INSTALLATION/OPERATION IPS-RDPE-2 Remote Data Port C2473M-D (10/06)
Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Required Accessories . . . . . . . . . . . . . . . . . . . .
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Installation should be done only by qualified personnel and conform to all local codes. 6. Use only installation methods and materials capable of supporting four times the maximum specified load. 7. Use stainless steel hardware to fasten the mount to outdoor surfaces. 8. Use only replacement parts recommended by Pelco. 9.
Description Pelco’s IPS-RDPE-2 data port box is an on-site service tool designed for Spectra®, Esprit®, and ExSite™ Series positioning systems. The data port box gives on-site access for setup and testing of the positioning system. The IPS-RDPE-2 can be used to locally view video and control pan/tilt/zoom functions of a Spectra, Esprit, or ExSite system. The data port box can also upload revised operating software and language files to a Spectra or ExSite system.
Mounting Instructions WALL MOUNTING 1. Open the lid of the IPS-RDPE-2 box. Install two 3/4-inch (1.91 cm) conduit fittings (not supplied). Close the lid of the IPS-RDPE-2 box. 2. Determine the mounting location for the IPS-RDPE-2. 3. Use the IPS-RDPE-2 box as a template and mark the four fastener positions on the mounting surface. 4. Prepare the holes for installation. 5. Attach the IPS-RDPE-2 securely with four fasteners of appropriate length.
POLE MOUNTING 1. Install the PA402 mount adapter. Refer to the instructions supplied with the adapter. 2. Open the lid of the IPS-RDPE-2 box. Install two 3/4-inch (1.91 cm) conduit fittings (not supplied). Close the lid of the IPS-RDPE-2 box. 3. Attach the IPS-RDPE-2 to the PA402 and secure with the hardware supplied with the mount adapter. Refer to Figure 2. IPS-RDPE-2 CONDUIT FITTINGS PA402 Figure 2. Mounting to Pole with PA402 4. Run conduit with wiring from the positioning system to the IPS-RDPE-2.
Cable/Wire Requirements and Connector Locations Refer to Figure 3 for a layout of the data port box connectors. It is important to connect all four communication wires from the IPS-RDPE-2 to the Spectra dome system or ExSite system. It will not be possible to perform software and language file uploads if the transmit and receive wires are not connected. OPTIONAL =POSITIONING SYSTEM CONNECTIONS Figure 3. IPS-RDPE-2 Connections NOTES: 8 • Input power for the IPS-RDPE-2 is 24 VAC only.
Wiring Diagrams The IPS-RDPE-2 is designed to work in both coaxial cable and UTP video transmission systems.
POSITIONING SYSTEM VC-UTP POWER UTP- UTP+ TX+ TX- RX+ RX- PTZ CONTROL AND SOFTWARE UPLOAD IPS-RDPE-2 RX- RX+ TX- TX+ RX- RX+ TX- TX+ UTP- UTP+ UTP- UTP+ 24 VAC- 24 VAC+ 24 VAC- 24 VAC+ UTP- UTP+ VIDEO IN VIDEO OUT COAXITRON CONTROLLER TO POWER SUPPLY Figure 5. Coaxitron Controller with UTP Video – Passive Receiver Only NOTES: 10 • Input power for the IPS-RDPE-2 is 24 VAC only. The maximum wire gauge allowed for power input and output is 12 AWG.
PTZ CONTROL AND SOFTWARE UPLOAD POSITIONING SYSTEM OR POWER TX+ TX- RX+ RX- VIDEO OUT PTZ CONTROL ONLY IPS-RDP RX- RX+ TX- TX+ UTP- UTP+ 24 VAC- 24 VAC+ 24 VAC- 24 VAC+ RX- RX+ TX- TX+ UTP- UTP+ VIDEO IN TO POWER SUPPLY TX- TX+ RX- RX+ CONTROL SYSTEM VIDEO OUT VIDEO IN AT CONTROL SYSTEM Figure 6. RS-422 (D or P Protocol) Controller with Coax Video – Point-to-Point Configuration NOTES: • Input power for the IPS-RDPE-2 is 24 VAC only.
PTZ CONTROL AND SOFTWARE UPLOAD POSITIONING SYSTEM OR POWER TX+ TX- RX+ RX- PTZ CONTROL ONLY VIDEO OUT IPS-RDPE-2 RX- RX+ TX- TX+ PTZ CONTROL AND SOFTWARE UPLOAD 24 VAC- 24 VAC+ 24 VAC- 24 VAC+ RX- RX+ TX- TX+ UTP- UTP+ TO POWER SUPPLY VIDEO IN POSITIONING SYSTEM TX+ TX- RX+ RX- VIDEO OUT TX- TX+ RX- RX+ VIDEO IN CONTROL SYSTEM AT CONTROL SYSTEM OR POWER UTP- UTP+ VIDEO OUT VIDEO IN PTZ CONTROL ONLY AT CONTROL SYSTEM IPS-RDPE-2 24 VAC- 24 VAC+ 24 VAC- 24 VAC+ RX- RX+ TX- TX+ R
PTZ CONTROL AND SOFTWARE UPLOAD POSITIONING SYSTEM OR POWER TX+ TX- RX+ RX- PTZ CONTROL ONLY VIDEO OUT IPS-RDPE-2 RX- RX+ TX- TX+ 24 VAC- 24 VAC+ PTZ CONTROL AND SOFTWARE UPLOAD 24 VAC- 24 VAC+ RX- RX+ TX- TX+ UTP- UTP+ TO POWER SUPPLY UTP- UTP+ VIDEO IN VIDEO OUT POSITIONING SYSTEM OR POWER TX+ TX- RX+ RX- TX- TX+ RX- RX+ VIDEO IN CONTROL SYSTEM AT CONTROL SYSTEM VIDEO OUT PTZ CONTROL ONLY VIDEO IN AT CONTROL SYSTEM IPS-RDPE-2 24 VAC- 24 VAC+ 24 VAC- 24 VAC+ RX- RX+ TX- TX+ RX
POSITIONING SYSTEM VC-UTP POWER UTP- UTP+ TX+ TX- RX+ RX- PTZ CONTROL AND SOFTWARE UPLOAD IPS-RDPE-2 RX- RX+ TX- TX+ UTP- UTP+ 24 VAC- 24 VAC+ 24 VAC- 24 VAC+ RX- RX+ TX- TX+ UTP- UTP+ TO POWER SUPPLY TX- TX+ RX- RX+ CONTROL SYSTEM UTP- UTP+ UTP RECEIVER AT CONTROL SYSTEM Figure 9. RS-422 (D or P Protocol) Controller with UTP Video – Point-to-Point Configuration NOTES: 14 • Input power for the IPS-RDPE-2 is 24 VAC only.
POSITIONING SYSTEM VC-UTP POWER TX+ TX- RX+ RX- UTP- UTP+ PTZ CONTROL AND SOFTWARE UPLOAD IPS-RDPE-2 RX- RX+ TX- TX+ POSITIONING SYSTEM 24 VAC- 24 VAC+ 24 VAC- 24 VAC+ RX- RX+ TX- TX+ UTP- UTP+ UTP- UTP+ TO POWER SUPPLY VC-UTP POWER TX+ TX- RX+ RX- TX- TX+ RX- RX+ UTP- UTP+ UTP- UTP+ CONTROL SYSTEM UTP RECEIVER PTZ CONTROL AND SOFTWARE UPLOAD AT CONTROL SYSTEM IPS-RDPE-2 UTP- UTP+ UTP RECEIVER 24 VAC- 24 VAC+ 24 VAC- 24 VAC+ RX- RX+ TX- TX+ RX- RX+ TX- TX+ UTP- UTP+ UTP- UTP+
POSITIONING SYSTEM VC-UTP POWER TX+ TX- RX+ RX- UTP- UTP+ PTZ CONTROL AND SOFTWARE UPLOAD IPS-RDPE-2 RX- RX+ TX- TX+ POSITIONING SYSTEM 24 VAC- 24 VAC+ 24 VAC- 24 VAC+ RX- RX+ TX- TX+ UTP- UTP+ UTP- UTP+ TO POWER SUPPLY VC-UTP TX- TX+ RX- RX+ POWER TX+ TX- RX+ RX- UTP- UTP+ UTP- UTP+ CONTROL SYSTEM UTP RECEIVER AT CONTROL SYSTEM PTZ CONTROL AND SOFTWARE UPLOAD UTP- UTP+ IPS-RDPE-2 UTP RECEIVER AT CONTROL SYSTEM 24 VAC- 24 VAC+ 24 VAC- 24 VAC+ RX- RX+ TX- TX+ RX- RX+ TX- TX+ UTP
Operation To view video, control pan/tilt/zoom, or upload revised operating software and language files to a positioning system, do the following: 1. Open the door of the IPS-RDPE-2. Opening the door will automatically disconnect the controller at the head-end and trigger an audible alert at the IPS-RDPE-2 site. NOTE: The audible alert indicates that the data port is in service mode and also serves as a reminder to close the door after servicing the positioning system. 2.
Specifications ELECTRICAL Input Voltage 24 VAC Power Consumption 1 VA Does not include power required for positioning system MECHANICAL Construction Aluminum Finish Gray polyester powder coat Cable Entry Two hole plugs will accommodate 3/4-inch (1.91 cm) conduit fittings (not supplied) Mount Method Four 0.375-inch (0.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FR/FT/FS Series fiber optic products and TW3000 Series unshielded twisted pair transmission products. • Three years on Genex® Series products (multiplexers, server, and keyboard).
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.
