I N S T A L L A T I O N SWM Series Wall Mount C293M-C (12/09)
Contents Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Parts List. . . . . . . . . . .
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Only use attachments/accessories specified by the manufacturer. 6. Installation should be done only by qualified personnel and conform to all local codes. 7. Use only installation methods and materials capable of supporting four times the maximum specified load. 8. Only use replacement parts recommended by Pelco. 9.
Description The SWM Series wall mount provides indoor and outdoor wall mounting for Pelco pendant components (domes, back boxes, and adapters) that require a 1.5-inch NPT pipe thread for installation. The mount features cable feedthrough that conceals electrical wiring in the pendant component. Anti-seize lubricant is supplied for application to the pipe threads. The sun shield used for outdoor versions of the pendent component (where available) is readily accepted by the mount.
Installation The SWM can be mounted directly onto a wall, onto a single gang electrical box, or onto a pole using an adapter. Refer to the SWM-PA Series Pole Adapter Installation manual for pole mounting instructions. Refer to the SWM-CA Series Corner Mount Adapter Installation manual for corner mounting instructions. WALL MOUNTING To install the SWM Series wall mount directly onto a wall (refer to Figure 1 on page 7): 1. Determine the location where the mount is to be installed. 2.
9. Attach the pendant component (dome, back box, or adapter) to the mount: a. b. c. d. Pull the electrical cables from the mount into the component. Apply anti-seize lubricant (supplied) to the component pipe threads. Screw the component onto the mount. Complete the installation using the instructions in the component manual. MOUNTING CLEAT MOUNTING FASTENERS (NOT SUPPLIED) WALL MOUNT ADJUSTMENT PLATE 10-24 x 0.625-INCH (1.59 CM) SET SCREW Figure 1.
ELECTRICAL BOX MOUNTING To install the SWM Series wall mount onto a single gang electrical box (refer to Figure 2 on page 9): 1. Thread the two inner mounting holes on the adjustment plate to be used with threaded mounting fasteners (not supplied). 2. Pull the electrical cables from the gang box through the cable hole in the adjustment plate. 3. Fasten the adjustment plate to the mounting surface with two 0.25-inch (M6) diameter fasteners of appropriate length (not supplied). 4.
10. Attach the pendant component (dome, back box, or adapter) to the mount: a. Pull the electrical cables from the mount into the component. b. Apply anti-seize lubricant (supplied) to the component pipe threads. c. Screw the component onto the mount. d. Complete the installation using the instructions in the component manual. MOUNTING CLEAT MOUNTING FASTENERS (NOT SUPPLIED) WALL MOUNT ADJUSTMENT PLATE 10-24 x 0.625-INCH (1.59 CM) SET SCREW Figure 2.
Specifications MECHANICAL Construction Cast aluminum Finish SWM-GY SWM-BK SWM-WT Light gray polyester powder coat Black polyester powder coat White polyester powder coat Mount Method Mount is secured by a set screw to a mounting cleat that is attached to a surface with two fasteners (not supplied). A gasket is affixed to the base to protect the interior from moisture. An adjustment plate is provided to allow the wall mount to be shimmed when the mounting surface is not plumb.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
www.pelco.com Pelco, Inc.
