VBP3000 VIDEO IN A BAG SYSTEM WITH DETACHABLE 5" LCD TV/MONITOR AND VIDEO CASSETTE PLAYER
A. Introduction Thank you for selecting this “Video in a Bag” System. The system's main features include two 5" Liquid Crystal Display (LCD) TV/Monitors and Video Cassette Player (VCP) (see page 4 for a detailed feature list). The system utilizes the latest state of the art electronics and is designed for use in vehicles, hotels, offices or your home. The “Video in a Bag” System is constructed to provide years of reliable, trouble-free service.
INST ALL AT ION INSTRUC INSTALL ALLA INSTRUCTT IONS C. Cautions and Warnings 1. Cleaning Video Head To prevent video head clogging, use only good quality VHS tapes and discard worn out tapes. If the heads become dirty over a period of time during normal operation of the VCP, the picture will be snowy and the auto-tracking will not adjust the picture correctly. We recommend using cleaning cartridges sparingly to restore normal picture. 2.
D. Feature List 1.) One Video Cassette Player with Built In VHF/UHF/CATV Tuner system 2.) Two 5" LCD Monitors with AUX Inputs 3.) One Infra Red Remote Control 4.) One Bag (for carrying the unit and accessories) 5.) One Set of Straps for Mounting 6.) Two Pouches (for the detachable monitors) 7.) One DC Power Adaptor (cigarette lighter adapter) 8.) One AC to DC Power Adapter (two piece set) 9.) Two DIN Cable 10.) One Dipole Antenna 11.) One Slip-on COAX Connector 12.) Two Headphone Jacks Figure 1 E.
2. Refer to Figure 2. For use in a vehicle, take the cigarette lighter socket adapter from the lower compartment, plug one end into the DC IN 12V jack on the rear of the unit, slide the cord through the slot in the bag, and plug the other end into the cigarette lighter socket. Figure 2 F. Powering the Detached Monitor or the Additional Monitor 1.
Note: 1). When the monitor is connected to the main unit the unit will supply inside power to the monitor, there is no need for another power source to be connected to the DC 12V IN jack on the side of the monitor. 2). Refer to Figure 5 and 6. When the monitor is separated (either the monitor detached from the main unit or the additional monitor), You can connect the MONITOR PORT on the side of the monitor to the MONITOR PORT on the rear of the main unit with the supplied DIN cable.
H. Installing the Unit with Bag Between the Driver/Passenger Seat Option 1 (Refer to Figure 7) Figure 7 1. Take one of the supplied straps and connect the latch to the upper metal ring on the left side of the bag. Attach the "S" hook to the same ring after looping the strap around the headrest of the driver's seat. Repeat this process for the right side (Passenger Seat). 2. Take another strap and connect the latch to lower metal ring on the left side of the Bag.
Option 2 (Refer to Figure 8) Figure 8 1. Follow the installation instructions shown in the Option 1. 2. Remove the second monitor and its pouch from the front compartment of the bag. 3. Unfastening the Velcro strap and remove the monitor from the pouch. 4. Rotate the base of the second monitor backward so that it may be placed in an upright position on a flat surface. 5.
Option 3 (Refer to Figure 9) Figure 9 1. Follow the installation instructions shown in the Option 1. 2. Remove the additional monitor and pouch from the front compartment of the bag, make sure to feed the bottom piece of the pouch into the long slot of the Monitor and attach the Velcro strap to fasten the monitor in the pouch. Then loop the strap of the pouch around the headrest and pull the end of the strap while holding the buckle until the pouch is tightly secured. 3.
I. Installing the Unit with Bag on the Back Seat in a Car There is no need to remove the four straps from the bag as they are not used in this installation. Option 1 (Refer to Figure 10). Figure 10 Carefully place the system (back facing up) on the back seat. Guide the vehicles safety belt through the short strap sewn on the front of the bag. Then secure and adjust the safety belt so that the unit is not free to move around.
3. Remove the additional monitorand pouch from the front compartment of the bag, making sure to feed the bottom piece of the pouch into the long slot of the monitor and attach the Velcro strap to fasten the monitor in the pouch. Then loop the strap of the pouch around the headrest of the same row, and pull the end of the strap when holding the buckle until the pouch is tightly secured. 4. Insert one end of the DIN cable into the MONITOR PORT on the side of the detached monitor.
K. Controls/Jacks/Plug/Indicator (Refer to Figure 13) Figure 13 1. Headphone Input Jack 2. 12V DC Input Jack for Monitor 3. Remote Control Sensor 4. Power LED Indicator for Monitor 5. Power Switch for Monitor 6. TV/VCP Select Switch 7. Brightness Up/Down Thumbwheel 8. Volume Up/Down Thumbwheel 9. Audio R Input Jack 10. Audio L Input Jack 11. Video Input Jack 12. Monitor Port (Input) 13. Release Button for Monitor 14. Power Button for VCP 15. Stop/Eject Button 16. Auto Repeat Button 17.
L. Remote Control (Refer to Figure 14) 1. TV Power Button 2. Number Buttons 3. Skip Search Button 4. TV/CATV Select Button 5. VCP Power Button 6. (Fast) Rewind Button 7. (Fast) Forward Button 8. TV Channel Up Button 9. TV Channel Down Button 10. Auto Memory Button 11. Erase/Write Button 12. Play Button 13. Stop/Eject Button 14. Pause Button Figure 14 M. Watching a Movie 1. With power applied to the unit, select the VCP mode by sliding the TV/VCP switch on the face of the monitor to the TV/VCP position.
N. Watching TV 1. Antenna a. Refer to Figure 15. Plug the dipole antenna into the reserve hole on the back of the system with its side that connects the cable facing up, you will hear a snap as it locks into place. Plug its connector into the RF IN jack. Extract the dipole antenna and adjust its extension, angulation and direction to optimize the picture and sound. Figure 15 b. If there is poor reception of signals with the dipole antenna, connect an external antenna or the CATV to the antenna jack. 2.
P. Wired Headphone Optional wired headphones may be used with the "Video In a Bag" System. Simply plug in the headset to the headphone jack on the side of the monitor, and both internal speakers will be turned off. Q. Support External Monitors Contact an authorized Audiovox dealer for information on ordering an additional external monitors (max number of two external monitors can be supported). Using the DIN cable, connect the external monitor to the MONITOR PORT on the rear of the main unit.
OPER AT ING INSTRUC INSTRUCTT IONS 90 DAY LIMITED WARRANTY AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 90 days from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned product (at the Company's option) without charge for parts and repair labor.
