Owner’s Manual Pelican WF6/WF10 Iron/Manganese Filter & Salt Free Softener
Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener Rev T Page 2 © Copyright 2019 Enviro Water Solutions Inc. All rights reserved. All information contained herein is the property of Pelican Water Systems. Pelican Water Systems makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener Rev T Page 3 Table of Contents Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Product Operation and Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Water Conditions for Operation . . . . . . . . . . . .
Rev T Page 4 Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener Product Operation and Specifications Specification Description WF6 WF10 Max Flow Rate 10 GPM 15 GPM Minimum Working Pressure 25 PSI Maximum Working Pressure 80 PSI Maximum Vacuum 5 inch/127 mm Hg Operating Temperatures 36°F – 100°F pH Range 7 - 11 Important Information Read these instructions carefully and determine the location of all system components before beginning installation.
Rev T Page 5 Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener Complete Parts List Note: Pelican supplies the parts below to accommodate a variety of water supply lines. Table 1: Parts List Part Description 1" Plastic Male NPT Assembly: Qty. 2 Description Qty.
Rev T Page 6 Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener Part Description Qty. Pelican Whole House Water Filter 1 Pelican Salt Free Water Softener/Conditioner 1 Part Description Qty. Pelican Whole House Iron & Manganese Filter 1 Note: Drawings are not to scale. Additional fittings will be needed to adapt to your plumbing. © 2019 Enviro Water Solutions, Inc. 3060 Performance Circle, Suite 2, DeLand, FL 32724 www.pelicanwater.
P Water Systems Pelican 0 0 SEDIMENT FILTER 3060 PERFORMANCE CR SUITE 2 DELAND, FL 32724 1-877-842-1635 wm1. pe l i canwater. com **BACKWASH LINE TO BE PLUMBED TO A DRAIN SHUT OFF VALVES 0 0 INJECTION PUMP DO NOT SCALE DRAWING IRON MANGANESE FILTER SET MENU THIS DRAWING IS ISSUED IN CO NFIDENCE AND CANNO T BE REPRO DUCED O R USED TO MANUFACTURE ANYTHING SHO WN O R REFERRED TO WITHO UT DIRECT WRITIEN PERMISSIO N FROM PELICAN WATER SYSTEMS.
Rev T Page 8 Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener Installation Overview Wall Wall Chemical Injector Pump IN OUT Spigot Drain Line Barb Incoming Water Supply Outgoing Water to House OUTLET INLET INLET OUTLET Sediment Filter Solution Tank Electronic Head Whole House Iron & Manganese Filter Whole House Water Filter Salt Free Water Softener/Conditioner Figure 1 Pre-Installation Bypass Valve Installation Bypass Valve Red Arrow Front View INLET Water Filter Head OUTL
Rev T Page Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener Bypass Operation SERVICE BYPASS Bypass Allen Wrench Notice: The Bypass Valve on the Electronic Head can be set to Bypass or Service by turning the knobs on the top of the valve. The valves can be difficult to turn by hand until the seals become saturated. Use the supplied Bypass Allen Wrench to turn the knobs if necessary.
Rev T Page 10 Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener Water Filter - Carbon Soak !IMPORTANT! Your system will not be ready for use for a minimum of 48 hours while the Carbon Soak process takes place. Please plan your installation accordingly. Notice: Water will flow out of the outlet side of the Bypass Valve during this process. Be sure you perform this series of steps in a location suitable for water flow.
Rev T Page 11 Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener Water Filter - Carbon Flush !IMPORTANT! Do not perform the Carbon Flush until the Carbon Soak process is complete. Notice: Water will flow out of the outlet side of the Bypass Valve during this process. Be sure you perform this series of steps in a location suitable for water flow. Bypass Valve Water Garden Hose OUTLET Hose Bib Assembly INLET Carbon Flush Whole House Water Filter Figure 4-1 1.
Rev T Page 12 Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener Installation Sediment Filter Assembly Sediment Filter Cover Sediment Filter O-Ring Blue Filter Housing Stand Pipe Figure 5 1. Unscrew the cover from the Blue Filter Housing. 2. Remove the plastic covering from the Sediment Filter. 3. Place the Sediment Filter onto the Stand Pipe in the Blue Filter Housing and set aside.
Rev T Page 13 Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener Chemical Injector Pump Overview Pressure Release Button Flow Direction Arrow Dosage Adjustment Dosage Lock Nut Suction Hose Nut Figure 7 Pressure Release Button - Allows you to relieve the air pressure after install and maintenance. Flow Direction Arrow - Indicates the proper flow pattern depending on how the unit is install.
Rev T Page 14 Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener Chemical Injector Pump Installation !IMPORTANT! Install the Chemical Injector Pump into the water supply after the Sediment Filter and before any other filtration or softening system. 1. Determine the size and material of your incoming water supply line from the Sediment Filter System. 2. Mount the Chemical Injector Pump to the wall using the provided bracket. Line up the inflow and outflow connections with the current water line.
Rev T Page 15 Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener Iron and Manganese Tank Installation Wall Wall Chemical Injector Pump IN OUT Spigot Drain Line Barb Incoming Water Supply Outgoing Water to House OUTLET INLET INLET OUTLET Sediment Filter Solution Tank Electronic Head Whole House Iron & Manganese Filter Whole House Water Filter Salt Free Water Softener/Conditioner Figure 9 1. Level the Whole House Iron & Manganese Filter.
Rev T Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener Page 16 IMPORTANT! • Ensure the PVC Tubing Backwash Drain Line is not submerged and is free of kinks. • Maximum vertical rise of the backwash line is 6 feet. • If incorporating two or more backwashing systems make sure to keep the drain lines separate. © 2019 Enviro Water Solutions, Inc. 3060 Performance Circle, Suite 2, DeLand, FL 32724 www.pelicanwater.
Rev T Page 17 Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener Whole House Water Filter Installation 1. Level the Whole House Water Filter. Notice: If the tank is not level, lift the tank straight up 6 inches and tap it on the ground until the tank stands vertical. The bottom of the tank is round and the boot allows the tank to stand upright.
Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener Rev T Page 18 3. Install the fitting onto the inlet and outlet sides of the Bypass Valve. Follow the diagram supplied with the fitting. 4. Connect the incoming water supply from the outlet of the Whole House Iron & Manganese Tank to the inlet side of the Pelican Whole House Water Filter. 5. Connect the outgoing water supply to the outlet side of the Bypass Valve.
Rev T Page 19 Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener Whole House Salt Free Water Softener/Conditioner Tank Installation 1. Level the NaturSoft Salt Free Water Softener/Conditioner. Notice: If the tank is not level, lift the tank straight up 6 inches and tap it on the ground until the tank stands vertical. The bottom of the tank is round and the boot allows the tank to stand upright.
Rev T Page 20 Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener NaturSoft - Media Soak Wall Wall Chemical Injector Pump IN OUT Spigot Drain Line Barb Incoming Water Supply Outgoing Water to House OUTLET INLET INLET OUTLET Sediment Filter Solution Tank Electronic Head Whole House Iron & Manganese Filter Whole House Water Filter Salt Free Water Softener/Conditioner Figure 12 CAUTION: The Whole House Water Filter MUST be in the bypass position during this process (see Figure above
Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener Rev T Page 21 Complete the Installation 1. 2. 3. 4. 5. Turn all faucets and spigots off. Press Pressure Release Button on top of Injection Pump. Check for leaks. Peel off the protective plastic wrap from the stainless steel tank jackets. Add the Pelican logo sticker in the desired location on the tank. 6.
Rev T Page 22 Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener Programming the Electronic Head Note: Power Source - For safety reasons the outlet must be protected by a Ground Fault Circuit Interrupter (GFCI). Note: Do not make changes to the settings unless instructed by a Technical Support representative. Your system is pre-set to regenerate every 3 days at 2:00 am, the complete process takes 20 minutes MENU SET Step 1: Setting the Date & Time 1. 2. 3. 4. 5.
Rev T Page 23 Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener Testing Chlorine Levels in Water - Dialing In Pressure Release Button Flow Direction Arrow Dosage Adjustment Dosage Lock Nut Suction Hose Nut Figure 13 1. Put the Whole House Water Filter and NaturSoft tanks into bypass. 2. Turn on the nearest cold water faucet to the system. 3. Listen and watch the pump to make sure it is pumping. The pump should pulse and not run continuously. If the water is off, the pump will stop. 4.
Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener Rev T Page 24 Flush Your Water Heater Cleaning and restoring the plumbing system is a major benefit of the NS3/NS6 NaturSoft system. In order to minimize the time required to complete the de-scaling process, we strongly recommend flushing your water heater after a period of 6 weeks: • Turn off the heat source, attach a hose to the drain valve at the bottom of the tank and flush the heater by opening the drain valve.
Rev T Page 25 Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener If you have a dishwasher: Generally, the NS3/NS6 NaturSoft system removes mineral hardness from solution and forms micro crystals; it does not physically remove the natural minerals from the water. Harsh chemicals, specifically acidic (low pH) detergents or rinse agents, can re-dissolve these crystals. This reduces the desired effect.
Rev T Page 26 Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener Maintenance Sediment Filter It is recommended that the Sediment Filter be replaced every 6-9 months depending on the amount of sediment present in the water supply. If the system has been working properly and the pressure is slowing, it may be time to change the Sediment Filter. Check the Sediment Filter and replace if necessary.
Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener Rev T Page 27 Troubleshooting Problem Solution Water leaking at the top of the tank around the head. You may need to turn the head to tighten it. The tank head is pre-installed hand-tight, do not overtighten the head (just turn it snug). The tank leans to one side or is not level. If the tank is not level, lift the tank straight up 6 inches and tap it on the ground until the tank stands vertical.
Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener Rev T Page 28 Warranty Pelicans Limited Lifetime Warranty Pelican Water ("Pelican") warrants to the end user ("customer") that its tanks (13" and smaller), valves, in/ out non-electric heads, bypass's, fittings and housings for POE systems ("Covered Items") will be free from defects in material and workmanship under normal use and service for a limited lifetime of twelve (12) years from the date of original purchase**.
Rev T Page 29 Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener Warranty Registration Form Send in this Warranty Registration Form to validate your warranty or visit www.PelicanWater.com to complete warranty registration form online.
Rev T Page 30 Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener !IMPORTANT! Do not use where water is microbiologically unsafe or with water of unknown quality without proper disinfection before or after the filter/softener system.
