Instructions / Assembly

ManualsBrandsPelican Water ManualsKitchen3-Stage Undercounter Drinking Water Filter with Brushed Nickel Dispenser

Pelican Water Systems | www.PelicanWater.com | 877-842-1635

3-Stage Drinking Water Filter

1. Locate and turn o the angle stop valve on the cold water line feeding the sink. This valve

will usually be located under the sink on the pipe coming out of the wall.

2. When the angle stop valve is closed, relieve pressure in the line by momentarily opening

the cold water tap on the sink.

3. Disconnect the cold water faucet feed line at the angle stop valve.

4. Install the feed valve assembly into the angle stop.

5. Firmly press the green 1/4” tubing into the 1/4" connector on the feed valve assembly.

6. Connect the cold water faucet feed line into the feed valve assembly.

7. Make sure the small shut-o valve on the feed valve assembly is closed. Turn on the feed

water connecon valve. Check for leaks.

8. Aach the small feed valve warning tag from the parts bag to the feed valve.

9. Aach the Shuto Warning label to the system so that it is directly visible. Fill out the

Date of Installaon label and aach to the side of the system.

Feed Connecon

Adapter

Shut-o valve

Fig. 1

Note: The feed valve

adapter may be

congured to t either

a 3/8" or 1/2" angle

stop connecon by

changing the locaon

of the adapter.

Angle stop

Summary of content (5 pages)

PAGE 1
® 3-Stage Drinking Water Filter Feed Connection 1. Locate and turn off the angle stop valve on the cold water line feeding the sink. This valve will usually be located under the sink on the pipe coming out of the wall. 2. When the angle stop valve is closed, relieve pressure in the line by momentarily opening the cold water tap on the sink. 3. Disconnect the cold water faucet feed line at the angle stop valve. Shut-off valve 4. Install the feed valve assembly into the angle stop. Adapter 5.
PAGE 2
® 3-Stage Drinking Water Filter Faucet Installation Determine the most practical under-the-sink location for placement of the Pelican 3-Stage Drinking Water Filter. Ensure that the location allows adequate access for cartridge replacement. The faucet installation instructions below are for a standard non-airgap faucet with a quick-connection fitting. 1. Place the system in the selected location. 2. Place the metal escutcheon plate and rubber seal flush against the base of the faucet. 3.
PAGE 3
® 3-Stage Drinking Water Filter Tubing Installation 1. Firmly insert the 3/8" blue tubing from the faucet assembly to the blue coded connector, marked FAUCET, on the top of the system. Make sure the tubing is fully seated. 2. Take the 1/4" green tubing, already connected to the feed water valve, and firmly insert it into the green connector marked FEED. Make sure the tubing is fully seated. 3. The Pelican 3-Stage Drinking Water Filter is now connected and ready for system activation.
PAGE 4
® 3-Stage Drinking Water Filter System Activation and Checklist System Activation and Inspection 1. Check all tubing connections to ensure they are firmly seated. CHECK TO SEE THAT THE CARTRIDGE RETAINER CLIPS ARE PROPERLY INSTALLED WITH SLIDE LOCKS FULLY ENGAGED IN FRAME SLOTS. The retainer clips must be in place during long term, unattended operation of the system. Failure to keep the retaining clips in place could result in accidental leaks and flooding. 2. Open the dispensing faucet at the sink.
PAGE 5
® 3-Stage Drinking Water Filter Maintenance Cartridge Replacement 1. Close the feed water shut-off valve. 2. Open the dispensing faucet. 3. Pull the manifold unit from the installed location. 4. Remove the retaining clip at the front of the unit by pulling back the slide lock and squeezing and pulling to remove. Pull the cartridge off the manifold evenly at top and bottom. Dispose of used cartridge. 5.