Manual

ManualsBrandsPelco ManualsAccessoriesParapet Mount Adapter for Intercept or Spectra/DF5

IMPORTANT SAFEGUARDS AND WARNINGS

Prior to installation and use of this product, the following WARNINGS should be observed.

1. Installation and servicing should only be done by qualified service personnel and conform

to all local codes.

2. Installation shall be done in accordance with all local and national electrical and mechani-

cal codes utilizing only approved materials.

3. Use only installation methods and materials capable of supporting four times the maxi-

mum specified load.

4. Use stainless steel hardware to fasten the mount to outdoor surfaces.

5. To prevent damage from water leakage when installing a mount outdoors on a roof or

wall, apply sealant around the bolt holes between the mount and mounting surface.

Please thoroughly familiarize yourself with the information in this manual prior to installation

and operation.

C212M-B (8/04)

PP350/PP450 Parapet Mount

PP351/PP451 Rooftop Mount

3500 Pelco Way,

Clovis, CA 93612-5699

USA

In North America & Canada:

Tel (800) 289-9100

FAX (800) 289-9150

International Customers:

Tel (1-559) 292-1981

FAX (1-559) 348-1120

www.pelco.com

DESCRIPTION

The PP350 and PP351 mounts were designed for outdoor use with small-size pendant domes,

and the PP450 and PP451 are for outdoor use with medium-size pendant domes. The PP350

and PP450 models mount to parapets, while the PP351 and PP451 models mount to rooftops

or other smooth horizontal surfaces. All models accommodate domes that use 1.5-inch NPT

pipe.

The PP450 and PP451 can be used in applications where mounting and height clearances of

models PP350 and PP351 are inadequate. Models PP450 and PP451 are higher by 9.72

inches (24.69 cm) and the overhang is increased by 14.77 inches (37.52 cm).

The mounts are designed to swivel within available clearance limits, which adds to the flexibility,

easy maintenance, and usability of the configuration.

Manufactured from aluminum, the mounts include indexing bolts to secure the arm in position.

Models

PP350 Parapet mount for small-size pendant domes; mounts to inside or outside of

parapet.

PP351 Rooftop or smooth horizontal surface mount for small-size pendant domes.

PP450 Same as PP350 except overhang clearance and height accommodate medium-

size pendant domes.

PP451 Same as PP351 except overhang clearance and height accommodate medium-

size pendant domes.

INSTALLATION

Before Beginning

The hardware to install the mount depends on your installation requirements. The mount has

pre-drilled holes for use with 3/8-16 type hardware. (This hardware is not included with the

mount.) Use as many of the mounting holes as possible. Pelco recommends 3/8-16 type fasten-

ing hardware. Multiple fastening positions facilitate mounting flexibility. For models PP350 and

PP450, mount using a minimum of three fasteners on each side of the mounting plate. For

models PP351 and PP451, mount using a minimum of two fasteners on each side of the

mounting base. If necessary to prevent damage from water leakage, you should also have seal-

ant (not supplied) to apply around the bolt holes between the mount and mounting surface.

Summary of content (4 pages)

PAGE 1
C212M-B (8/04) PP350/PP450 Parapet Mount PP351/PP451 Rooftop Mount ® 3500 Pelco Way, Clovis, CA 93612-5699 USA IMPORTANT SAFEGUARDS AND WARNINGS In North America & Canada: Tel (800) 289-9100 FAX (800) 289-9150 1. Installation and servicing should only be done by qualified service personnel and conform to all local codes. 2. Installation shall be done in accordance with all local and national electrical and mechanical codes utilizing only approved materials. 3.
PAGE 2
Installing the Mount 1. Loosen the nuts holding the brake mounting plate. Loosen the nuts only enough to pull the arm out of the guide hoops (see Figure 1). 2. Remove the arm. 3. Install the mount. PP350/PP450 Install the mounting plate to the inside or the outside of the parapet. Use a minimum of three fasteners on each side of the mounting plate. Depending on the type of parapet construction, install the mounting plate as close to the top of the parapet as possible.
PAGE 3
SPECIFICATIONS Material: Aluminum Mounting Method: 3/8-16 fasteners; minimum of 6 for PP350/PP450; minimum of 8 for PP351/PP451 Maximum Load: 45 lb (20.41 kg) Dimensions: See Figure 2 Finish: Gray polyester powder coat Weight PP350: PP351: PP450: PP451: 9.30 lb (4.22 kg) 20.19 lb (9.16 kg) 10.38 lb (4.71 kg) 22.53 lb (10.22 kg) (Design and product specifications subject to change without notice.) Figure 2.
PAGE 4
WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex® Series products (multiplexers, server, and keyboard).