Q U I C K S T A R T IX and IXE Series Network Camera Sarix™ Technology C2951M-A (2/09)
ACT Camera Layout 24V~ RELAY ALARM ACC RESET LINK PoE R1 A1 (FRONT COVER OPENED) F V Figure 1.
ì RJ-45 Connector: Supplies power to the camera through the network using PoE. If PoE is not available, the camera is prewired for 24 VAC. î Ethernet Activity LED: Flashes green to indicate that data is being transmitted/received by the camera. ï Ethernet Link LED: Glows solid amber to indicate that a live connection is established. ñ Accessory Port: Reserved for future use.
Installation NOTES: • For detailed instructions, refer to the IX Series Installation/Operation manual (C2950M) or IXE Series Installation/Operation manual (C2953M) available on the resource disc. • Megapixel lenses are designed and tested to deliver optimal image quality to the IX Series and IXE Series megapixel cameras. A standard definition lens installed on a megapixel camera will limit the resolution of the camera and create poor image quality. 1. Install the lens: a.
3. Plug the network cable into the RJ-45 connector located at the back of the camera (refer to Figure 3). 1 8 87 8 Pin Function 1 TX+ 65 TX- 3 RX+ 4 PoE 1-2 5 PoE 1-2 43 2 21 1 2 3 4 5 6 7 8 1 2 3 4 6 7 8 6 RX- 7 PoE 3-4 8 PoE 3-4 8 5 1 7 6 5 4 3 2 1 Figure 3. Pin Descriptions 4. Attach the supplied ferrite to the network cable. The ferrite should be installed on the cable approximately 1 inch from the camera’s RJ-45 connector.
Operation Once the camera is installed, apply power to the camera. The camera will start a configuration sequence. The green LED flashes five times per second for approximately two minutes, and then turns solid after the boot cycle is complete and the camera is online. IP ADDRESS SETTINGS If the camera is connected to a DHCP network and DHCP is set to the On position, the server will automatically assign an IP address to the device; DHCP On is the default setting for the camera.
LIVE PAGE ICONS Viewable icons are based on group permissions. The camera has two predefined groups: Public and Admin. Public: This defined group can be modified or deleted. The default permission for this group is single stream view. Admin: This is the only defined group that cannot be deleted; however, the administrator password can be changed. For security purposes, it is important that you change your password after you log on to the device for the first time. This group has access to all permissions.
SETTINGS PAGE Depending on user permissions, the Settings page allows you to manage camera system settings, set up users and groups, and control the camera. To access the camera settings: 1. Log on to the camera. 2. Click the Settings link in the navigation bar located in the upper-right corner of the page; a list of menu tabs appear. Place the mouse pointer over a tab to display a list of submenus.
IMAGING TAB General: Includes camera orientation and digital processing settings. The orientation settings allow for standard or inverted installation of the camera. The digital processing settings adjust the sharpness, saturation, and contrast of the scene. Exposure: Adjusts scene detail and contrast. A scene with correct exposure settings has adequate detail and contrast between white and dark values. An image with too little or too much exposure eliminates detail in the scene.
REVISION HISTORY Manual # C2951M C2951M-A Date 1/09 2/09 Comments Original version. Revised installation instructions. Pelco, the Pelco logo, Camclosure, Digital Sentry, Endura, Esprit, ExSite, Genex, Intelli-M, Legacy, and Spectra are registered trademarks of Pelco, Inc. Spectra III and Sarix are trademarks of Pelco, Inc. All product names and services identified throughout this document are trademarks or registered trademarks of their respective companies.
www.pelco.com Pelco, Inc.
