I N S T A L L A T I O N ® FT8301/FR8301 Fiber Transmitter and Receiver Single-Channel Digitally Encoded Video C1641M-A (3/05)
Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Product Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other that contained in the operating instructions unless you are qualified to do so. The product and/or manual may bear the following marks: This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit.
Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules.
Product Overview DESCRIPTION The FT8301/FR8301 fiber transmitter and receiver provide the ability to transmit one composite video channel over one optical fiber (refer to Figure 1). ONE VIDEO INPUT FT8301 TRANSMITTER ONE FIBER FR8301 RECEIVER ONE VIDEO OUTPUT Figure 1.
MODELS The FT8301/FR8301 fiber transmitter and receiver consist of the following series of models: Multimode Models: FT8301MST Single-channel fiber optic video transmitter; multimode, ST connector; transmission distance up to 2 km FR8301MSTR Single-channel fiber optic video receiver; multimode, ST connector; transmission distance up to 2 km FT8301MSTE Single-channel fiber optic video transmitter; multimode, ST connector; transmission distance up to 6 km (extended distance) FR8301MSTRE Single-channel
FRONT PANEL The front panel of the FT8301 transmitter and the FR8301 receiver provides LED indicators that allow you to monitor signal status and operating power. The following sections provide a view of the front panel of the FT8301 transmitter and the FR8301 receiver. FRONT PANEL - FT8301 TRANSMITTER Figure 2 illustrates the front panel of the FT8301 transmitter. Figure 2.
FRONT PANEL - FR8301 RECEIVER Figure 3 illustrates the front panel of the FR8301 receiver. Figure 3. Front Panel of FR8301 Receiver VIDEO PRESENT LED CARRIER DETECT LED POWER LED (Pelco badge) For detailed information about the front-panel indicators, refer to the Troubleshooting section.
REAR PANEL Connections to the FT8301 transmitter and the FR8301 receiver are made to the rear panel of the modules. The following sections provide a view of the rear panel of the FT8301 transmitter and the FR8301 receiver. REAR PANEL - FT8301 TRANSMITTER Figure 4 illustrates the rear panel of the FT8301 transmitter. 12 /24 Figure 4.
REAR PANEL - FR8301 RECEIVER Figure 5 illustrates the rear panel of the FR8301 receiver. Figure 5.
Installation PACKAGE CONTENTS The following items are supplied: • With the FT8301 transmitter: 1 Regulated switching power supply with four plug adapters (North American, Australian, U.K., and European configurations); 100-240 VAC input, 12 VDC output 1 FT8301/FR8301 Fiber Transmitter and Receiver Installation manual (this manual) • With the FR8301 receiver: 1 Regulated switching power supply with four plug adapters (North American, Australian, U.K.
MOUNTING THE FR8301 RECEIVER The following sections provide information about mounting the FR8301 receiver into a rack or onto a wall. Mounting the FR8301 Receiver into a Rack The FR8301 receiver can be installed into an RK5000 Series rack mount chassis, which can be mounted into an industry-standard 19-inch (48.26 cm) equipment rack.
Mounting the FR8301 Receiver Using the Wall Clip NOTE: Before mounting the FR8301 receiver to a wall, ensure that there is adequate space at both ends for viewing the front-panel LEDs and for making the various rearpanel cable connections. To attach the FR8301 receiver to a wall using the supplied wall clip, refer to Figure 7 and do the following: 1. Using the two vertical or horizontal wall-mounting holes, attach the wall clip to a wall using two screws (not provided). 2.
CONNECTIONS Connections to the FT8301 transmitter and the FR8301 receiver are made on the rear panel of the modules and consist of the following: • Power connection NOTE: A 12 VDC or 24 VAC power supply can be used to power the transmitter/receiver when used as a standalone module. A 12 VDC power supply is provided. If a 24 VAC power supply is used, the power supply must be a Listed Direct Plug-In Power Unit marked as Class 2 and rated as 24 VAC, 200 mA (minimum output).
CONNECTING THE FR8301 RECEIVER Figure 9 illustrates FR8301 receiver connections. POWER/ALARM CONNECTION FOR RACK-MOUNTED MODULE* POWER CONNECTION FOR STANDALONE MODULE† FIBER OPTIC CABLE COAXIAL CABLE *REFER TO THE RK5000PS-3U/RK5000-3U FIBER RACK MOUNT CHASSIS INSTALLATION MANUAL FOR INFORMATION. † †THE STRIPED WIRE OF THE SUPPLIED 12 VDC POWER SUPPLY CONNECTS TO THE PIN 1 SCREW TERMINAL (DC+) OF THE STANDALONE POWER CONNECTOR. THE OTHER WIRE CONNECTS TO THE PIN 2 SCREW TERMINAL (DC-). Figure 9.
Troubleshooting LED indicators on the front panel of the FT8301 transmitter/FR8301receiver (refer to Figure 2 and to Figure 3, respectively) allow you to monitor signal status and operating power. Table A provides information about the front-panel indicators and associated troubleshooting guidelines. Table A. Troubleshooting with Front-Panel Indicators Indicator Color Meaning Possible Cause Corrective Action Power LED (Transmitter) Green Power is being applied – to the module. No action required.
Table A. Troubleshooting with Front-Panel Indicators (Continued) Indicator Color Meaning Possible Cause Corrective Action Video Present LED Green Incoming video signal is present on the channel. Not lit on transmitter Incoming video signal is not present on the channel. Red on receiver Incoming video signal is not present on the channel. – No action required. Video source is not powered on. Check power connection to the video source. Video source is not connected to the transmitter.
Table A. Troubleshooting with Front-Panel Indicators (Continued) Indicator Color Meaning Possible Cause Corrective Action Carrier Detect LED (Receiver Only) Green The optical signal is being received from the transmitter. – No action required. Red The optical signal is not being received from the transmitter. Transmitter is not powered on. Check power connections. Replace power supply if necessary. Fiber optic cable is not connected. Check fiber optic connections.
Specifications VIDEO Number of Channels Modulation Type Video Input Bandwidth Gain Differential Gain Differential Phase Tilt Signal-to-Noise Ratio GENERAL Operating Temperature Input Power Requirements LED Indicators Transmitter Receiver Dimensions Transmitter Receiver Unit Weight Transmitter Receiver MECHANICAL Connectors Video Rack Power/Alarm Standalone Power Fiber Optic 20 1 Pulse code modulation, 8-bit resolution 1.0 Vp-p, 75 ohms; NTSC, PAL, and SECAM 6.
OPTICAL POWER BUDGET, TRANSMISSION DISTANCE, AND LASER CLASS 1 LIMIT Fiber Multimode (62.5/125 µm) Single-mode (9/125 µm) Wavelength Optical Power Budget Maximum Transmission Distance Laser Class 1 Limit* 850 nm 15 dB† 2 km (1.2 mi)†† <0.78 mW 1310 nm † †† 1310 nm 20 dB 20 dB 6 km (3.7 mi) 30 km (18.6 mi) <15.6 mW § <15.6 mW *The FT8301 transmitter/FR8301 receiver is classified by the FDA as a Class 1 laser product.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products and the following fixed camera models: CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and CC3651H-2X.
® Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.
