® DD08 Series Intercept® Dome Drive Installation/ Operation Manual C416M-C (1/98) UL ® LISTED Pelco • 300 W. Pontiac Way, Clovis • CA 93612-5699 USA • Pelco Online @ http://www.pelco.
CONTENTS Section Page 1.0 GENERAL .................................................................................................. 5 1.1 IMPORTANT SAFEGUARDS AND WARNINGS ............................... 5 1.2 UNPACKING INSTRUCTIONS .......................................................... 6 1.3 RECOMMENDED TOOLS ................................................................. 6 2.0 DESCRIPTION ........................................................................................... 7 2.1 MODELS ....
REVISION HISTORY Manual # Comments C416M 9/94 Original version. C416M-A 6/95 Revised to incorporate exploded view diagram and BOM changes as per ECO# 94-470; Incorporated white “type E” back box availability; Included hardwire system wiring diagram information. 6/23/95 Addendum. Changed back box wiring diagrams to show 2 A FUS2 fuse as per ECO# 95-063. 9/20/95 Manual revised to include new sound quieting model information, updated hardwire system wiring diagram and related list of materials.
(This page intentionally left blank.
1.0 GENERAL 1.1 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by Qualified Service Personnel and conform to all Local codes. 2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture. 3. Only use replacement parts recommended by Pelco. 4.
1.2 UNPACKING INSTRUCTIONS Unpack and inspect all parts carefully. Be sure to save the shipping carton and any inserts. They are the safest material in which to make future shipments. If an item appears to have been damaged in shipment, replace it properly in its carton and contact the factory at 1-800-289-9100 or 1-559-292-1981 for a replacement. (International customers fax 1-559-348-1120 for authorization and instructions.
2.0 DESCRIPTION The DD08 Series of dome drives is part of the IDS08 Intercept® Series of domes. The IDS08 Series is an integral system that includes a back box (BB08), dome drive (DD08), dome receiver/driver (DRD08), and imager/optics package (IOP08). This manual covers the DD08 Series of dome drives. For installation and operation instructions for the back box, refer to manual C456M-D; for the dome receiver/ driver, refer to C466M-E; and for the imager/optics package, refer to C1441M-C. 2.
3.0 INSTALLATION Proceed with the installation of the dome drive after you have installed the back box. 1. Refer to Figure 6 and remove the shipping bracket (item 37). 2. Refer to the manual for the receiver/driver and set the jumpers and switches as required for your application. 3. DD08C2L and DD08E2L Models Only - The dome drives are capable of 360° rotation. However, pan limit stops have been installed at the factory on the pan gear that limit the rotation to 355°.
BACK BOX HAIRPIN CLIP LATCH GUIDE PIN HAIRPIN CLIP GUIDE PIN LATCH 25-PIN CONNECTOR DOME DRIVE UPPER BRACKET 25-PIN CONNECTOR LATCH PIN LATCH PIN BUSHING BUSHING Figure 2.
NOTE: The tilt limit stops are not adjustable. 7. Turn on the power switch inside the back box. In about 15 seconds, the unit will begin to move and go through its start-up routine. 8. Refer to the manual for the camera/lens to set the switches on the camera as required for your application. 9. DD08C2L and DD08E2L Models Only - If you removed the pan limit stops earlier, skip this step. To adjust the pan limit stops: a. Pan the unit to the desired left position. b.
4.0 MAINTENANCE Regularly scheduled maintenance will prolong the operational life and appearance of the equipment. Clean the dome with a nonabrasive cleaning cloth and antistatic cleaner that is safe for use on acrylic plastic. Do not use kerosene or similar substances that can scratch the surface. The dome drive should also be inspected and any dust and debris blown off. Pay special attention to the gear drives.
5.0 WIRING DIAGRAMS Figure 3.
Figure 4.
Figure 5.
6.0 EXPLODED ASSEMBLY DIAGRAMS 1 2 3 4 8 5 54 6 10 11 7 12 13 48 47 46 24 14 39 22 25 23 21 9 35 45 53 44 43 42 41 15 35 40 38 19 28 49 27 29 31 30 26 34 36 20 33 16 REMOVE BEFORE OPERATING 32 18 17 37 Figure 6.
Table A.
Figure 7.
Table B.
7.0 SPECIFICATIONS MECHANICAL Pan DD08C2L/ DD08E2L models: DD08E3L model: Tilt: Pan and Tilt Speeds: Motors: Connectors Video: Gearing: Bearings Pan: Tilt: Braking Movement in horizontal plane: 0-355° with pan limit stops 360° without pan limit stops 360° -90° movement from horizontal plane The following speeds are available and pre-selected by customer at time of order: Dome Drive Type Pan Speed DD08C2L DD08E2L DD08E3L 24°/sec ± 1° 24°/sec ± 1° Variable (0 – 200°/sec) Tilt Speed 12°/sec ±.
8.0 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one (1) year after the date of shipment. Exceptions to this warranty are as noted below: • • • • • Two (2) years on all standard motorized and fixed focal length lenses. Two (2) years on Legacy®, Intercept®, PV1000 Series, CM6700/CM8500/CM9500/ CM9750/CM9760 Matrix, Spectra™, DF5 Series and DF8 Fixed Dome products.
