eDVR Installation Guide MD3200M (v 1.
Caution Since this device is operation purpose and registered as suitable electromagnetic waves, seller or user should be cautios on this point. If the device is sold or purchased wrongly, it is required to replace as Home use. FCC Compliance Statement Caution : Any changes or modifications in construction of this device which are not expressly approved the party responsible for compliance could void the user's authority to operate the equipment.
Important Notice 1. Do not place heavy objects on the top of the eDVR 2. eDVR is for indoor use. It is not weatherproof. Use eDVR with referring to its environmental specifications (Temperature & Humidity). To clean the eDVR, gently wipe the outside with a clean dry cloth. 3. eDVR use AC power of 110V~240V. Be cautions not to cause electric damages to eDVR. 4. Becareful not to drop the eDVR. Physical shocks may harm the products including internal HDD.
Contents OVERVIEW .................................................................................................................................. 7 1. What is MD3200M?.............................................................................................................. 7 2. Supplied accessories.............................................................................................................. 8 3. Description & Function ..............................................................
8.2.7. 8.3. 9. Apply Date/Time .................................................................................................. 22 Setting recording condition ........................................................................................... 23 8.3.1. Configuration Status ............................................................................................. 23 8.3.2. Recording Speed/Quality....................................................................................... 24 8.
12. Using Control Center Lite ................................................................................................ 42 12.1. 12.1.1. Starting.................................................................................................................... 42 PC system requirements for running Control Center Lite.......................................... 42 12.2. Installing Control Center Lite .................................................................................... 42 12.3.
OVERVIEW 1. What is MD3200M? The eDVR MD3200M is a 16-analog channels network digital video recorder. Video, Audio, Text and Event-Logs are digitized and stored on two internal Hard-Drives □ 32 analog video channels □ 4 channel two-way audio recording & playback □ Max.
2. Supplied accessories Unpack and check all the items as below; 1. eDVR MD3200M (1EA) 2. AC Power Cord (1EA) 3. CD (Including Software) (1EA) 4. Remote Controller (1EA) 5. RACK FIXING KIT (1SET) 6. R-HDD screw (8EA) Attention for the system without HDD installed In case of system without HDD, HDD only can only be installed in R-HDD(Removable Hard disk rack). For the internal installation of HDD additionally, For the details, please contact to local distributor.
3.
MD3200M rear (9) AC power connector (10) BNC connector for video input (11) Terminal block for sensor, relay, and serial input/output (12) RS232 connector (13) VGA connector (14) IEEE1394 connector (15) eSATA connector (16) Network Storage connector(RJ45) (17) GND (18) Ethernet connector (19) Audio input/ output connector (20) BNC connector for monitor output 10
INSTALLATION AND CONNECTION 4. Connecting & Running 4.1. Connecting camera (1) Connect CCTV camera to MD3200M with BNC cable as below. 1. The video type for all channels should be either NTSC or PAL, not be combined both. 2. MD3200M sets video signal’s impedance (75Ω ) automatically. 75-Ohm termination register is always connected on video input, and can't be removed. So MD3200M's video input must be a terminal of the connection. 3. Video Type(NTSC/PAL) should be changed after opeting MD3200M.
Monitor out put of MD3200M is separated as A(Normal) and B(Spot). Connect to Monitor A if only one Monitor is used . Monitor output is fixed depend on channel. Video Out 1, 3 is output channel 1 to 16, and Video 2, 4 is output channel 17~32. 4.3. Connecting Audio (1) Connect auto signal to MD3200M with using RCA cable.
4.4. Supplying power (1) Connect power cable as shown below 1. When supplying power, MD3200M starts booting automatically. 2. In order to cut off power, press the power switch on MD3200M front during 4 seconds and enter admin password after appearing a pop window. 3. For supplying again, push the power switch.
5. Running OSD menu 5.1. Using menu Press the [MENU] in keypad of front to open the OSD Configuration Menu ① Main Menu ② Sub-menu ③ Setting Page (1) Main Menu : The selected tab is shown in blue and the related sub-menu will be shown below the tab. To movo to the previous/next Main Menu tab, use the [◀/▶] arrow buttons. To move to a sub-menu, press the [▷]/[▼ ] arrow buttons. (2) Sub-menu : The selected sub-menu is shown in blue and the relaed setting will be shown the right of the sub-menu.
5.2. Dialogue box to edit a word There are two methods to input a word.. (1) Entering words Move pressing [▶] arrow button to enter next word until the word is looking for is shown using [▲ /▼ ] arrow buttons. In case of spacing words, press [▶] to move one space and enter the word. To exit the Dialogue box, press the [▷] arrow button. (2) Available words range to use 1234567890 AB C D E F G H I J K LM N O PQ R ST UVW XYZ abcdefghijklmnopqrstuvwxyz ( ) - .
6. Setting remote controller When controlling several eDVRs with one remote controller, set Remote Contorl ID as follows. 6.1. Setting ID of MD3200M (1) Press the [MENU] button (2) Select “System” with using [▶] button and press the [▷] or [▼ ] button (3) Select “Miscelleaneous” from the sub-menu list using the button[▼ ] and press [▷] button. (4) Select “Remote Control ID” and press the [▷]. (5) Select a value using the [◀/▶] buttons and press the [EXIT] button.
6.2. Selecting MD3200M If several eDVRs are set with unique ID numbers, they can be controlled with one remote controller. To select a specific eDVR (MD3200M), Keep pressing the ID button of remote controller until a buzzer sounds during 2 seconds. Because remote controller ID is sixteen, eDVR will correspond until pressing ID button sixteen times. 6.3. Operable range of remote controller 6.4. Loading the batteries into remote controller Remote Controller requires two AAA-type batteries 1.
7. MD3200M configuration 7.1. Basic configuration 7.2.
7.3. External storage & Back up configuration 7.4.
8. eDVR MD3200M basic setting 8.1. Viewing Image When power is on, MD3200M starts automatically and images are displayed in basic 16ch-split screen after the booting. If user password is set, a prompt for entering the password will appear.
8.2. Setting Date & Time (1) Press [MENU] button and select “Quick Setup” tab. (2) Select “Date/Time” using the [▷] or [▼ ] and press [EXIT] button. 8.2.1. Time Zone (1) Select “Time Zone” using the [◀/▶] or [▲ /▼ ] buton and press [▷] to configure. (2) Select Time Zone using the [◀/▶] button and press [EXIT]. 8.2.2. Daylight Saving (1) Daylight Saving Time is only activated for Time Zone that uses Daylight Savings. (2) Select “Daylight Saving” using the [◀/▶] or [▲ /▼ ] button and press [▷] button.
8.2.4. Time Format (1) Select “Time Format” using the [◀/▶] or [▲ /▼ ] button and press [▷] button.. (2) Two time formats are available; ‘DD/MM/YYYY,’ ‘MM/DD/YYYY’, ‘YYYY/MM/DD’; Select a value using [▲ /▼ ] buttons and press the [EXIT] button when it is finished. (Factory default is set as ‘MM/DD/YYYY’) 8.2.5. Date (1) Select “Date” using the [◀/▶] or the [▲ /▼ ] buttons and press [▷]. Select ‘MM’, ‘DD’, ‘YYYY’ using the [◀/▶] buttons. (2) Press the [EXIT] button when setting is finished. 8.2.6.
8.3. Setting recording condition Recording conditions under the “Quick Setup” menu tab apply the same values to all analog channels 1~16. All settings are applied for 24 hours/ day regardless of the value set for “Time Schedule” or “Alarm Rec.” (1) Press [MENU] button and select “Quick Setup” when OSD menu is shown. (2) Move to sub-menu by pressing [▷] or [▼ ] button. (3) Select “Recording” using the [▲ /▼ ] buttons and press [▷]. 8.3.1. Configuration Status Displays the recording configuration status.
8.3.2. Recording Speed/Quality (1) Select “Recording Speed/ Quality using [▲ /▼ ] buttons and press [▷]. (2) Select a value using the[◀/▶] button. Press the [EXIT] button when it is finished. Recording Speed/Quality means Low : Speed=7.5(6)ips and Quality=Q3 and Resolution=CIF Standard. : Speed=15(12.5)ips and Quality=Q3 and Resolution=Half High : Speed=30(25)ips and Quality=Q5 and Resolution=Half Custom : Speed and Quality = Manually defined by user 8.3.3.
9. Connecting and configuring DIO ports Wire Handling Trimming Wire When connecting a wire to a terminal block, follow the instructions below. Note the different types of wire that can be used. Standard Wire : Peel off the wiring, cover 8~10mm and solder it. Wire gage should be AWG 22~26. Solid Wire : Peel off the wiring cover 8~10mm and solder it. Wire gage should be AWG 20~26 Inserting & removing wire To insert & remove wirte in TERMINAL BLOCK, use a screwdriver in the diagram to the right. 9.1.
9.1.2. Connecting sensor input Connect S1 ~ S16 with referring to the followings. It shows to connect a dry contact (Please refer to “ Wire Handling” on page 27). When connecting a non-dry contact type of sensor (e.g. Open collector output) please contact WEBGATE’s customer Support team.
9.1.3. Configuring sensor at OSD menu (1) Press the[Menu] button and select “Alarm Source”. (2) Press [▷] or [▼ ] button to move to Sub-Menu, select “Sensor” and press [▷]. 9.1.3.1. Global Use when selecting all 16 sensors simultaneously, which can be selected as “Do not use”(Off). “Normal Open” (N.O), and “Normal Close” (N.C.). (1) Select a “Global” and set a type as Off, N.O. or N.C... (2) Press “Apply” to save a configuration 9.1.3.2. Configuration Use when selecting each 16 sensor individually.
1. Configuration a sensor is to set On/Off usage and type. 2. Please refer to “Alarm Rec” for saving and “Alarm Act” for relay-out on the “eDVR User’s Guide” 9.2. Connecting & configuring relay out 9.2.1. Specifications In order to run relay output of eDVR MD3200M normally, the following conditions are required. Spec. 정격 Output Ch. 4Ch relay differential outptus Output type Dry Contact Connecting type Connect the trimmed wire to terminal block DC 24V DC, 1.25A, 30W 125V DC, 0.
9.2.2. Connecting relay out Connect R1 ~ R4 with referring to the followings, It shows to connect a warming light. Please refer to “ Wire Handling” on page 27.
9.2.3. Configuring relay out as OSD menu. Relay can run by sensor or MD and its condition can be set differently according to schedule. When using the [Relay] button + [Number] button on the front panel or Control Center Lite-D S/W, relay can be operated from remote site. Please refer to the “eDVR User’s Guide” for more information.
9.3. Connecting serial port 9.3.1. Configuring serial ports for Pan/Tilt/Zoom The MD3200 series have most major PTZ protocols already pre-programmed. Makes and models not supported can still be controlled using the Transparent Protocol. For a list of supported protocols, refer to the list on the OSD Configuration menu. The following figure shows how to connect PTZ camera to RS485 (COM2). When using another serial port, connect it with referring to each connection diagram below.
9.3.2. Diagram of serial ports 9.3.2.1. Diagram of COM1(RS232) 9.3.2.2. Diagram of COM2/COM4 9.3.2.3.
9.3.3. Configuring Serial Configure PTZ COM ports and available models at “System/ Serial Setup” in MD3200 Series. After completing serial setup, configure base address or port for each channel at “ Camera menu” tab. When connecting PTZ devices to several cameras, be sure base address matches address for the camera.
9.4. Connecting external device with serial port 9.4.1. Connecting text inout device (ATM / POS / Access Control) The MD3200 Series can record text data received from POS/ATM through the COM/RS232 serial port. Connect to COM1/RS232 (9Pin D-Sub) of MD3200M and configure the “Serial Setup” sub-menu under the “System” tab and “Text” sub-menu under the “Alarm Source” tab shown as above figure.
9.4.2. Configuring serial setup (COM1) at OSD menu (1) Set the “System” in OSD menu and move to “Serial Setup” menu. (2) Select COM in “Serial Setup”, set Devices as “Text”. (3) Set Baud Rate/ Parity/ Stop bit with referring to manual of the connected external device.
9.4.3. Configuring text (1) Select the “Alarm Source” menu among OSD menus. (2) Select the “Text” and set each value. Before installing any external device, consult with the local WEBGATE distributor. Some external devices may not be compatible with the eDVR.
9.5. Connecting USB device USB port can be used to copy up to 1 minute of images to a USB Flash memory disk. When connecting USB Device, do not exceed the rated values of USB device as below; USB Spec. Available Device Output Voltage/Current Ver 1.1 (Max 12M bps) USB Memory Stick, Max. 200mA per DC 5V/ Port The disk should be formatted with FAT32 type. If properly connected the disk is recornized automatically as in the following pricutre.
10. Connecting External Storage Extension through NVS04, IEEE 1394b will be supported later. For the details, please contact to local distributor. 10.1. IEEE1394 port MD3200 Series have two IEEE 1394 ports (Rear: 2-ports) for external storage device interface. Some IEEE 1394 Bay may not be recognized by the MD3200 series. Before purchasing consult the local WEBGATE’s local distributor. 10.2.
10.3. Available HDD It is recommended to use following HDD models with the MD3200M. If a non-recommended HDD is used, WEBGATE Inc. will guarantee the warranty. 10.4. Registering & Formating HDD “Disk Manager” will automatically run on start-up installing a HDD as below; If “Disk Manager” deos not automatically run on start-up, make sure the HDD is properly installed. (1) Press [▷] button marked at “Select Disk”. (2) Select new added HDD(indicated as “[F]”) using [▲ /▼ ] button and press [EXIT].
(9) Shut down “Disk Manager” by pressing [EXIT] button. 11. Network monitoring & managing MD3200M can be accessed, controlled, and managed from remote site using PC via Internet/ Intranet, which is same way as local access for controlling & monitoring features. 11.1. Connecting Ethernet (1) Turn off power switch of MD3200M (2) Connect MD3200M to hub with Ethernet cable (3) Turn on power switch of MD3200M 1.
11.2. Configuring Network infomraiton of MD3200M The following description is based on Ethernet connection. For more detailed information on the Network setting page and way of using xDSL, please refer “eDVR USERS’GUIDE”. (1) Press [MENU] button (2) Select “System” using the [◀/▶] buttons and press the [▷] button. (3) Select “Network” using the [▲ /▼ ] buttons and press the [▷] button. (4) Select “IP Addr” using the [▲ /▼ ] and press the [▷] button.
12. Using Control Center Lite Control Center List is a DVR Management Software and it makes DVR installtion & setting more easier throguth a PC which is connected with DVR in Network. All configuration could be handled in OSD menu of DVR without a PC, however, Control Center Lite makes the complete setting more simply. 12.1. Starting To do setting DVR through Control Center Lite, PC and DVR should be connected via Network and installed Contorl Center Lite on the PC. 12.1.1.
3> Select components which wish to install and press “Next” button. “WESP SDK” must be installed. 4>.Click the “Install” button after selecting a directory to be insatalled. 12.3. Log-In Enter User Name, Password and press “Ok” button.
12.4. Configuration Tool Click the icon on the desk top to run “Control Center Lite Configuration Tool”. 12.5. Monitor * Max. 5 users could be connected simultaneously in one unit of MD3200M. Click the icon on the desk top to run “Control Center Lite Monitor”.
12.6. Playback * Max. 2 user could be connected for playback in one unit of MD3200M. Click the icon on the desk top to run “Control Center Lite Playback”.
APPENDIX APPENDIX APPENDIX 46
#1. HDD #1.1. Fundamental notions & terms eDVR storing constructure (VFS2) eDVR series has a peculiar storing constructure, and its features are as follows. (1) It is possible to connect 2 sets of HDD internally (Internal, ATA Interface) and 63 sets of HDD externally (External, 2 ports of IEEE1394 / External, 2 ports of eSATA / Storage Network). (2) All of the connected HDDs are recognized as one virtual disk, and eDVR supports upto 8TB.
(2) HDD Type at Disk Manager [R] Available recording status [V] Connected and formatted as eDVR’s file system. If using ‘Add Used’command, it will be changed to [R]. There is no need to format. [F] Connected but not available eDVR’s file system. After using ‘Add’, need to format for making as [R]. Indicate FAT32 file system connected for backup. [C] CD/DVD-Recorder [X] HDD cable is not connected nor has some problem. In case of that, HDD should be removed with using ‘Confirm Removed’menu.
#1.2. Installing HDD Compatible HDD It is recommended to use the following HDD models with the MD3200M. If a non-recommended HDD is used, WEBGATE Inc. will not guarantee the warranty. Installation and extension of internal HDD-RACK HDD In case of installation/adding or exchange HDD, follow the procedure as followings (1) Cut off the power to eDVR. (2) Release the Locking system using HDD-RACK KEY (3) Lift up the hand at front 90 degrees and pull Bracket to remove.
When assemble HDD, the base of HDD should be HDD below. (5) After insertion of BRAKET that HDD installed to RACK, take the handle down to fix.
(1) When power is supplied to MD3200M, “Disk Manager” runs automatically after rebooting. If not, run it manually in “MenuUtilityDisk Manager”. (2) There is a HDD that is indicated as “[F] IntA”. Select it. (3) Select “Action” as “Add”, configure a size of alarm partition, and press “Apply” button. Then [F] is changed to [R]. (4) Press the [EXIT] button to shut down “Disk Manager”. (If recording schedule is set, MD3200M will start recording.
When using Disk Farm The following description is when MD3200M has internal primary disk and 3 sets of IEEE1394 HDD. (1) When external HDD farm is connected to IEEE1394 port, “Disk Manager” runs automatically. If not, run it manually in “MenuUtilityDisk Manager”. (2) Select a second HDD of [F] Ext. Press the “Apply” button after selecting action as “Add”. Then [F] is changed to [R]. If connecting the device that is used in MD3200M, type will be indicated as [V]. (3) Select a third HDD of [F] Ext.
When using RAID The following description is when MD3200M has internal primary disk and 1 set of IEEE1394 RAID. Even though several HDDs are connected to RAID, MD3200M will recognize them as only one HDD. For connection and setup of RAID, please refer to the manual of related device. (1) When external HDD RAID is connected to IEEE1394 port, “Disk Manager” runs automatically. If not, run it manually in “MenuUtilityDisk Manager”.
Replacing HDD Checking HDD MD3200M file system (VFS2) sensors bad sector automatically, and the sensored bad sector is not used. The following means when HDD is broken or has some problem in connection. (1) When playback is stopped or MD3200M is rebooted in specific playback range or image searching per event is impossible. (2) When recording is stopped and “Disk Manager” shows HDD type as [X].
(5) Set backup range and press the “Start” button after selecting backup HDD. 1. Backup HDD should be formatted as FAT32 type. 2. Backup data can be replayed with specific S/W in PC such as Control Center Lite-D or MiniPlayer. 3. Backup data is made as “*.re4” file and recognized as CD-R 700MB / DVD-R 4G per each file. 4. Support CD-R backup and should be over CD-R 700MB / DVD-R 4G media. 5. In course of backup, “Auto Delete” function doesn’t run.
Caution in using HDD For handling or guaranteeing HDD, WEBGATE follows HDD guaranty condition. WEBGATE doesn’t bear the responsibility about data loss by user’s mistake in operating. Attention for the system without HDD installed In case of system without HDD, HDD only can only be installed in R-HDD(Removable Hard disk rack). For the internal installation of HDD additionally, For the details, please contact to local distributor. It supports only DVD backup. CD backup will be supported later.
#2. Using CD-ROM Components of CD- ROM disc Installation Guide : eDVR MD3200M Installation Guide User’s Guide : eDVR MD3200M User’s Guide : Control Center Lite-D User’s Guide Control Center Lite-D (Control Center lite-D Remote Management Program) Acrobat Reader : Version 7.0 Preparation To read manual of CD-ROM disc, Adobe Acrobat 7.0 should be installed in client’s PC. If Adobe Acrobat Reader is not installed within client’s PC, use the Acrobat Reader program of CDROM.
#3. How to recognize manufacturing date The manufacturing date by Webgate can be recognized by S/N(Serial Number) attached at the each product. S/N : Serial Number Management number for each Webgate product to combine twelve alphabet character and digit including model name, manufacturing year/month/week You can see serial number by looking at the bottom of product attached label and system info of Configuration Tool. Serial Number Format □ □ □ □ □ □ □ □ □ □ □ □ Year/Month Webgate No.
#4. Specification General CPU 32bit RISC Processor Flash memory 32MB Main memory 256MB OS Embedded LINUX Video channel 32Ch. analog video inputs via BNC connector NTSC or PAL video format are supported (Auto detect) Storage device Int.: 4 HDD bays including 2 hot swap-bay Ext: 2 IEEE 1394b (FireWire) connection ports* 2 eSATA connection ports 1 Network Storage port (RJ45)* Supports Disk management tool for all disks.
Schedule recording Daily : Day / Night / Four-segment time frame Weekly : Weekdays / Weekends, Exception days Conditions : Normal / Event Text Data recording POS/ATM transaction information archived along corresponding video data Manual recording Manual(Emergency) record triggered by font key Audio Recording & Playback Recording level -7~8 (16 step) recording level Monitoring Support remote monitoring and two way audio Network Program Control Center Lite-D (Bundle) Support Control Center seri
Storage temperature -10 ~ 55℃ Operation humidity 30~80%, free of condensation Storage humidity 93% below, free of condensation Data Backup/Expansion/Copy Data backup External HDD(via 1394b or eSATA) Internal CD-R/DVD-R Backup reminder 5~ 95% alarm AVI Copy External USB memory disk(USB 1.
Mechanical Dimension (WⅹDⅹH) 430.0 x 362.0 x 88.0 mm Weight 5.
PelikanCam 555 West Lambert Road, Suite A Brea, CA 92821 Tel : (714) 672-0333 Fax : (714) 672-0360 sales@pelikancam.com www.pelikancam.com The contents of this manual can be modified in accordance with Firmware or Software upgrade.
