User manual
Table Of Contents
- CONTENTS
- 1.0 GENERAL
- 1.1 SAFEGUARDS, WARNINGS, CAUTION, AND CARE
- 1.2 REGULATORY NOTICES
- 1.3 UNPACKING INSTRUCTIONS
- 2.0 OVERVIEW
- 2.1 INTRODUCTION TO TIME-LAPSE RECORDERS
- 2.2 TLR2096 FEATURES AND FUNCTIONS
- 3.0 QUICK START
- 3.1 BASIC START
- 3.2 ADDITIONAL ITEMS
- 4.0 INSTALLATION
- 4.1 PRE-INSTALLATION CAUTIONS
- 4.1.1 Securing The VCR Controls
- 4.1.2 Monitor Tips
- 4.2 INSTALLATION
- 4.3 CONNECTING THE VCR TO A MULTIPLEXER
- 5.0 CONTROLS
- 5.1 FRONT PANEL
- 5.2 FLUORESCENT DISPLAY
- 5.3 REAR PANEL
- 6.0 PROGRAMMING
- 6.1 GENERAL PROGRAMMING INSTRUCTIONS
- 6.2 QUICK GUIDE TO TLR2096 MENU STRUCTURE
- 6.3 MAIN MENU
- 6.4 DISPLAY MENU
- 6.4.1 Display Mode
- 6.4.2 Time Date Size
- 6.5 TIME DATE SEARCH MENU
- 6.6 TIMER PROGRAM MENU
- 6.7 RECORDING SET UP MENU
- 6.8 REAR TERMINAL MENU
- 6.9 MAINTENANCE MENU
- 6.10 FIRST TIME SET UP MENU
- 6.10.1 Day And Time Display Modes
- 6.10.2 Set The Day And Time
- 7.0 LOADING/UNLOADING/PROTECTING THE TAPE CASSETTE
- 7.1 LOADING
- 7.2 UNLOADING
- 7.3 PREVENTING ACCIDENTAL ERASURE
- 8.0 RECORDING
- 8.1 MANUAL RECORDING
- 8.1.1 Recording Mode
- 8.1.2 Record Check Function
- 8.1.3 Audio Recording
- 8.1.4 Repeat Recording
- 8.1.4.1 Number Of Tape Uses (Repeat Recording Times)
- 8.1.4.2 Recommended Number Of Tape Uses
- 8.1.5 Series Recording
- 8.1.6 Synchronous Recording
- LIST OF TABLES
- LIST OF ILLUSTRATIONS
- 1 Typical System Setup
- 2 Connecting VCR To Multiplexer
- 3 Front View
- 4 Fluorescent Display
- 5 Rear View
- 6 Not Used
- 7 Menu Tree
- 8 Main Menu
- 9 Display Menu
- 10 Time Date
- 11 Timer Program Illustration
- 12 Recording Set
- 13 Rear Terminal
- 14 Maintenance
- 15 First Time Set
- 16 Display Mode 1
- 17 Display Mode 2
- 18 Manual Recording Steps
- 19 Connecting VCRs in Series
- 20 Synchronous Recording Sequence
- 21 Connection For Synchronous Recording
- 22 Switching From Normal To Alarm Mode And Back
- 23 Alarm Recording Connection
- 24 Time Clock Adjustment Connection
- 25 Playback Controls
- 26 Shuttle Ring Speed Settings
- 27 Direct Shuttle Ring Speed Settings
- 28 Index Searching
- 29 Skip Searching
- 30 Tracking Adjustment
- 31 Picture Quality Adjustment
- 32 Vertical Picture Adjustment
- 8.2 TIMER RECORDING
- 8.2.1 Programming Procedure
- 8.2.2 Special DW Settings
- 8.2.3 Avoid Mistakes When Using The Timer
- 8.3 ALARM RECORDING
- 8.3.1 Alarm Recording Connection
- 8.3.2 External Time Clock Adjustment
- 8.3.3 Programming For Alarm Recording
- 8.3.4 Emergency Recording
- 8.3.5 Alarm Record Time Display
- 8.3.5.1 Reset The Alarm Recording List
- 8.4 RECORDING AFTER A POWER FAILURE
- 9.0 PLAYBACK
- 9.1 PLAYBACK PROCEDURE
- 9.1.1 Playback Mode
- 9.1.2 Audio Playback
- 9.1.3 End Of Tape
- 9.2 SPECIAL EFFECTS PLAYBACK
- 9.2.1 Shuttle Ring
- 9.2.2 Direct Shuttle Ring
- 9.2.3 Still Picture
- 9.2.4 Frame-By-Frame Playback
- 9.3 Locating The Start Of Alarm Recordings
- 9.3.1 Index Search
- 9.3.2 Skip Search
- 9.4 ADJUSTMENT DURING PLAYBACK
- 9.4.1 Tracking Adjustment
- 9.4.2 Picture Quality Adjustment
- 9.4.3 Vertical Adjustment
- 10.0 ADDITIONAL FUNCTIONS AND FEATURES
- 10.1 COUNTER
- 10.1.1 Counter Memory
- 10.1.2 Tape Counter
- 10.1.3 Counter Reset
- 10.2 MEMORY BACKUP IN CASE OF POWER FAILURE
- 10.3 POWER FAILURE TIME DISPLAY
- 10.4 ELAPSED TIME DISPLAY
- 11.0 TESTING
- 11.1 INITIAL SYSTEM TESTING
- 11.2 REGULAR SYSTEM TESTING
- 12.0 TROUBLESHOOTING
- 12.1 SELF-DIAGNOSTIC FUNCTION AND WARNING DISPLAY
- 12.2 BEFORE CALLING FOR SERVICE
- 13.0 SPECIFICATIONS
Pelco Manual C651M (7/99) 19
6.0 PROGRAMMING
6.1 GENERAL PROGRAMMING INSTRUCTIONS
The following is a universal procedure that shows how programming is done on the
VCR. Use the JOG dial to select items, the SHUTTLE ring to the right to enter,
and SHUTTLE ring to the left to exit.
1. Press the DISPLAY button. The Main menu is displayed.
2. Turn the JOG dial to select the desired item.
• Turn it to the right to move the cursor downward.
• Turn it to the left to move the cursor upward.
3. Turn the SHUTTLE ring to the right. The desired item is selected and the
menu will appear.
4. Turn the JOG dial to select an item.
5. Turn the SHUTTLE ring to the right. The item will flash.
6. Turn the JOG dial to change the setting.
7. Turn the SHUTTLE ring to the right to enter.
8. Press the DISPLAY button. The present time display will appear.
Note:
If the VCR is connected to
an MX4000 Series Genex™ Multi-
plexer, make sure the multiplexer
is in the VCR mode and single-
camera display. Momentarily press
the VIEW button on the multiplexer,
then press the DISPLAY button on
the VCR.