I N S T A L L A T I O N ® ICS090 Series Camclosure® Housing (Not Upgradeable) C2477M (6/03)
CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS ..................................................................................... 3 WELCOME .......................................................................................................................................... 4 MODELS .................................................................................................................................... 4 REMOVE THE BUBBLE .........................................................
IMPORTANT SAFEGUARDS AND WARNINGS 1. Installation and servicing should be done only by qualified service personnel and conform to all local codes. 2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and must not be installed where exposed to rain and moisture. 3. Use only installation methods and materials capable of supporting four times the maximum specified load.
WELCOME Thank you for purchasing Pelco’s ICS090 Series Camclosure® housing for indoor applications. The unit is easy to install and can be mounted to the surface of a ceiling/wall or recessed in a ceiling/ wall. The following is supplied with the ICS090 Series housing: Qty. 1 1 2 2 2 2 Description Assembled ICS090 Series housing (back box and bubble) Adapter plate 8-32 x 1.00-inch Phillips pan head screws 8-32 x .750-inch self-tapping screws 8-32 x 2.50-inch self-tapping screws 10-32 x 1.
REMOVE THE BUBBLE Turn the bubble counterclockwise and lift (refer to Figure 1). Place the bubble on a nonabrasive surface. Figure 1.
INSTALL THE BACK BOX The installation methods for the ICS090 Series housing include the following: • Mount to the surface of a ceiling/wall • Install in a suspended ceiling • Install in a fixed ceiling/wall Select the best method for your installation and refer to the following pages for instructions. INSTALLATION TO SURFACE OF A CEILING/WALL Using 6-32 toggle bolts, attach the surface mount ring and back box to the mounting surface (refer to Figure 2).
IN-CEILING INSTALLATION – SUSPENDED CEILING Refer to Figure 4 for the following steps. 1. Remove the ceiling tile from the ceiling. 2. Cut a four-inch diameter hole in the ceiling tile. 3. Remove the surface mount ring from the back box. Refer to Figure 5 and do the following: a. Place fingers on the circular marks located on the sides of the surface mount ring. b. Pinch the sides. c. Lift and remove the surface mount ring from the back box.
IN-CEILING INSTALLATION – FIXED CEILING/WALL Refer to Figure 6 for the following steps. 1. Cut a four-inch diameter hole in the ceiling/wall. 2. Remove the surface mount ring from the back box. Refer to Figure 5 and do the following: a. Place fingers on the circular marks located on the sides of the surface mount ring. b. Pinch the sides. c. Lift and remove the surface mount ring from the back box. 3. Using 3-16 toggle bolts, attach the back box to the mounting surface.
REINSTALL THE BUBBLE To install the bubble refer to Figure 7 and do the following: 1. Align the standoffs of the bubble with the slots of the back box. 2. Turn the bubble clockwise until it locks in place. Figure 7.
SPECIFICATIONS General Construction Back Box and Surface Mount Ring: Bubble: Finish: Environment: Weight Unit: Shipping: ABS plastic Polycarbonate White Indoor .52 lb (.24 kg) 2 lb (.91 kg) (Design and product specifications subject to change without notice.) 5.30 (13.46) 5.72 (14.53) 1.65 (4.19) 4.04 (10.26) 4.04 (10.26) 2.39 (6.07) 3.90 (9.91) 3.90 (9.91) NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES.
WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • • • • • • • • • • Five years on Pelco manufactured cameras (CC3500/CC3600/CC3700 and MC3500/MC3600 Series); two years on all other cameras. Three years on Genex® Series (multiplexers, server, and keyboard) and 090 Series Camclosure® Camera System.
® World Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.
