User manual
Table Of Contents
- CONTENTS
- 1.0 GENERAL
- 1.1 SAFEGUARDS, WARNINGS, CAUTION, AND CARE
- 1.2 REGULATORY NOTICES
- 1.3 UNPACKING INSTRUCTIONS
- 2.0 OVERVIEW
- 2.1 INTRODUCTION TO TIME-LAPSE RECORDERS
- 2.2 TLR2096 FEATURES AND FUNCTIONS
- 3.0 QUICK START
- 3.1 BASIC START
- 3.2 ADDITIONAL ITEMS
- 4.0 INSTALLATION
- 4.1 PRE-INSTALLATION CAUTIONS
- 4.1.1 Securing The VCR Controls
- 4.1.2 Monitor Tips
- 4.2 INSTALLATION
- 4.3 CONNECTING THE VCR TO A MULTIPLEXER
- 5.0 CONTROLS
- 5.1 FRONT PANEL
- 5.2 FLUORESCENT DISPLAY
- 5.3 REAR PANEL
- 6.0 PROGRAMMING
- 6.1 GENERAL PROGRAMMING INSTRUCTIONS
- 6.2 QUICK GUIDE TO TLR2096 MENU STRUCTURE
- 6.3 MAIN MENU
- 6.4 DISPLAY MENU
- 6.4.1 Display Mode
- 6.4.2 Time Date Size
- 6.5 TIME DATE SEARCH MENU
- 6.6 TIMER PROGRAM MENU
- 6.7 RECORDING SET UP MENU
- 6.8 REAR TERMINAL MENU
- 6.9 MAINTENANCE MENU
- 6.10 FIRST TIME SET UP MENU
- 6.10.1 Day And Time Display Modes
- 6.10.2 Set The Day And Time
- 7.0 LOADING/UNLOADING/PROTECTING THE TAPE CASSETTE
- 7.1 LOADING
- 7.2 UNLOADING
- 7.3 PREVENTING ACCIDENTAL ERASURE
- 8.0 RECORDING
- 8.1 MANUAL RECORDING
- 8.1.1 Recording Mode
- 8.1.2 Record Check Function
- 8.1.3 Audio Recording
- 8.1.4 Repeat Recording
- 8.1.4.1 Number Of Tape Uses (Repeat Recording Times)
- 8.1.4.2 Recommended Number Of Tape Uses
- 8.1.5 Series Recording
- 8.1.6 Synchronous Recording
- LIST OF TABLES
- LIST OF ILLUSTRATIONS
- 1 Typical System Setup
- 2 Connecting VCR To Multiplexer
- 3 Front View
- 4 Fluorescent Display
- 5 Rear View
- 6 Not Used
- 7 Menu Tree
- 8 Main Menu
- 9 Display Menu
- 10 Time Date
- 11 Timer Program Illustration
- 12 Recording Set
- 13 Rear Terminal
- 14 Maintenance
- 15 First Time Set
- 16 Display Mode 1
- 17 Display Mode 2
- 18 Manual Recording Steps
- 19 Connecting VCRs in Series
- 20 Synchronous Recording Sequence
- 21 Connection For Synchronous Recording
- 22 Switching From Normal To Alarm Mode And Back
- 23 Alarm Recording Connection
- 24 Time Clock Adjustment Connection
- 25 Playback Controls
- 26 Shuttle Ring Speed Settings
- 27 Direct Shuttle Ring Speed Settings
- 28 Index Searching
- 29 Skip Searching
- 30 Tracking Adjustment
- 31 Picture Quality Adjustment
- 32 Vertical Picture Adjustment
- 8.2 TIMER RECORDING
- 8.2.1 Programming Procedure
- 8.2.2 Special DW Settings
- 8.2.3 Avoid Mistakes When Using The Timer
- 8.3 ALARM RECORDING
- 8.3.1 Alarm Recording Connection
- 8.3.2 External Time Clock Adjustment
- 8.3.3 Programming For Alarm Recording
- 8.3.4 Emergency Recording
- 8.3.5 Alarm Record Time Display
- 8.3.5.1 Reset The Alarm Recording List
- 8.4 RECORDING AFTER A POWER FAILURE
- 9.0 PLAYBACK
- 9.1 PLAYBACK PROCEDURE
- 9.1.1 Playback Mode
- 9.1.2 Audio Playback
- 9.1.3 End Of Tape
- 9.2 SPECIAL EFFECTS PLAYBACK
- 9.2.1 Shuttle Ring
- 9.2.2 Direct Shuttle Ring
- 9.2.3 Still Picture
- 9.2.4 Frame-By-Frame Playback
- 9.3 Locating The Start Of Alarm Recordings
- 9.3.1 Index Search
- 9.3.2 Skip Search
- 9.4 ADJUSTMENT DURING PLAYBACK
- 9.4.1 Tracking Adjustment
- 9.4.2 Picture Quality Adjustment
- 9.4.3 Vertical Adjustment
- 10.0 ADDITIONAL FUNCTIONS AND FEATURES
- 10.1 COUNTER
- 10.1.1 Counter Memory
- 10.1.2 Tape Counter
- 10.1.3 Counter Reset
- 10.2 MEMORY BACKUP IN CASE OF POWER FAILURE
- 10.3 POWER FAILURE TIME DISPLAY
- 10.4 ELAPSED TIME DISPLAY
- 11.0 TESTING
- 11.1 INITIAL SYSTEM TESTING
- 11.2 REGULAR SYSTEM TESTING
- 12.0 TROUBLESHOOTING
- 12.1 SELF-DIAGNOSTIC FUNCTION AND WARNING DISPLAY
- 12.2 BEFORE CALLING FOR SERVICE
- 13.0 SPECIFICATIONS
![](/manual/pelco/vcr-tlr2096/user-manual-english/images/img-14.png)
14 Pelco Manual C651M (7/99)
4.3 CONNECTING THE VCR TO A MULTIPLEXER
Figure 2 shows how to connect the VCR to an MX4000 Series Genex™ Multi-
plexer.
• For Automatic Speed Tracking (“B” lines in Figure 2)
This lets the VCR control the multiplexer’s recording speed. It is the most
efficient recording method.
1. Connect the VCR’s CLK output to the multiplexer’s head switching (HS)
input to synchronize camera switching.
2. Connect the multiplexer’s ground terminal to the VCR’s GND terminal.
• For Alarm Recording (“A” lines in Figure 2)
This is to start and stop recording when there are alarms.
1. Connect the multiplexer’s normally open (NO) relay terminal to the VCR’s
SET IN (alarm input) terminal.
2. Connect the multiplexer’s common C terminal to the VCR’s GND terminal.
NOTE:
Cameras and monitors are
connected to the multiplexer. Fig-
ure 2 shows the connection be-
tween the VCR and an MX4000
Series Genex™ Multiplexer. Refer
to the multiplexer manual for addi-
tional component connections.
Figure 2. Connecting VCR To Multiplexer
VCR
AUX
MAIN
SPOT
SVHS
OUT IN
SVHS
IN COM OUT
NN
H
OC
C
S
120 VAC 60 Hz
ALARMS
1 2 3 4 5 67 8 91011 14151612 13
MX4000 GENEX™ SERIES MULTIPLEXER
TIME-LAPSE VCR
REMOTE
RESET
IN
GND
CLK
AUDIO
VIDEO
IN OUT
CALL
OUT
OUT
MIC
ALM
IN
RECSET RST
MODE
A
B
COAXIAL CABLE
COAXIAL CABLE