Owner Owner’’s Manual Pelican Lite Water Softeners PLS24, PLS48 & PLS80
PLS24, PLS48, PLS80 Water Softeners — Rev A Page 2 © Copyright 2017 Enviro Water Solutions LLC. All rights reserved. All information contained herein is the property of Pelican Water Systems. Pelican Water Systems makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
PLS24, PLS48, PLS80 Water Softeners — Rev A Page 3 Table of Contents Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Product Operation and Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Complete Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
— Rev A Page 4 PLS24, PLS48, PLS80 Water Softeners Product Operation and Specifications Specification Description PLS24 6 GPM Rated Service Flow Minimum Working Pressure 25 PSI Maximum Working Pressure 80 PSI Maximum Vacuum 5 inch/127 mm Hg Operating Temperatures 36°F - 100°F pH Range 6.5 - 11 PLS48 PLS80 12 GPM 18 GPM Important Information Read these instructions carefully and determine the location of all system components before beginning installation.
— Rev A Page 5 PLS24, PLS48, PLS80 Water Softeners Complete Parts List Note: Enviro Water Solutions supplies the parts below to accommodate a variety of water supply lines. Table 1: Parts List Part Description Bypass Valve for Electronic Head Qty. Part 1 Description 1" PVC Tail Adaptor for Electronic Head Bypass Qty. 2 90 degree 1" PVC Tail Adaptors also included PVC Tubing Drain Line (50 ft.) 1 Brine Tank 1 Electronic Head 1 Softener Tank 1 M EN U SE T Note: Drawings are not to scale.
OPTIONAL BYPASS ** MENU SET SHUT OFF VALVES HOSE SPIGOTS ** BACKWASH LINE TO BE PLUMBED TO A DRAIN P Pelican Water Systems 3060 PERFORMANCE CR SUITE 2 DELAND, FL 32724 DO NOT SCALE DRAWING THIS DRAWING IS ISSUED IN CO NFIDENCE AND CANNO T BE REPRO DUCED O R USED TO MANUFACTURE ANYTHING SHO WN O R REFERRED TO WITHO UT DIRECT WRITIEN PERMISSIO N FROM PELICAN WATER SYSTEMS.
— Rev A Page 6 PLS24, PLS48, PLS80 Water Softeners Installation Overview Wall Incoming Water Supply Bypass Valve Drain Line Barb Outgoing Water to House Safety Valve Electronic Head Brine Tank Top View Softener Tank Figure 1 Pre-Installation Bypass Valve Installation Front View Bypass Valve Red Clip Electronic Head Softener Tank Figure 2 If the Red Clips are in the slots (female opening of Electronic Head) remove them.
— Rev A Page 7 PLS24, PLS48, PLS80 Water Softeners Notice: The Bypass Valve on the Electronic Head can be set to Bypass or Service by turning the knobs on the top of the valve. The valves can be difficult to turn by hand until the seals become saturated. Use the supplied Bypass Allen Wrench to turn the knobs if necessary. IMPORTANT! Do not remove the red clips from the Bypass Valve after connecting to main water supply.
— Rev A Page 8 PLS24, PLS48, PLS80 Water Softeners Installation Install Electronic Head MENU SET Electronic Head Red Clips Distributor Tube Bypass Valve Tail Adaptors Figure 3 1. Level the Softener Tank. Notice: If the tank is not level, lift the tank straight up 6 inches and tap it on the ground until the tank stands vertical. The bottom of the tank is round and the boot allows the tank to stand upright. 2.
— Rev A Page 9 PLS24, PLS48, PLS80 Water Softeners Final Setup and Installation Wall Incoming Water Supply Bypass Valve Drain Line Barb Outgoing Water to House Safety Valve Electronic Head Brine Tank Softener Tank Figure 4 9. Attach the black Brine Tank hose to the connection on the top of the Electronic Head by removing the black compression nut. Slide the compression nut over the end of the black tube, fully inserting the Brine Line into the port and tighten the compression nut. 10.
— Rev A Page 10 PLS24, PLS48, PLS80 Water Softeners Programming the Electronic Head Note: Remove protective film from electronic head screen. MENU SET Step 1: Setting the Date & Time 1. 2. 3. 4. 5. Press and hold the MENU button until you hear the beep to unlock. Press MENU button. Press SET once Date & Time Setting is highlighted. Using the UP and DOWN buttons input the correct Date and Time pressing SET after each input. Once set press the MENU button to return to the main menu.
PLS24, PLS48, PLS80 Water Softeners — Rev A Page 11 IMPORTANT! You will need to manually regenerate (Regen Now) your system prior to use. To do so follow the programming below. You will not be able to use water for approximately 2 hours during this process. Step 3: Performing Manual Regeneration 1. Using the DOWN button select Manual Regen and press SET. 2. Using the UP or DOWN button select either Regen Now or Regen Tonight. -Regen Now will start a regeneration process immediately.
— Rev A Page 12 PLS24, PLS48, PLS80 Water Softeners Troubleshooting Problem Solution Water leaking at the top of the tank around the head. You may need to turn the head to tighten it. The tank head is pre-installed hand-tight, do not overtighten the head (just turn it snug). The tank leans to one side or is not level. If the tank is not level, lift the tank straight up 6 inches and tap it on the ground until the tank stands vertical.
PLS24, PLS48, PLS80 Water Softeners — Rev A Page 13 Warranty 5 Year Limited Warranty Enviro Water Solutions warrants to the end user ("customer") that its tanks (13" & smaller), valves, in/out heads, bypass's, fittings, and housings ("Covered Items") will be free from defects in material and workmanship under normal use and service for a period of five years.
— Rev A Page 14 PLS24, PLS48, PLS80 Water Softeners Warranty Registration Form Send in this Warranty Registration Form to validate your warranty. Warranty Registration Form Date Item(s) were Received: Order ID#: Model: Dealer Purchased From: Model/Serial Number: Name: Address: City: State: Zip: Email: Send To: Enviro Water Solutions LLC 3060 Performance Circle, Suite 2 DeLand, FL 32724 Phone: (844) 633-3078 © 2017 Enviro Water Solutions LLC 3060 Performance Circle, Suite 2.