I N S T A L L A T I O N TW3008AR-4 Active Receiver Eight Channels for UTP Transmission C1668M (8/06)
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC rules.
Description The TW3008AR-4 is an eight-channel active receiver that can receive live video over unshielded twisted pair (UTP) cable. The adaptive technology in the TW3008AR-4 automatically adjusts the low, medium and high frequency components of the video signal allowing for the best possible video transmission. The adaptive technology eliminates the need for manual adjustment by automatically adjusting to provide the most favorable video transmission depending on cable length needed.
PARTS OF THE RECEIVER Figure 1. TW3008AR-4 Parts Status LEDs (8): Light red when there is no UTP video being received. Light green when there is UTP video being received. Flashes amber when Coaxitron pan/tilt/zoom (PTZ) control commands are being transmitted. Distance Dials (8): Override the adaptive technology with the manual selection of cable distance (1,000-4,000 feet or 305-1,219 meters). Auto high mode must be used when connecting to a balun or a Spectra® mini.
Installation Make sure all parts are present for the unit. 1 1 8 4 Universal power supply (Part #PS07-6602-9012G) Power cord (#US-320-C13, #UK-320-C13, #EU-320-C13, or #AU-320-C13) UTP mating connectors Rack mount screws with washers MOUNTING The TW3008AR-4 receiver is 1 rack unit high and can be mounted into a standard EIA 19-inch rack, under a desk/table, or onto a wall. The TW3008AR-4 is shipped with the rack ears on the front, but they can be removed and placed on the center or back of the unit.
SETTING THE DISTANCE DIALS The front of the unit has eight distance dials, one for each channel. The default position for each dial is H (high mode) auto. When the dials are set to H or L (low mode) the adaptive technology in the TW3008AR-4 automatically adjusts the low, medium, and high frequency components of the video signal, allowing for the best possible video transmission. Figure 3.
APPLICATIONS You can connect the TW3008AR-4 active receiver to transmitters, such as the TW3001P passive transceiver, TW3001AT active transmitter, and CC3710/CC3610 UTP cameras. Although you can connect these products using an unshielded twisted pair Cat3 and Cat5 cable, Cat5e and Cat 6 are recommended for the best video performance. Always connect the UTP wires on the Cat cable from + to + and from – to –.
Figure 5 shows a TW3008AR-4 connected to a UTP fixed camera. MONITOR MONITOR MONITOR MONITOR TW 3008AR-4 FIXED CAMERA 12 VDC UNIVERSAL POWER SUPPLY UTP US EU UK PIN 5 + PIN 4 - AU 10 PINS (5-/6+) 8 PINS (4-/5+) Figure 5. TW3008AR-4 Connected to a UTP Fixed Camera Figure 6 shows a TW3008AR-4 connected to a UTP Spectra® for Coaxitron PTZ control. NOTE: Coaxitron control will only work when using BNC A of each channel.
Figure 7 shows a TW3008AR-4 connected to a TW3001P passive transceiver. The TW3001P then connects to a non-UTP fixed camera. MONITOR MONITOR MONITOR MONITOR TW3008AR-4 UTP 12 VDC UNIVERSAL POWER SUPPLY FIXED CAMERA TW3001P US EU UK AU Figure 7. TW3008AR-4 Connected to a Single Passive Transceiver Figure 8 shows a TW3008AR-4 connected to a TW3032P passive transceiver.
Figure 9 shows a TW3008AR-4 connected to a TW3004P passive transceiver. The TW3004P then connects to a non-UTP fixed camera. MONITOR MONITOR MONITOR MONITOR TW3008AR-4 12 VDC UNIVERSAL POWER SUPPLY UTP US EU UK AU 4 3 2 FIXED CAMERA 1 TW3004P Figure 9.
Specifications ELECTRICAL Input Voltage Current Wire Type Wire Category Wire Distance DC Loop Resistance Differential Capacitance Transient Immunity 12 VDC 2.
The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC. This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FR/FT/FS Series fiber optic products and TW3000 Series unshielded twisted pair transmission products. • Three years on Spectra® IV products. • Three years on Genex® Series products (multiplexers, server, and keyboard).
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.