CKT764 CKT774 CKT795 Instructions for use ceramic hob
GB Manual Pictograms used Important information Tip GB 3 - GB 31
CONTENTS Your ceramic hob Introduction Control panel Description GB 4 GB 5 GB 6 What you should pay attention to Connection and repair During use Cooking time limiter GB 7 GB 7 GB 7 GB 9 Safety instructions Use Using the touch controls Pans GB 10 GB 10 Switching on and setting the power Switching off Residual heat indicator Zone function Stand-by mode (Child) lock Pause Kitchen / Egg timer Automatic heat-up function GB 12 GB 12 GB 13 GB 13 GB 14 GB 14 GB 15 GB 16 GB 19 Healthy cooking Cooking setti
YOUR CERAMIC HOB Introduction This hob has been designed for the real lover of cooking. The hob is equipped with ‘Cooklight’ elements. These are very rapid-heating, radiant elements with a high efficiency, which is very favourable for heating-up times. What’s more, these elements also have very good heat distribution. The ample space between the cooking zones makes cooking comfortable. Cooking on a ceramic hob is different from cooking on a traditional appliance.
YOUR CERAMIC HOB Control panel Type CKT764/774 15 13 12 11 11 11 11 10 14 17 16 18 19 20 1 2 5 3 4 6 7 8 9 Type CKT795 15 12 21 11 11 11 11 11 10 14 16 17 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11.
YOUR CERAMIC HOB Description CKT764 CKT774 1 4 5 1 1 6 4 2 CKT795 4 3 1. 2. 3. GB 6 1 7 3 Cooking zone Ø 145 1,2 kW Cooking zone Ø 160 1,5 kW Cooking zone Ø 180 1,8 kW 4. 5. 6. 7.
SAFETY What you should pay attention to • Ceramic cooking is extremely safe. Various devices have been incorporated in the hob such as a residual heat indicator and a cooking time limiter. There are nevertheless a number of precautions you should take. Connection and repair • This appliance may only be connected by a qualified installer. • Never open the casing. The casing may only be opened by an authorized service technician.
SAFETY • Do not allow pans to boil dry. The hob itself is protected against overheating but the pan will get very hot indeed and could be damaged. • The guarantee does not cover any damage caused by an unsuitable pan or a pan boiling dry. • Do not use the cooking area as storage space or worktop. • Ensure that there is several centimetres clearance between the bottom of the hob and the contents of the drawer. • Do not keep anything combustible in the drawer under the hob.
SAFETY Cooking time limiter • The cooking time limiter is a safety function of your cooking appliance. It will operate if you forget to switch off your hob.
USE Using the touch controls The touch controls may take some getting used to if you are used to other (rotary) controls. Place the tip of your finger flat on the control to achieve the best results. You do not have to apply any pressure. Pans Pans for ceramic cooking Ceramic cooking requires a particular quality of pan. Attention • Only use pans that are suitable for electric cooking with: ▷ a thick base (minimum 2.25 mm); ▷ a flat base.
USE Attention • Grains of sand may cause scratches which cannot be removed. Only put pans with a clean base on the cooking surface and always pick pans up to move them. • Always keep the lid on the pan when cooking, in order to avoid energy loss. Tip • Slide the bottom of the pan over a slightly damp cloth, before placing the pan on the cooking zone. This prevents dirt getting on to the cooking surface. • The cooking zone can be switched off 5 to 10 minutes before the end of the cooking time.
OPERATION Switching on the hob and setting the power The power has 9 levels. • Put a pan on a cooking zone. • Touch the On/Off button of the hob. You will hear a short beep and the display for each cooking zone will show ‘0.’. If no further action is taken, the hob will automatically switch off after 10 seconds. • Use the + button or the - button in the desired cooking zone to choose the correct setting. The hob will automatically start in the chosen setting.
OPERATION Attention • The hob saves the latest settings with regard to the extra zone element. When switching the hob on again, the hob will resume using the saved settings. Tip • You can switch off the hob if the (child) lock is set or the pause mode is active. Residual heat indicator A cooking zone that has been used will retain heat for some time after it has been switched off. An ‘H.’ appears in the display as long as the cooking zone is hot.
OPERATION • Touch the + button or - button of the desired cooking zone. Beside the display of the cooking zone, the fish pan zone element icon or the 2nd zone element icon appears. The extra zone element is activated immediately. If the + button or - button is not pressed, the red light to the right of the extra zone element button wil flash for 3 seconds and then turns off. A single beep is heard.
OPERATION (Standard) lock mode Child lock mode The (standard) lock mode prevents settings from being accidentally changed. The child lock mode prevents the hob from being accidentally switched on. All of the set cooking processes remain active. All of the cooking zones and the kitchen timers/egg timers must be set to “0”. Switch the hob to (standard) lock mode One or more cooking zones are active. • Touch and hold the (child) lock button. Attention! All of the set cooking processes remain active.
OPERATION Pause Use the pause function to ‘pause’ the whole hob for 5 minutes while cooking. The power supply to the cooking zone stops, without losing any settings. Please note the cooking zone will remain hot for some time. Preferably remove delicate dishes from the cooking zone. Switching the hob to pause mode One or more cooking zones are active. • Touch the pause button once. ▷ You will hear a single beep.
OPERATION Type CKT764/774 Type CKT795 The kitchen timer The egg timer The kitchen timer must be linked to a cooking zone. This means that the cooking zone switches off when the set time elapses. The egg timer is not linked to a cooking zone. The egg timer continues after the hob has been switched off. Switching on the egg timer The hob is switched on. • Touch the + button and the - button of the kitchen / egg timer simultaneously once. “00.
OPERATION • Use the - button and the + buttons to set the desired cooking time. The kitchen timer can be set until the dot next to the set time disappears. The red light for the kitchen timer of the active cooking zone continues flashing. If you do not use the - button and the + button to set a time, the kitchen timer will automatically switch off after 10 seconds. • Repeat the above steps to set the time for another switched on cooking zone.
OPERATION Automatic heat-up function The automatic heat-up function temporarily increases the power (setting ‘9.’) to heat the contents of the pan faster. This function is available in all settings except setting ‘9.’. Switching on the automatic heat-up function The cooking zone is switched on and active. • Use the + button to select setting ‘A.’ (comes after ‘9.’). ‘A.’ and ‘9.’ flash alternately in the display. • Use the - or the + button to set the desired power. If you select power setting 4, ‘4.
COOKING Healthy cooking Burning point of different types of oil To ensure your food is fried as healthily as possible, Pelgrim recommends choosing the type of oil according to the frying temperature. Each oil has a different burning point at which toxic gasses are released. The below table shows the burning points for various types of oil.
COOKING Cooking settings Because the settings depend on the quantity and composition of the contents of the pan, the table below is intended as a guideline only. Use setting 9 to: • bring the food or liquid to the boil quickly; • ‘shrink’ greens; • heat oil and fat; • bring a pressure cooker up to pressure. Use setting 8 to: • sear meats; • fry flatfish; • fry omelettes; • fry boiled potatoes; • deep fry foods.
MAINTENANCE Cleaning Tip Set the child lock before you start cleaning the hob. Daily cleaning • Best for daily cleaning is a damp cloth with a mild cleaning agent. • Dry with kitchen paper or a dry teacloth. • Special cleaning agents for ceramic hobs have the advantage that a thin film remains on the glass surface so that over-cooked food and lime scale are less likely to get burnt into the hob, making it easier to clean the next time. • It is best to let the hob cool down before cleaning it.
FAULTS General If you notice a crack in the glass top (however small), switch the hob off immediately, unplug the hob, turn off the (automatic) fuse switch(es) in the meter cupboard or, in the event of a permanent connection, set the switch in the power supply lead to zero.) Contact the service department. Troubleshooting table If the appliance does not work properly, this does not always mean that it is defective. Try to deal with the problem yourself first by checking the points mentioned below.
FAULTS GB 24 Symptom Possible cause Solution Spontaneous changing of the cooking setting. - The pan is too close to the touch controls. - Keep the pan at a distance of at least 2 cm from the touch controls. Fault code U400 Overvoltage, 400V appliance connected incorrectly. Connect appliance according to connecting diagram to the bottom of the appliance. Fault code Er36 Control panel overheated, the pan is too close to the touch controls. - Let the hob cool down.
INSTALLATION What you need to consider Safety instructions for the installation • The connection must comply with national and local regulations. • The appliance must always be earthed. • This appliance may only be connected by a competent electrical installer. • For the connection, use an approved cable (for example type HO5RR) in accordance with the regulations. The cable casing should be of rubber. • The connection cable must hang freely and is not to be fed through a drawer.
INSTALLATION Installation dimensions The dimensions and recesses are shown in the illustrations beneath. 643 520 46 480 550 min.50 560 490 CKT764 773 520 46 480 740 min.
INSTALLATION 903 520 46 480 770 min.50 860 490 CKT795 If the hob is wider than the cupboard, with a worktop less than 43 mm thick, saw a cut-out in both sides of the cupboard, so the appliance is detached from the cupboard.
INSTALLATION Electrical connection Common connections: • 3 phases with 1 zero connection (3 1N, 400 V ~ / 50 Hz): ▷ The voltage between the phases and the zero is 230 V ~. The voltage between the phases is 400 V ~. Fit a connecting bridge between connecting points 4-5. Phase 3 carries no load. The groups must have fuses of at least 16 A (3x). The core diameter of the connecting cable must be at least 1.5 mm².
INSTALLATION Building in Check if the cabinet and the cut-out meet the dimension and ventilation requirement. Threat the sawn ends of wooden or synthetic worktops with sealing varnish if necessary, to prevent moisture causing the worktop to swell. Lay the hob upside down on the worktop. Remove the protective layer from the sealing tape and apply the tape in the groove of the aluminium profile or on the edge of the glass plate.
INSTALLATION Technical details This appliance complies with all relevant CE directives. Hob type Ceramic Connection Max.
ENVIRONMENTAL ASPECTS Disposal of packaging and appliance In the manufacturing of this appliance durable materials were used. Make sure to dispose of this equipment responsibly at the end of its lifecycle. Ask the authorities for more information regarding this. The appliance packaging is recyclable. The following may have been used: • cardboard; • polythene film (PE); • CFC-free polystyrene (PS hard foam). Dispose of these materials in a responsible manner and in accordance with government regulations.
GB 32
Het toestel-identificatieplaatje bevindt zich aan de onderkant van het toestel. The appliance identification card is located on the bottom of the appliance. Plak hier het toestel-identificatieplaatje. Stick the appliance identification card here. Houd, wanneer u contact opneemt met de serviceafdeling, het complete typenummer bij de hand. When contacting the service department, have the complete type number to hand.
