User manual
Table Of Contents
- CONTENTS
- 1.0 GENERAL
- 1.1 SAFEGUARDS, WARNINGS, CAUTION, AND CARE
- 1.2 REGULATORY NOTICES
- 1.3 UNPACKING INSTRUCTIONS
- 2.0 OVERVIEW
- 2.1 INTRODUCTION TO TIME-LAPSE RECORDERS
- 2.2 TLR2096 FEATURES AND FUNCTIONS
- 3.0 QUICK START
- 3.1 BASIC START
- 3.2 ADDITIONAL ITEMS
- 4.0 INSTALLATION
- 4.1 PRE-INSTALLATION CAUTIONS
- 4.1.1 Securing The VCR Controls
- 4.1.2 Monitor Tips
- 4.2 INSTALLATION
- 4.3 CONNECTING THE VCR TO A MULTIPLEXER
- 5.0 CONTROLS
- 5.1 FRONT PANEL
- 5.2 FLUORESCENT DISPLAY
- 5.3 REAR PANEL
- 6.0 PROGRAMMING
- 6.1 GENERAL PROGRAMMING INSTRUCTIONS
- 6.2 QUICK GUIDE TO TLR2096 MENU STRUCTURE
- 6.3 MAIN MENU
- 6.4 DISPLAY MENU
- 6.4.1 Display Mode
- 6.4.2 Time Date Size
- 6.5 TIME DATE SEARCH MENU
- 6.6 TIMER PROGRAM MENU
- 6.7 RECORDING SET UP MENU
- 6.8 REAR TERMINAL MENU
- 6.9 MAINTENANCE MENU
- 6.10 FIRST TIME SET UP MENU
- 6.10.1 Day And Time Display Modes
- 6.10.2 Set The Day And Time
- 7.0 LOADING/UNLOADING/PROTECTING THE TAPE CASSETTE
- 7.1 LOADING
- 7.2 UNLOADING
- 7.3 PREVENTING ACCIDENTAL ERASURE
- 8.0 RECORDING
- 8.1 MANUAL RECORDING
- 8.1.1 Recording Mode
- 8.1.2 Record Check Function
- 8.1.3 Audio Recording
- 8.1.4 Repeat Recording
- 8.1.4.1 Number Of Tape Uses (Repeat Recording Times)
- 8.1.4.2 Recommended Number Of Tape Uses
- 8.1.5 Series Recording
- 8.1.6 Synchronous Recording
- LIST OF TABLES
- LIST OF ILLUSTRATIONS
- 1 Typical System Setup
- 2 Connecting VCR To Multiplexer
- 3 Front View
- 4 Fluorescent Display
- 5 Rear View
- 6 Not Used
- 7 Menu Tree
- 8 Main Menu
- 9 Display Menu
- 10 Time Date
- 11 Timer Program Illustration
- 12 Recording Set
- 13 Rear Terminal
- 14 Maintenance
- 15 First Time Set
- 16 Display Mode 1
- 17 Display Mode 2
- 18 Manual Recording Steps
- 19 Connecting VCRs in Series
- 20 Synchronous Recording Sequence
- 21 Connection For Synchronous Recording
- 22 Switching From Normal To Alarm Mode And Back
- 23 Alarm Recording Connection
- 24 Time Clock Adjustment Connection
- 25 Playback Controls
- 26 Shuttle Ring Speed Settings
- 27 Direct Shuttle Ring Speed Settings
- 28 Index Searching
- 29 Skip Searching
- 30 Tracking Adjustment
- 31 Picture Quality Adjustment
- 32 Vertical Picture Adjustment
- 8.2 TIMER RECORDING
- 8.2.1 Programming Procedure
- 8.2.2 Special DW Settings
- 8.2.3 Avoid Mistakes When Using The Timer
- 8.3 ALARM RECORDING
- 8.3.1 Alarm Recording Connection
- 8.3.2 External Time Clock Adjustment
- 8.3.3 Programming For Alarm Recording
- 8.3.4 Emergency Recording
- 8.3.5 Alarm Record Time Display
- 8.3.5.1 Reset The Alarm Recording List
- 8.4 RECORDING AFTER A POWER FAILURE
- 9.0 PLAYBACK
- 9.1 PLAYBACK PROCEDURE
- 9.1.1 Playback Mode
- 9.1.2 Audio Playback
- 9.1.3 End Of Tape
- 9.2 SPECIAL EFFECTS PLAYBACK
- 9.2.1 Shuttle Ring
- 9.2.2 Direct Shuttle Ring
- 9.2.3 Still Picture
- 9.2.4 Frame-By-Frame Playback
- 9.3 Locating The Start Of Alarm Recordings
- 9.3.1 Index Search
- 9.3.2 Skip Search
- 9.4 ADJUSTMENT DURING PLAYBACK
- 9.4.1 Tracking Adjustment
- 9.4.2 Picture Quality Adjustment
- 9.4.3 Vertical Adjustment
- 10.0 ADDITIONAL FUNCTIONS AND FEATURES
- 10.1 COUNTER
- 10.1.1 Counter Memory
- 10.1.2 Tape Counter
- 10.1.3 Counter Reset
- 10.2 MEMORY BACKUP IN CASE OF POWER FAILURE
- 10.3 POWER FAILURE TIME DISPLAY
- 10.4 ELAPSED TIME DISPLAY
- 11.0 TESTING
- 11.1 INITIAL SYSTEM TESTING
- 11.2 REGULAR SYSTEM TESTING
- 12.0 TROUBLESHOOTING
- 12.1 SELF-DIAGNOSTIC FUNCTION AND WARNING DISPLAY
- 12.2 BEFORE CALLING FOR SERVICE
- 13.0 SPECIFICATIONS
40 Pelco Manual C651M (7/99)
9.1.2 Audio Playback
The letter “L” mode (L18H) is for audio recording and playback on the linear track.
Table H. Audio Playback Availability
Playback Mode 2H 6H L18H 72H 96H
Audio Playback Available Available Available Not Available Not Available
Picture Quality Good Good Vibrating Less Vibrating Less Vibrating
NOTES:
• There is normal sound playback
only when a tape recorded in 2H-
L18H modes is played back in its
respective mode.
• If a recording is played back in a
higher mode than that in which it
was recorded, the picture is
played back in slow motion. If
played back in a lower mode than
that in which it was recorded, the
picture is played back in fast mo-
tion.
• The picture may move up/down
or noise may occur when a tape
is played back in L18H, 72H, or
96H mode (even if the tape was
recorded in those modes).
9.1.3 End Of Tape
When the end of the tape is reached, the following functions are performed auto-
matically during playback or fast forwarding.
Table I. End Of Tape Actions
Tape End Selected REPEAT or ALARM•PROT STOP or REWIND
Playback The tape automatically rewinds Stop
to the beginning and stops.
Fast Forward Stop Stop
9.2 SPECIAL EFFECTS PLAYBACK
The VCR features the following convenient functions. Audio output is muted during
special effects playback.
9.2.1 Shuttle Ring
You can use the SHUTTLE ring to adjust the playback speed.
1. Press the PLAY button to begin playback.
2. Press the PAUSE/SHUTTLE HOLD button to get a still picture.
3. Turn the SHUTTLE ring to the appropriate angle for the playback speed you
want.
NOTES:
• Releasing the SHUTTLE ring re-
turns it to the center position and
resumes still mode.
• Pressing the PAUSE/SHUTTLE
HOLD button while turning and
holding the SHUTTLE ring (as in
step 3) continues the playback
speed you selected even though
the SHUTTLE ring is released.
Reverse high speed search
Reverse speed search
Reverse fast playback (x3)
Reverse playback
Reverse slow
Still
15(7)
9(5)
2
1/7
1/15
1/30
1/30
1/15
1/7
9(5)
15(7)
3
Slow playback
Normal playback
Fast playback (x2)
Forward speed search
Forward high speed search
( ) indicates the playback speed of the recorded tape in 2H mode.
Figure 26. Shuttle Ring Speed Settings