User manual
Table Of Contents
- CONTENTS
- 1.0 GENERAL
- 1.1 SAFEGUARDS, WARNINGS, CAUTION, AND CARE
- 1.2 REGULATORY NOTICES
- 1.3 UNPACKING INSTRUCTIONS
- 2.0 OVERVIEW
- 2.1 INTRODUCTION TO TIME-LAPSE RECORDERS
- 2.2 TLR2096 FEATURES AND FUNCTIONS
- 3.0 QUICK START
- 3.1 BASIC START
- 3.2 ADDITIONAL ITEMS
- 4.0 INSTALLATION
- 4.1 PRE-INSTALLATION CAUTIONS
- 4.1.1 Securing The VCR Controls
- 4.1.2 Monitor Tips
- 4.2 INSTALLATION
- 4.3 CONNECTING THE VCR TO A MULTIPLEXER
- 5.0 CONTROLS
- 5.1 FRONT PANEL
- 5.2 FLUORESCENT DISPLAY
- 5.3 REAR PANEL
- 6.0 PROGRAMMING
- 6.1 GENERAL PROGRAMMING INSTRUCTIONS
- 6.2 QUICK GUIDE TO TLR2096 MENU STRUCTURE
- 6.3 MAIN MENU
- 6.4 DISPLAY MENU
- 6.4.1 Display Mode
- 6.4.2 Time Date Size
- 6.5 TIME DATE SEARCH MENU
- 6.6 TIMER PROGRAM MENU
- 6.7 RECORDING SET UP MENU
- 6.8 REAR TERMINAL MENU
- 6.9 MAINTENANCE MENU
- 6.10 FIRST TIME SET UP MENU
- 6.10.1 Day And Time Display Modes
- 6.10.2 Set The Day And Time
- 7.0 LOADING/UNLOADING/PROTECTING THE TAPE CASSETTE
- 7.1 LOADING
- 7.2 UNLOADING
- 7.3 PREVENTING ACCIDENTAL ERASURE
- 8.0 RECORDING
- 8.1 MANUAL RECORDING
- 8.1.1 Recording Mode
- 8.1.2 Record Check Function
- 8.1.3 Audio Recording
- 8.1.4 Repeat Recording
- 8.1.4.1 Number Of Tape Uses (Repeat Recording Times)
- 8.1.4.2 Recommended Number Of Tape Uses
- 8.1.5 Series Recording
- 8.1.6 Synchronous Recording
- LIST OF TABLES
- LIST OF ILLUSTRATIONS
- 1 Typical System Setup
- 2 Connecting VCR To Multiplexer
- 3 Front View
- 4 Fluorescent Display
- 5 Rear View
- 6 Not Used
- 7 Menu Tree
- 8 Main Menu
- 9 Display Menu
- 10 Time Date
- 11 Timer Program Illustration
- 12 Recording Set
- 13 Rear Terminal
- 14 Maintenance
- 15 First Time Set
- 16 Display Mode 1
- 17 Display Mode 2
- 18 Manual Recording Steps
- 19 Connecting VCRs in Series
- 20 Synchronous Recording Sequence
- 21 Connection For Synchronous Recording
- 22 Switching From Normal To Alarm Mode And Back
- 23 Alarm Recording Connection
- 24 Time Clock Adjustment Connection
- 25 Playback Controls
- 26 Shuttle Ring Speed Settings
- 27 Direct Shuttle Ring Speed Settings
- 28 Index Searching
- 29 Skip Searching
- 30 Tracking Adjustment
- 31 Picture Quality Adjustment
- 32 Vertical Picture Adjustment
- 8.2 TIMER RECORDING
- 8.2.1 Programming Procedure
- 8.2.2 Special DW Settings
- 8.2.3 Avoid Mistakes When Using The Timer
- 8.3 ALARM RECORDING
- 8.3.1 Alarm Recording Connection
- 8.3.2 External Time Clock Adjustment
- 8.3.3 Programming For Alarm Recording
- 8.3.4 Emergency Recording
- 8.3.5 Alarm Record Time Display
- 8.3.5.1 Reset The Alarm Recording List
- 8.4 RECORDING AFTER A POWER FAILURE
- 9.0 PLAYBACK
- 9.1 PLAYBACK PROCEDURE
- 9.1.1 Playback Mode
- 9.1.2 Audio Playback
- 9.1.3 End Of Tape
- 9.2 SPECIAL EFFECTS PLAYBACK
- 9.2.1 Shuttle Ring
- 9.2.2 Direct Shuttle Ring
- 9.2.3 Still Picture
- 9.2.4 Frame-By-Frame Playback
- 9.3 Locating The Start Of Alarm Recordings
- 9.3.1 Index Search
- 9.3.2 Skip Search
- 9.4 ADJUSTMENT DURING PLAYBACK
- 9.4.1 Tracking Adjustment
- 9.4.2 Picture Quality Adjustment
- 9.4.3 Vertical Adjustment
- 10.0 ADDITIONAL FUNCTIONS AND FEATURES
- 10.1 COUNTER
- 10.1.1 Counter Memory
- 10.1.2 Tape Counter
- 10.1.3 Counter Reset
- 10.2 MEMORY BACKUP IN CASE OF POWER FAILURE
- 10.3 POWER FAILURE TIME DISPLAY
- 10.4 ELAPSED TIME DISPLAY
- 11.0 TESTING
- 11.1 INITIAL SYSTEM TESTING
- 11.2 REGULAR SYSTEM TESTING
- 12.0 TROUBLESHOOTING
- 12.1 SELF-DIAGNOSTIC FUNCTION AND WARNING DISPLAY
- 12.2 BEFORE CALLING FOR SERVICE
- 13.0 SPECIFICATIONS
Pelco Manual C651M (7/99) 47
11.0 TESTING
11.1 INITIAL SYSTEM TESTING
Before using the newly-installed surveillance system, do the following:
• Make test recordings at the time-lapse speeds you will be using. Test how the
system performs with alarms.
• Interrupt electrical power to check your installed power backup system (if ap-
plicable).
• On playback, verify picture quality and that you can see the time/date display
under normal and alarm conditions.
11.2 REGULAR SYSTEM TESTING
Every day check that the system is operating. Is the REC indicator lit? Does the
COUNTER display indicate movement? Does the monitor show proper camera
sequencing and time/date information?
Check for recorded alarms. Multiple alarms could make the tape run out early.
Make sure there is enough tape to record at least five minutes of alarm activity at
the selected speed.
Regularly verify picture quality and operation under normal and alarm conditions.
Play a tape recorded recently under normal conditions, which also includes an
alarm condition that you triggered manually.
Regularly replace tapes (refer to Table E for a schedule). Check tapes for head
scarring. Replace damaged tapes. Always store tapes in their boxes; away from
magnetic fields, heat, direct sunlight, and dust.