INSTALLATION/OPERATION ES30C/ES31C Series Esprit® with IOP C307M-I (11/05)
Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IR Filter Mode (Models ES30CBW18/ES31CBW18/ES30CBW24/ES31CBW24) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Limit Stops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Turning Limit Stops On Or Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 6. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 7. Only use attachments/accessories specified by the manufacturer. 8.
Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules.
Description The ES30C and ES31C Series combine a receiver, pan and tilt, enclosure, and Integrated Optics Package (IOP) in a single, easy-to-install system. The Integrated Optics Package contains an auto-focus camera and lens module with programmable features. The ES30C and ES31C systems are available with an input voltage of 24 VAC or with a selectable power source of 120/230 VAC. The systems are constructed of lightweight aluminum and have a heater, window defroster, sun shroud, and insulation blanket.
Installation 1. When installing the ES30C/ES31C Esprit® system, allow for sufficient clearance between the top of the unit and overhead obstructions. This will prevent interference when the enclosure is driven to its maximum elevation of 33 degrees. Model ES30 ES31 A 16.6 (42.5) 16.9 (42.9) B 9.4 (23.9) 9.7 (24.6) C 7.1 (18.1) 7.6 (19.2) D 4.2 (10.7) 4.6 (11.7) A 33.0° B NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES. D C LOOSEN PHILLIPS SCREWS TRANSFORMER MODULE 2.
4. Route the wires and cables through the center of the Esprit mount. Reinstall the transformer module into the base. The transformer module can be positioned in the mount base in only one orientation. 120/230 VOLTAGE SELECTOR SWITCH 5. ES30C-5/ES31C-5 Models Only: Set the 120/230 voltage selector switch on the transformer to the appropriate voltage. 6. Connect wires and cables. a. Connect to power. Use the two supplied clamp connectors to connect the AC line and neutral.
USER ACCESSORY ESPRIT K1 OMRON G5V-1-DC12 D1 1N4005 AUX 2 ORANGE WIRE AUX 2 COM BLUE WIRE V1 32 VDC AUX 2 AUX 2 COM NOTE: CURRENT MUST NOT EXCEED 40 mA. 7. Install mount; refer to the installation manual supplied with the mount for instructions. 8. Turn on the power. If the red LED lights, turn off the power and proceed to the next step. If the red LED does not light, refer to the Troubleshooting section. 9.
TXB Series Translator Board Installation (Optional) Pelco’s TXB Series allows controllers from other companies to communicate with the Esprit system. To install a TXB Series board, remove the left cover of the pan and tilt. Once the cover is removed, refer to the manual supplied with the translator board to complete the installation. HOW TO REMOVE THE PAN AND TILT COVER 1. Unscrew the Phillips head screw located on the left cover of the pan and tilt. 2. Remove cover and place to the side.
HOW TO REINSTALL THE PAN AND TILT COVER The pan and tilt covers must be properly seated and have a tight seal all the way around when installed. NOT SEALED THIS SIDE IS IMPROPERLY INSTALLED THIS SIDE IS PROPERLY INSTALLED GAP To reinstall the pan and tilt cover, do the following: 1. Properly position the cover and slide it into place. The sides of the cover must fit under the front and back rain guards of the pan and tilt, and the top of the cover must seat against the lip of the top gasket. 2.
Operation POWER-UP DISPLAY When the system is powered up, the selected protocol, revision number, and other information is displayed on the monitor. For example, the screen might show the following information: ESPRIT 16X IOP 1.0h CONFIGURE DONE D Address 1 P Address 2 Comm 2400, N, 8, 1 The information displayed depends on the selected protocol (C, D, or P) and the menu selection for power-up mode. (Refer to Power-Up Mode in the Programming section).
OPERATING NOTES ENVIRONMENTAL RANGE The operating temperature ranges from a minimum of -50°F (-45°C) to a maximum of 122°F (50°C) for sustained system operation or 140°F (60°C) absolute maximum. The entire unit can de-ice and be operational in two hours from a temperature of -13°F (-25°C). The thermostatically controlled heater consumes 10 watts and cycles on at 70°F (21°C) and off at 85°F (29°C), while the window defroster runs continuously and consumes 2.5 watts.
PATTERNS The Esprit system can do either one full pattern (1.5, 3, or 6 minutes long) or two half patterns (.75, 1.5, or 3 minutes long). This pattern can consist of any standard pan and tilt or lens command. Presets, flip, digital zoom, proportional pan, and turbo are not allowed in a pattern. Zones can be enabled while running a pattern. Refer to the documentation for your control system to program and run patterns.
Programming – ES30C16/ES31C16 1. Access main menu (preset 95). 2. Make main menu selections. Joystick: Move up or down to position cursor or to toggle between selections. Iris Open: Enter. Camera Menu Iris Close: Cancel.
Programming – ES30C22/ES31C22 1. Access main menu (preset 95). 2. Make main menu selections. Joystick: Move up or down to position cursor or to toggle between selections. Iris Open: Enter. Camera Menu Iris Close: Cancel.
Programming – ES30CBW18/ES31CBW18/ES30CBW24/ES31CBW24 1. Access main menu (preset 95). 2. Make main menu selections. Joystick: Move up or down to position cursor or to toggle between selections. Iris Open: Enter. Camera Menu Iris Close: Cancel.
Programming ACCESSING MAIN MENU (PRESET 95) You can call up the main menu on your monitor by programming (setting or creating) preset 95 (28 if in 32-preset mode). Programming preset 95 for Pelco’s controllers varies according to the type of controller you are using. Instructions for programming preset 95 are given below for various Pelco controllers. CM6700 1. Enter the number of the camera and press the CAM key. 2. Enter 95 and hold the PRESET key for two seconds. 3.
CM9740/CM9760/CM9770 1. Press the ESCAPE key to open the Main menu. Select DEF. The Define Menu appears. 2. Enter your four-digit PIN if this is your first time entering this mode. 3. Enter 95 and select PRST. The main menu appears on the monitor. 4. Select the Quit icon to return to the default menu. KBD4000/KBD4002/KBD4000V 1. Press the SPOT MONITOR key. 2. Enter 95, and then hold the PRESET key (approximately five seconds) until the main menu appears on the screen. MPT9500 Standard Coaxitron® Mode 1.
AUTO FOCUS MODE MAIN MENU Exit Next Menu Camera Menu Backlight comp Zoom limit Reset camera Next Exit Off x- - LowLight limit Shutter speed Auto focus mode Prev Exit Auto Auto There are two auto focus modes: Auto: If auto focus is in the auto mode, pressing the Focus Far or Focus Near button will place the focus in the manual mode.
AUTO IRIS MAIN MENU Auto Iris Menu Camera Menu Exit Backlight comp Zoom limit Reset camera Next Exit Off x- - Auto-iris mode Auto-iris level Auto-iris peak Exit Auto The following are the settings for auto iris: Mode Level Peak To change the settings for auto iris: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button to enter the Camera menu. 4.
AUTO IR LEVEL (MODELS ES30CBW18/ES31CBW18/ES30CBW24/ES31CBW24) MAIN MENU Exit IR Filter Menu Next Menu Camera Menu Backlight comp Zoom limit Reset camera Next Exit Off x- - LowLight limit Shutter speed Auto focus mode Prev Exit Auto Auto Auto IR filter mode Auto IR Level Exit Auto Dusk The auto IR level is the light level at which the infrared filter switches IN or OUT.
AUTO SHARPNESS MAIN MENU Exit Sharpness Menu Next Menu Camera Menu Backlight comp Zoom limit Reset camera Next Exit Off x- - LowLight limit Shutter speed Auto focus mode Prev Exit Auto Auto Auto Auto Sharpness Sharpness Exit On 13 The following settings are available for auto sharpness: On: Automatically sets the sharpness of the camera.
AZ/EL MAIN MENU Exit Other Menu Proportional pan Park time minutes Scan Speed deg/s Pattern Length Spd Profile Exit Az/El/Direction On 0 25 1.5 min Set Azimuth Zero Az/El Az/El Line Direction Direction Line Zoom Zoom Line Disp Duration Exit Az/El programs the horizontal display position of the Azimuth1/Elevation2 label. NOTE: Az/El display is not available while you are programming or running a pattern.
AZ/EL LINE MAIN MENU Exit Other Menu Proportional pan Park time minutes Scan Speed deg/s Pattern Length Spd Profile Exit Az/El/Direction On 0 25 1.5 min Set Azimuth Zero Az/El Az/El Line Direction Direction Line Zoom Zoom Line Disp Duration Exit Az/El Line controls the vertical display position of the Azimuth/Elevation label. The label may be displayed on lines 3 through 10.
AZIMUTH ZERO MAIN MENU Exit Other Menu Proportional pan Park time minutes Scan Speed deg/s Pattern Length Spd Profile Exit Az/El/Direction On 0 25 1.5 min Set Azimuth Zero Az/El Az/El Line Direction Direction Line Zoom Zoom Line Disp Duration Exit Azimuth is the pan angle from 0° to 359°. Azimuth zero is the programmed 0° point that is normally set to magnetic north.
BACKLIGHT COMPENSATION MAIN MENU Exit Camera Menu Backlight comp Zoom limit Reset camera Next Exit Off x- - There are two backlight compensation modes: On: The system uses the center 10 percent of the picture to adjust the iris. If there is a bright light source outside of this area, it will wash out to white. The camera will adjust the iris so that the object in the sensitive area is properly exposed.
DIRECTION MAIN MENU Exit Other Menu Proportional pan Park time minutes Scan Speed deg/s Pattern Length Spd Profile Exit Az/El/Direction On 0 25 1.5 min Set Azimuth Zero Az/El Az/El Line Direction Direction Line Zoom Zoom Line Disp Duration Exit Direction programs the horizontal display position of the Direction label (N, NW, NE, …).
DIRECTION LINE MAIN MENU Exit Other Menu Proportional pan Park time minutes Scan Speed deg/s Pattern Length Spd Profile Exit Az/El/Direction On 0 25 1.5 min Set Azimuth Zero Az/El Az/El Line Direction Direction Line Zoom Zoom Line Disp Duration Exit Direction Line controls the vertical display position of the Direction label. The label may be displayed on lines 3 through 10.
DISPLAY DURATION MAIN MENU Exit Other Menu Proportional pan Park time minutes Scan Speed deg/s Pattern Length Spd Profile Exit Az/El/Direction On 0 25 1.5 min Set Azimuth Zero Az/El Az/El Line Direction Direction Line Zoom Zoom Line Disp Duration Exit Display Duration programs the duration the Az/El, Direction, and Zoom labels are displayed on the monitor.
GAIN/AGC MAIN MENU Exit Gain/AGC Menu Camera Menu Backlight comp Zoom limit Reset camera Next Exit Off x- - Gain Limit Exit 27 GAIN LIMIT The gain limit sets the maximum level for the automatic gain control. Increasing the level will increase the signal level and increase the noise level of the picture. To change the gain: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3.
IR FILTER MODE (MODELS ES30CBW18/ES31CBW18/ES30CBW24/ES31CBW24) MAIN MENU Exit IR Filter Menu Next Menu Camera Menu Backlight comp Zoom limit Reset camera Next Exit Off x- - LowLight limit Shutter speed Auto focus mode Prev Exit Auto Auto Auto IR filter mode Auto IR Level Exit Auto Dusk There are two settings for the IR filter mode: Auto: IR filter switches in and out automati
LIMIT STOPS MAIN MENU Exit Limit Stop Menu Limit Stops Set Man Limits Clear Man Limits Set Scan Limits Clear Scan Limits Exit Off NOTE: Limit stops are inactive while setting items in the program menu (e.g. azimuth zero, scan limits, manual pan limits). TURNING LIMIT STOPS ON OR OFF To change the limit stop mode: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Limit Stop. 3.
Limit Stops Menu The manual pan limit stops can be set at the controller using the Limit Stops menu: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Limit Stop. 3. Press the Iris Open button to enter the Limit Stop menu. 4. Move the cursor to Set Man Limits and press the Iris Open button. PRESS IRIS OPEN TO SET LEFT LIMIT appears. 5. Move the pan and tilt to the desired left limit position and press the Iris Open button to set the left manual limit.
Limit Stops Menu The manual pan limit stops can be set at the controller using the Limit Stops menu: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Limit Stop. 3. Press the Iris Open button to enter the Limit Stop menu. 4. Move the cursor to Set Scan Limits and press the Iris Open button. PRESS IRIS OPEN TO SET LEFT LIMIT appears. 5. Move the pan and tilt to the desired left limit position and press the Iris Open button to set the left manual limit.
LINE SYNCHRONIZATION Line Sync Menu MAIN MENU Exit Line Sync Line Sync Phase Exit On 0 If cameras are out of phase with each other, they may produce what appears to be vertical roll when switching between cameras. There are two settings for line synchronization: On: Adjust the synchronization of the power line voltage so that it is in phase with other cameras. Off: The system synchronizes to an internal clock.
LOWLIGHT LIMIT (MODELS ES30C22/ES31C22, ES30CBW18/ES31CBW18, AND ES30CBW24/ES31CBW24) MAIN MENU Next Menu Camera Menu Exit Backlight comp Zoom limit Reset camera Next Exit Off x- - LowLight limit Shutter speed Auto focus mode Prev Exit Auto Auto This setting determines the maximum length of time the shutter will remain open automatically in low light conditions.
PARK TIME MINUTES MAIN MENU Exit Other Menu Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.5 min Spd Profile 90 MPH wind Exit This feature causes the system to park at preset 1 after a programmed number of minutes of control inactivity. The time can be set from 1 minute to 720 minutes (12 hours), or it can be set to zero, which disables this feature. NOTE: Preset 1 must be programmed for the dome to park.
PATTERN LENGTH MAIN MENU Exit Other Menu Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.5 min Spd Profile 90 MPH wind Exit The Esprit can do the following: One full pattern - 1.5, 3, or 6 minutes long or Two half patterns - .75, 1.5, or 3 minutes long This pattern can consist of any standard pan, tilt, or lens command. Presets, flip, and turbo are not allowed in a pattern.
POWER-UP MODE MAIN MENU Exit Power-Up Menu Power Up Default Exit This feature lets the dome resume a desired condition following power-up. The menu includes the following choices. Default: On power-up, the system goes through a configuration cycle and stops at zero reference, showing “Configuration Done,” address, and mode settings on the screen. Park: The system moves to preset 1 when the power-up sequence finishes.
PROPORTIONAL PAN MAIN MENU Exit Other Menu Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.5 min Spd Profile 50 MPH wind Exit There are two proportional pan modes: On: Enables the proportional pan mode. The amount of zoom controls the pan and tilt. At telephoto zoom settings, the pan and tilt speeds will be slower for a given amount of joystick deflection than at wide zoom settings.
RESET CAMERA MAIN MENU Exit Camera Menu Backlight comp Zoom limit Reset camera Next Exit Off x- - Resetting the camera returns the settings to their defaults.
SCAN SPEED MAIN MENU Exit Other Menu Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.5 min Spd Profile 50 MPH wind Exit The scan speed is adjustable from 1-40 degrees per second. This occurs in three scan modes: auto, random, and frame scan. To change the scan speed: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Other. 3.
SHARPNESS MAIN MENU Exit Sharpness Menu Next Menu Camera Menu Backlight comp Zoom limit Reset camera Next Exit Off x- - LowLight limit Shutter speed Auto focus mode Prev Exit Auto Auto Auto Auto Sharpness Sharpness Exit On 13 Use the Sharpness setting to manually set the sharpness of the camera. To manually set the sharpness of the camera: 1. Program preset 95 (28). The main menu appears.
SHUTTER SPEED MAIN MENU Exit Next Menu Camera Menu Backlight comp Zoom limit Reset camera Next Exit Off x- - LowLight limit Shutter speed Auto focus mode Prev Exit Auto Auto There are several electronic shutter speed settings: Auto 1/2 1/4 1/8 1/15 1/30 1/60 1/120 1/180 1/250 1/500 1/1000 1/2000 1/4000 1/10,000 1/30,000 In the Auto setting the camera controls the shutter speed automatically.
SPEED PROFILE MAIN MENU Exit Other Menu Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.5 min Spd Profile 50 MPH wind Exit This feature allows the operator to set the wind speed conditions for the location of the Esprit system. You can set two wind speed profiles of 50 mph or 90 mph in which the system will remain operational. In both settings, the pan speed will be a maximum of 40 degrees per second.
WHITE BALANCE The settings for white balance are as follows: Auto white bal R Gain B Gain To change the white balance settings: MAIN MENU Exit Next Menu Camera Menu Backlight comp Zoom limit Reset camera Next Exit Off x- - LowLight limit Shutter speed Auto focus mode Prev Exit White Balance Menu Auto Auto Auto Auto white bal R Gain B Gain Exit On 182 182 1.
WIPER MODE MAIN MENU Exit Wiper Menu Wiper Mode Momentary Wiper Dwell 2 Wiper Time 60 Exit There are three wiper settings: Wiper Mode Wiper Dwell Wiper Time To change the wiper settings: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Wiper. 3. Press the Iris Open button to enter the Wiper menu. 4. Move the joystick up or down to position the cursor next to one of the wiper settings. 5.
ZONE BLANK MAIN MENU Exit Other Menu Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.5 min Spd Profile 90 MPH wind Exit Zone Blank Menu Video Blank Zone 1 Off 2 Off 3 Off 4 Off 5 Off 6 Off 7 Off 8 Off Exit The Esprit system features onscreen programmable zone blanking. This feature lets you define any zone as blanked for video (viewing/recording).
ZOOM MAIN MENU Exit Other Menu Proportional pan Park time minutes Scan Speed deg/s Pattern Length Spd Profile Exit Az/El/Direction On 0 25 1.5 min Set Azimuth Zero Az/El Az/El Line Direction Direction Line Zoom Zoom Line Disp Duration Exit Zoom programs the horizontal display position of the Zoom label. The following settings are available for the Zoom label: Off: Label is not displayed.
ZOOM LIMIT MAIN MENU Exit Camera Menu Backlight comp Zoom limit Reset camera Next Exit Off x- - ES30C16/ES31C16: 16X optical zoom and 10X electronic zoom, can be set for 16X, 32X, 64X, 128X, or 160X. ES30C22/ES31C22: 22X optical zoom and 10X electronic zoom, can be set for 22X, 32X, 88X, 176X, or 220X. ES30CBW18/ES31CBW18: 23X optical zoom and 10X electronic zoom, can be set for 23X, 32X, 92X, 184X or 230X.
ZOOM LINE MAIN MENU Exit Other Menu Proportional pan Park time minutes Scan Speed deg/s Pattern Length Spd Profile Exit Az/El/Direction On 0 25 1.5 min Set Azimuth Zero Az/El Az/El Line Direction Direction Line Zoom Zoom Line Disp Duration Exit Zoom Line controls the vertical display position of the Zoom label. The label may be displayed on lines 3 through 10.
Troubleshooting Symptom: System does not operate. 1. Check system input voltage. 2. The Esprit system is protected by a resettable overcurrent protective device located in the transformer module. Whenever a fault condition is experienced in the system causing excessive current flow through the protective device, a change occurs that will prevent current flow. The protective device will remain in this state as long as power is applied and the system fault remains.
Symptom: No video or poor video 1. Check the video and power connections to the camera. 2. Check for power to the camera from the Esprit system camera power output. 3. Check all coax BNC connectors from the camera to the monitor. 4. Make sure the controller is set for the correct camera-to-monitor viewing combination; for example, Camera 1 to Monitor 1. Refer to the controller manual for information. 5. Check for normal load termination of 75 ohms.
APPENDIX NOTE: Esprit will sense and automatically select input from Coaxitron control signals in either the standard or extended mode. Therefore, the DIP switches settings have no effect on Coaxitron control signals. Table A. Switch Settings for SW1 Baud Rate Switch Setting SW1-1 SW1-2 SW1-3 2400 OFF OFF OFF* 4800 ON OFF OFF* 9600 OFF ON OFF* *SW1-3 is not used; set it in the OFF position.
NOTE: The Esprit will sense and automatically select input from Coaxitron control signals in either the standard or extended mode. Therefore, the DIP switches settings have no effect on Coaxitron control signals. Table B.
Table C.
Table C.
Table C.
Table C.
Table C.
Specifications ELECTRICAL Input Voltage 24, 120, or 230 VAC, 50/60 Hz; switch selectable for 120/230 VAC inputs. Reset feature enabled when power becomes unstable or interruped.
Zoom Ratio ES30C16/ES31C16 ES30CBW18/ES31CBW18 ES30C22/ES31C22 ES30CBW24/ES31CBW24 16X optical zoom, 10X electronic zoom 23X optical zoom, 10X electronic zoom 22X optical zoom, 10X electronic zoom 24X optical zoom, 10X electronic zoom Digital Slow Shutter Auto/manual speed selection Horizontal Angle of View ES30C16/ES31C16 ES30CBW18/ES31CBW18 ES30C22/ES31C22 ES30CBW24/ES31CBW24 43° at 4 mm wide zoom; 3° at 64 mm telephoto zoom 54° at 3.6 mm wide zoom; 2.5° at 82.
13.3 (33.9) 5.2 (13.3) 3.9 (9.9) 17.5 (44.3) 14.6 (37.0) 9.8 (24.9) 3.6 (9.1) 7.7 (19.7) 7.9 (20.0) NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES.
C307M-I (11/05)
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex ® Series products (multiplexers, server, and keyboard).
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.
