Owner manual

ManualsBrandsPella ManualsFurnitureStorm Door Models 35123

Hardware

Kit(s)

Loose Parts

(in Roll-up)

Carton

Roll-up

Carton

Roll-up

Loose Parts

Owner’s Guide and Installation Manual

PELLA

EXPRESS INSTALL

STORM DOOR MODELS

Updated 4/10 35123

NOTE TO THE INSTALLER: This Owner’s Guide and Installation Manual is the property of the

homeowner. Please leave it with the homeowner upon completion of the installation.

Recommended Tools

Power Drill with

3/32” drill bit

Tape Measure

Phillips

Screwdriver #2

For safety reasons, the assistance of a second person is recommended when handling the door.

Read the legend below in order to easily follow along and install your storm door.

For reference, the storm door assembly is illustrated on page 2.

Legend

tresnI

Follow the steps in order, from 1 to 35.

RED objects are the action items for that step.

Steps in BLUE apply to LEFT HINGE congurations ONLY.

(Hinge side will be determined in a later step.)

Steps in GREEN apply to RIGHT HINGE congurations ONLY.

(Hinge side will be determined in a later step.)

MUST READ! Instructions in this box style are IMPORTANT!

To order replacement parts, call

1-800-374-4758

or visit us at

www.pella.com

Please have your registration number

ready when you contact us either by

telephone or on the internet.

TROUBLE SHOOTING GUIDE

is located on page 12 of this manual.

Lay door ﬂat.

Before discarding the carton, make sure ALL parts are

accounted for -- check in carton roll-ups.

The carton material is recyclable

Summary of content (12 pages)

PAGE 1
Updated 4/10 35123 Owner’s Guide and Installation Manual PELLA® EXPRESS INSTALL® STORM DOOR MODELS NOTE TO THE INSTALLER: This Owner’s Guide and Installation Manual is the property of the homeowner. Please leave it with the homeowner upon completion of the installation. 1 2 Recommended Tools Tape Measure Power Drill with 3/32” drill bit Phillips Screwdriver #2 For safety reasons, the assistance of a second person is recommended when handling the door.
PAGE 2
Storm Door Components NOTE: Actual door styles may vary from illustrations, however, the installation steps will be the same. Header Frame Screw Cover Strips Door Hardware Kit Door Closers Includes mounting screws and some handle components Top Mounting Frame Latch Mounting Frame Glass/Screen Retainer Strips Glass Handle Kit Includes handle hardware with seperate instruction sheet Hinge Mounting Frame Screen This is your door’s identification number. Leave this sticker on your door.
PAGE 3
START Remember this is the INTERIOR SIDE of the door Your Installation 1 Snap Turn door over. Re m gla ove s ands scr een ft Li Remove shipping clips. 2 Remove glass and screen. Align outer edges C enter in Opening 3 S ID E V IE W FIRST, center header frame in entryway opening ... 4 ... THEN, align with face of brickmold. 5 Drill 3/32” Pilot Holes 6 Predrill the two holes. Secure with jamb screws. Qty.
PAGE 4
Continued from page 3 7 Position door for LEFT hinge or RIGHT hinge. Inside Facing UP RIGHT HINGE DOORS position metal plate on this side This is the TOP of Your Door Right Hinge Illustration LEFT HINGE DOORS position metal plate on this side Left Hinge Illustration This is the TOP of Your Door Inside Facing 8 Sl id e Sl id e UP Remove any protective film. Slide bottom expander tight onto bottom of door. NOTE: Bottom expander is packaged with the handle for Select® 6000 models.
PAGE 5
Continued from page 4 LEFT HINGE Doors Only RIGHT HINGE Doors Only SLIDE To This Side 11 Set door in opening (resting on bottom spacer from step 10). Right Hinge Illustration Hold tight to hinge side. Predrill the five hinge side hole locations. Secure with screws. Drill 3/32” Pilot Holes Left Hinge Illustration r, e Qty. 5 se i Ra “Mounting Frame Screw Bag” unpainted #6 x 1” Pan Head p, U S lid O ve then Lower 12 SLIDE To This Side Installation Support Block 13 Open the door.
PAGE 6
Continued from page 5 Horizontal Retainer Strip 15 Install glass panel. IMPORTANT: Hold glass in place while installing retainer strips. t Se in e c Pla Install Both Top and Bottom Install horizontal strips first (top then bottom) Vertical Retainer Strip Install Both Left and Right Secure with retaining strips. 16 Predrill the five hole locations. Secure with screws. Drill 3/32” Pilot Holes Qty.
PAGE 7
Continued from page 6 Break-off Tab (Remove if necessary) 18 Position top mounting frame. Note: if you have interference with siding, remove the break-off tab with a pliers, then caulk along the back surface, for protection from rain. Leave this plate in place Right Hinge Illustration 19 Close door. Predrill the two hole locations. Factory Installed Spacer Secure with screws. Drill 3/32” Pilot Holes 20 Qty.2 Left Hinge Illustration Rest on Door Rest mounting frame on door.
PAGE 8
Continued from Hardware Instruction 23 Remove the two hole plugs from the closer bases. Insert into the factory drilled holes near the top corners of the door. 24 Determine which side to install the closers. [Right versus Left]. 25 Align closer base arrow with small notch on mounting frame (install both top and bottom). RIGHT HINGE Install Closers on This Side.
PAGE 9
Continued from page 8 28 Locate the top and bottom closers. To Use: TOP Closer Button One-Touch® Closer To Close: Nudge the door open slightly. BOTTOM Closer Slide top and bottom closers onto their bases. 29 Rotate bottom closer as shown. Right Hinge Illustration Right Hinge Illustration Bottom Closer: Rotate so One-Touch® Button Points Up S l i d e 30 Open the door, then tap then button.
PAGE 10
Continued from page 9 34 Close door. st, dju o A en t en ht os tig Lo n Re the Adjust bottom expander to lightly contact the sill. A d j u s t Sweep Sill (1 Horizontal, 2 Vertical). se rt EdAn gegle d ce In la 35 Angled Edge Points Away From Door Install screw cover strips Snap in P Hint: With the angled edge in place, run your finger down the length of the inner edge to snap in place. Finished with the installation. See page 11 for care and maintenance.
PAGE 11
Care and Maintenance Door Cleaning Use a soft cloth with any household grease-cutting cleaner to clean the door. PLEASE NOTE: Thin marks on the painted surfaces of the door can be removed using turpentine and light rubbing with a clean cloth. IMPORTANT: DO NOT use brass polish or steel wool on the bottom expander - - Use a household grease-cutting cleaner or a mild soap and water solution. Glass Cleaning PLAIN GLASS Models with decorative glass - follow instructions below.
PAGE 12
Trouble Shooting Guide If you have a question that you do not see listed here, or have not been able to resolve through your Pella® Owner’s Manual and Installation Guide, call one of our customer service representatives toll-free at 1-800-374-4758. Common Questions Probable Causes Suggested Solutions Door does not open or close properly. Entryway framing is out or square/plumb or frame is warped 1. Verify the entryway framing and shim as necessary. [See Page 2] Closer(s) out of position or adjustment.