user manual

ManualsBrandsPelco ManualsSecurity CameraSecurity Camera MRU

MR4000/MRU

Monitor Mounts

Installation/Operation Manual

C233M-G (8/95)

Pelco • 300 W. Pontiac Way, Clovis, CA 93612-5699 • USA • (800) 289-9100 or (1-559) 292-1981

FAX (800) 289-9150 or (1-559) 292-3827 • DataFax (800) 289-9108 or (1-559) 292-0435

International customers call (1-559) 292-1981 or FAX (1-559) 348-1120

Summary of content (12 pages)

PAGE 1
® MR4000/MRU Monitor Mounts Installation/Operation Manual C233M-G (8/95) Pelco • 300 W.
PAGE 2
CONTENTS Section Page 1.0 GENERAL .................................................................................................. 1 1.1 IMPORTANT SAFEGUARDS AND WARNINGS ............................... 1 2.0 DESCRIPTION .......................................................................................... 2 3.0 INSTALLATION .......................................................................................... 3 3.1 MR4000 ASSEMBLY ................................................................
PAGE 3
LIST OF ILLUSTRATIONS Figure 1 2 3 Page Monitor Assembly .............................................................................. 3 MR4000 Exploded Assembly ............................................................. 6 Dimension Drawings .......................................................................... 7 LIST OF TABLES Table A Page Mechanical Parts List: MR4000/MRU Universal Mounts ...................
PAGE 4
(This page intentionally left blank.
PAGE 5
1.0 GENERAL 1.1 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by Qualified Service Personnel and conform to all Local codes. 2. Installation shall be done in accordance with all local and national electrical and mechanical codes utilizing only approved materials. 3. Use only installation methods and materials capable of supporting four (4) times the maximum specified load.
PAGE 6
2.0 DESCRIPTION The MRU/MR4000 Universal Monitor/Receiver Mounts are engineered to safely mount a monitor/receiver from either a ceiling or a wall. They were designed for use in security systems, educational institutions, churches, hospitals, and other applications requiring flexibility in monitor/receiver mounting and positioning. The MRU/MR4000 will accept monitors/receivers from 19-31 inches (48.26-78.74 cm) wide.
PAGE 7
3.0 INSTALLATION Installation instructions for the MR4000 and MRU universal monitor/receiver mounts are divided into two sections. Follow the steps outlined in order to assure a proper set-up. 3.1 MR4000 ASSEMBLY 3.1.1 Monitor Assembly (See Figure 1) 1. Determine the location of the monitor mounting brackets. It will be most convenient to mount the brackets to the bottom of the monitor in place of the rubber “feet”. 2.
PAGE 8
3.1.3 Mounting the Hanger Assembly NOTE: When determining the mounting location, consideration must be given to the total weight of the monitor and the mount. The mounting surface must be adequate to support this weight. 1. Determine the location for, and the type of mount to be used. Remember to allow for adequate clearance on all sides of the monitor. 2. Use the adapter mount as a template to mark the required mounting holes. 3.
PAGE 9
3.2 MRU ASSEMBLY INSTRUCTIONS 3.2.1 Hanger Assembly 1. Fit together the top bracket and the two side arms and place over the monitor/ receiver. Adjust each side arm equally outward to align the fastener holes. Using the four (4) 1/4-20 x 5/8 hex bolts, flat washers, lock washers and hex nuts supplied, fasten the arms to the top bracket. 2. Remove the monitor from the hanger assembly. 3.
PAGE 10
4.0 EXPLODED ASSEMBLY An exploded assembly diagram for the MR4000 is shown in Figure 2. Items noted with an asterisk in the parts list (Table A) are parts used for the MRU mount. Figure 2. MR4000 Exploded Assembly Table A. Mechanical Parts List: MR4000/MRU Universal Mounts Item No.
PAGE 11
5.0 SPECIFICATIONS Construction: Steel Finish: Polyester powder coat Maximum Load: 150 lbs (68 kg) Dimensions: See Figure 3 Weight: 20 lbs (9 kg) Shipping Weight: 22 lbs (10 kg) MRWA MR4000 MRCA Figure 3.
PAGE 12
6.0 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one (1) year after the date of shipment. Exceptions to this warranty are as noted below: • • • • • Two (2) years on all standard motorized and fixed focal length lenses. Two (2) years on Legacy®, Intercept®, CM8500/CM9500/CM9750 Matrix, Spectra™, DF5 Series and DF8 Fixed Dome products.