User manual
Table Of Contents
- CONTENTS
- 1.0 GENERAL
- 1.1 SAFEGUARDS, WARNINGS, CAUTION, AND CARE
- 1.2 REGULATORY NOTICES
- 1.3 UNPACKING INSTRUCTIONS
- 2.0 OVERVIEW
- 2.1 INTRODUCTION TO TIME-LAPSE RECORDERS
- 2.2 TLR2096 FEATURES AND FUNCTIONS
- 3.0 QUICK START
- 3.1 BASIC START
- 3.2 ADDITIONAL ITEMS
- 4.0 INSTALLATION
- 4.1 PRE-INSTALLATION CAUTIONS
- 4.1.1 Securing The VCR Controls
- 4.1.2 Monitor Tips
- 4.2 INSTALLATION
- 4.3 CONNECTING THE VCR TO A MULTIPLEXER
- 5.0 CONTROLS
- 5.1 FRONT PANEL
- 5.2 FLUORESCENT DISPLAY
- 5.3 REAR PANEL
- 6.0 PROGRAMMING
- 6.1 GENERAL PROGRAMMING INSTRUCTIONS
- 6.2 QUICK GUIDE TO TLR2096 MENU STRUCTURE
- 6.3 MAIN MENU
- 6.4 DISPLAY MENU
- 6.4.1 Display Mode
- 6.4.2 Time Date Size
- 6.5 TIME DATE SEARCH MENU
- 6.6 TIMER PROGRAM MENU
- 6.7 RECORDING SET UP MENU
- 6.8 REAR TERMINAL MENU
- 6.9 MAINTENANCE MENU
- 6.10 FIRST TIME SET UP MENU
- 6.10.1 Day And Time Display Modes
- 6.10.2 Set The Day And Time
- 7.0 LOADING/UNLOADING/PROTECTING THE TAPE CASSETTE
- 7.1 LOADING
- 7.2 UNLOADING
- 7.3 PREVENTING ACCIDENTAL ERASURE
- 8.0 RECORDING
- 8.1 MANUAL RECORDING
- 8.1.1 Recording Mode
- 8.1.2 Record Check Function
- 8.1.3 Audio Recording
- 8.1.4 Repeat Recording
- 8.1.4.1 Number Of Tape Uses (Repeat Recording Times)
- 8.1.4.2 Recommended Number Of Tape Uses
- 8.1.5 Series Recording
- 8.1.6 Synchronous Recording
- LIST OF TABLES
- LIST OF ILLUSTRATIONS
- 1 Typical System Setup
- 2 Connecting VCR To Multiplexer
- 3 Front View
- 4 Fluorescent Display
- 5 Rear View
- 6 Not Used
- 7 Menu Tree
- 8 Main Menu
- 9 Display Menu
- 10 Time Date
- 11 Timer Program Illustration
- 12 Recording Set
- 13 Rear Terminal
- 14 Maintenance
- 15 First Time Set
- 16 Display Mode 1
- 17 Display Mode 2
- 18 Manual Recording Steps
- 19 Connecting VCRs in Series
- 20 Synchronous Recording Sequence
- 21 Connection For Synchronous Recording
- 22 Switching From Normal To Alarm Mode And Back
- 23 Alarm Recording Connection
- 24 Time Clock Adjustment Connection
- 25 Playback Controls
- 26 Shuttle Ring Speed Settings
- 27 Direct Shuttle Ring Speed Settings
- 28 Index Searching
- 29 Skip Searching
- 30 Tracking Adjustment
- 31 Picture Quality Adjustment
- 32 Vertical Picture Adjustment
- 8.2 TIMER RECORDING
- 8.2.1 Programming Procedure
- 8.2.2 Special DW Settings
- 8.2.3 Avoid Mistakes When Using The Timer
- 8.3 ALARM RECORDING
- 8.3.1 Alarm Recording Connection
- 8.3.2 External Time Clock Adjustment
- 8.3.3 Programming For Alarm Recording
- 8.3.4 Emergency Recording
- 8.3.5 Alarm Record Time Display
- 8.3.5.1 Reset The Alarm Recording List
- 8.4 RECORDING AFTER A POWER FAILURE
- 9.0 PLAYBACK
- 9.1 PLAYBACK PROCEDURE
- 9.1.1 Playback Mode
- 9.1.2 Audio Playback
- 9.1.3 End Of Tape
- 9.2 SPECIAL EFFECTS PLAYBACK
- 9.2.1 Shuttle Ring
- 9.2.2 Direct Shuttle Ring
- 9.2.3 Still Picture
- 9.2.4 Frame-By-Frame Playback
- 9.3 Locating The Start Of Alarm Recordings
- 9.3.1 Index Search
- 9.3.2 Skip Search
- 9.4 ADJUSTMENT DURING PLAYBACK
- 9.4.1 Tracking Adjustment
- 9.4.2 Picture Quality Adjustment
- 9.4.3 Vertical Adjustment
- 10.0 ADDITIONAL FUNCTIONS AND FEATURES
- 10.1 COUNTER
- 10.1.1 Counter Memory
- 10.1.2 Tape Counter
- 10.1.3 Counter Reset
- 10.2 MEMORY BACKUP IN CASE OF POWER FAILURE
- 10.3 POWER FAILURE TIME DISPLAY
- 10.4 ELAPSED TIME DISPLAY
- 11.0 TESTING
- 11.1 INITIAL SYSTEM TESTING
- 11.2 REGULAR SYSTEM TESTING
- 12.0 TROUBLESHOOTING
- 12.1 SELF-DIAGNOSTIC FUNCTION AND WARNING DISPLAY
- 12.2 BEFORE CALLING FOR SERVICE
- 13.0 SPECIFICATIONS
Pelco Manual C651M (7/99) 37
8.3.3 Programming For Alarm Recording
Alarm recording speeds up recording when the VCR is recording in one of the time-
lapse modes. Alarm recording provides more pictures during the alarm. Emergency
recording activates alarm recording even if the VCR is off, stopped, or in timer
recording/standby. You should set the alarm recording mode in the Recording Set
Up menu before using alarm recording.
1. Press the DISPLAY button to display the Main menu.
2. Turn the JOG dial to select RECORDING SET UP and turn the SHUTTLE ring
to the right. The Recording Set Up menu will appear.
3. Turn the JOG dial to select ALARM REC MODE and turn the SHUTTLE ring to
the right.
4. Turn the JOG dial to set the alarm recording mode (2H, 6H, L18H) and turn
the SHUTTLE ring to the right.
5. Turn the JOG dial to select ALARM REC DURATION and turn the SHUTTLE
ring to the right.
6. Turn the JOG dial to set the alarm recording duration from 15 seconds to 10
minutes, MAN1, or MAN2 (manual). Alarm recording will continue for this pe-
riod when an alarm is received. Turn the SHUTTLE ring to the right.
• If the ALARM REC DURATION is set to MAN1, alarm recording will con-
tinue until a signal is received at the RST (reset) IN terminal. If that signal
is within the first 15 seconds of alarm recording, alarm recording will
continue for 15 seconds and then stop.
• If the ALARM REC DURATION is set to MAN2, alarm recording will con-
tinue until the signal received at the SET IN (alarm input) terminal is
removed. If that signal is removed within 15 seconds of the start of alarm
recording, alarm recording will continue for 15 seconds and then stop.
7. Turn the JOG dial to select EMERGENCY REC and turn the SHUTTLE ring to
the right. Turn the JOG dial to select ON.
8. Press the DISPLAY button. The time display will appear.
• During alarm recording, the alarm recording count will be displayed auto-
matically except when Display Mode 4 is selected.
• The alarm recording count display counts up to 9999 alarm recordings
and then resets to 0000 and continues counting.
• When initializing the alarm recording list, the alarm recording count dis-
play will be reset.
• The alarm indicator flashes during alarm recording and lights steadily
when the alarm recording finishes.
• When the alarm recording finishes, the VCR resumes recording in the
same mode as before the alarm recording.
• If you are programming on any of the menus and an alarm input signal is
received at the SET IN (alarm input) terminal, alarm recording will begin
and the menu being programmed will disappear from the screen.
NOTE:
• If an alarm input is received dur-
ing alarm recording, a new alarm
recording will start with the new
input signal. If one alarm input
signal is received within 15 sec-
onds of another, the later alarm
input signal will be ignored and a
new alarm recording will not take
place.
• Alarm recording will continue for
the period set in the ALARM REC
DURATION field, even if a timer
recording has reached its end
time.
• Alarm recording stops when the
end of the tape is reached.
<MAIN MENU >
DISPLAY
TIME DATE SEARCH
TIMER PROGRAM
RECORDING SET UP
REAR TERMINAL
MAINTENANCE
FIRST TIME SET UP
Use JOG to select,
and ENTER.
Press DISPLAY to exit.
<RECORDING SET UP >
ALARM REC MODE 2H
ALARM REC DURATION 1M
EMERGENCY REC ON
<RECORDING SET UP >
ALARM REC MODE 2H
ALARM REC DURATION 1M
EMERGENCY REC ON
<RECORDING SET UP >
ALARM REC MODE 2H
ALARM REC DURATION 1M
EMERGENCY REC ON