATER CONNECTION Before installing the HS5000/HS5001, make certain that the mounting surface is able to support the full load of the enclosure plus all other equipment such as camera, lens, etc. Heater connections for all models used with the HS5001 are wired the same. Refer to Figure 2 for proper wiring connections. NOTE: The fasteners required to secure the enclosure to a mounting surface are not supplied. The heaters are all thermostatically controlled.
4.3 CAMERA/LENS INSTALLATION 4.5 ENCLOSURE MOUNTING To install the camera/lens, perform the following steps: Secure the enclosure to the mounting surface with suitable fasteners (not supplied). 1. Remove the lid by removing the eight (8) 10-32 x 1/2" socket head cap screws. 2. Remove two (2) 6-32 x 3/8" socket head cap screws from the rear of the PC board. This will allow the PC board to be pivoted out of the way. 3.
6.0 EXPLODED ASSEMBLY DRAWING Figure 3.
7.0 MECHANICAL PARTS LIST The following parts list corresponds to the exploded assembly drawing in Figure 3.
8.0 SPECIFICATIONS Input Voltage: HS5000 HS5001 12 VDC 120/230/24VAC; optional 12VDC input if using 24VAC heater unit. Cable Entry: Two (2) .75" (1.91 cm) conduit holes Window: .5" (12.7 mm) thick, impact and abrasion resistant Lexan Camera Mounting: Removable camera sled with isolation mounts (4) Maximum Camera/Lens: Length Width: Height: 5.00" (12.7 cm) 2.00" (5.08 cm) 2.50" (6.
9.0 WARRANTY AND RETURN INFORMATION WARRANTY RETURNS Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair).
