Owner manual

ManualsBrandsPella ManualsFurnitureWood Hinged Patio Door 818K0100

INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION

WOOD HINGED PATIO DOOR – (INCLUDES – STANDARD,

PERFORMANCE UPGRADE AND HURRICANESHEILD® IMPACT

RESISTANT IN-SWING, OUT-SWING)

Important Safety Information:

Pella

HurricaneShield

Products have been tested in accordance with the large missile impact

testing requirements have been certiﬁ ed to meet those requirements. Check with the individual

(building owner, architect, contractor, installer and/or consumer) responsible for the project in

addition to local building code ofﬁ cials to determine if these products comply with local codes.

Pella HurricaneShield Products are neither hurricane proof nor are they shatter proof. Severe wind

and rain may produce temporary conditions which exceed product performance standards. When

these units are subjected to intense storms or extreme conditions, which exceed the intended

design pressures, air, water and ﬂ ying debris inﬁ ltration may occur.

These instructions were developed and tested for use with typical wood frame wall construction

in a wall system designed to manage water. These instructions are not to be used with any

other construction method. Installation instructions for use with other construction methods,

multiple units or bow and bay windows, may be obtained from Pella Corporation or a local Pella

retailer, or by visiting http://www.pella.com. Building designs, construction methods, building

materials, and site conditions unique to your project may require an installation method different

from these instructions and additional care. Determining the appropriate installation method is the

responsibility of you, your architect, or construction professional.

IMPORTANT NOTICE: To achieve maximum door performance, the performance upgrade

installation may be required. Additional performance information may be obtained from your

Pella retailer of www.pella.com. All HurricaneShield doors are required to use the Performance

Upgrade Installation steps contained within this instruction.

Always read the Pella

Limited Warranty before purchasing or installing Pella

products. By installing this product, you are acknowledging that this Limited

Warranty is part of the terms of the sale. Failure to comply with all Pella installation and

maintenance instructions may void your Pella product warranty. See Limited Warranty for

complete details at http://warranty.pella.com.

REMEMBER TO USE APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT.

Instrucciones enspañol en el reverso.

Optional Sill Pan

Water Resistive Barrier

Sheathing

Framing

Flashing Tape

Sill Support

Corner

Flashing

Tapes

Top Flashing Tape

Aluminum Head Flashing

Summary of content (16 pages)

PAGE 1
©2011 Pella Corporation Part Number: 818K0100 INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION WOOD HINGED PATIO DOOR – (INCLUDES – STANDARD, PERFORMANCE UPGRADE AND HURRICANESHEILD® IMPACT RESISTANT IN-SWING, OUT-SWING) Instrucciones enspañol en el reverso. Important Safety Information: Pella® HurricaneShield® Products have been tested in accordance with the large missile impact testing requirements have been certiﬁed to meet those requirements.
PAGE 2
The performance of any building is dependent upon the design, installation, and workmanship of the entire building system. Pella Corporation strongly recommends consulting an experienced architect, contractor, or structural engineer prior to installation of Pella products.
PAGE 3
1 ROUGH OPENING PREPARATION Interior A. Conﬁrm the opening is plumb and level. Note: It is critical that the bottom is level. 1A DOORS • ALL DOORS • ALL DOORS • ALL DOORS • ALL DOORS • ALL DOORS • ALL DOORS B. Conﬁrm the door will ﬁt the opening. Measure all four sides of the opening to make sure it is 3/4" larger than the door in width and 1/2" larger in height. Measure the width at the top, bottom, and center. Measure the height at the far left side, the far right side, and in the center.
PAGE 4
Optional Sill Pan Instructions. I. Cut the sill pan to the width of the rough opening plus 2". DOORS • ALL DOORS • ALL DOORS • ALL DOORS • ALL DOORS • ALL DOORS • ALL DOORS Note: The 2" added onto the rough opening width is for a 1" bend on each end. J. Make a 1" cut in each fold at both ends of the sill pan. Note: These cuts will allow the edges of the sill pan to be bent. Note: 4-5/8" wide for Out-swing and In-swing for 4-9/16" wall condition. For other wall conditions; measure wall depth and add 1/16".
PAGE 5
T. Attach the aluminum sill support or wood blocking to the exterior of the box plate to support the edge of the door sill. Place the sill support ﬂush with the subﬂoor. 1P 1T INTERIO ALL DOORS R SILL PA EXTERI OR SILL 2 N LIP PAN LI P PREPARE THE DOOR FOR INSTALLATION TWO OR MORE PEOPLE WILL BE REQUIRED TO HANDLE THE PANEL AND FRAME SAFELY. A. Remove plastic wrap and cardboard packaging from door. Do not remove plastic shipping spacers.
PAGE 6
PERFORMANCE UPGRADE B. Doors using Installation Clips: Note: If clips are to be bent; prebend before attaching to frame. 3 ALL DOORS • ALL DOORS • ALL DOORS • ALL DOORS #6 x 5/8” corrosion resistant screws Install installation clips. Place each clip so the lip is facing up and against the brickmould at the locations shown in the placement diagram. Lip Secure each clip by driving a #6 x 5/8" corrosion resistant screw through each of the outer two holes of the three holes shown.
PAGE 7
Ó 3D DOORS • ALL DOORS • ALL DOORS • ALL DOORS • ALL DOORS • ALL DOORS • ALL DOORS D. Plumb and square door. Place shims at each hinge &YUFSJP S and lock strike location between the door and the sides of the opening. Keep shims back 1/2" from interior face of the door frame. Insert shims in other locations as needed starting up 6" from the bottom of the door to square it in the opening. Make sure that the reveal around the door(s) is equal.
PAGE 8
of sealant into the three sill strike holes and install the three # 8 x 3" ﬂat head stainless steel screws (provided) into the holes. DOORS • ALL DOORS • ALL DOORS • ALL DOORS • ALL DOORS • ALL DOORS • ALL DOORS K. Shim between the frame and the rough opening at the head strike location and at every frame anchor hole location. Remove and replace head strike screws with three #8 x 3" corrosion resistant screws (provided) through the head strike, door frame, shims and into the rough opening.
PAGE 9
DOORS • ALL DOORS • ALL DOORS • ALL DOORS • ALL DOORS • ALL DOORS • ALL DOORS N. For Doors with adjustable hinges: The hinges can be used to move the panel side to side by moving all hinges in the same direction or the hinges can slightly rotate the panel by adjusting the hinges in opposite directions. Use a T20 Torx wrench to turn the center screw clockwise (+) to increase the space between the hinge side of the frame and door panel.
PAGE 10
5 INSTALL THE PERFORMANCE UPGRADE OR HURRICANESHIELD FASTENERS In-Swing PERFORMANCE UPGRADE & HURRICANESHIELD DOORS • PERFORMANCE UPGRADE Frame Screw Method: Note: If installing with installation clips, proceed to Step E. A. Jambs: Out-swing: On the room side of the jamb; drill and counter-sink 13/64" deep diameter clearance holes through the door frame only and not into the rough opening in the locations shown. (See Out-Swing diagram in lower right).
PAGE 11
D. Secure the jambs and head of the door. Drive #10 x 3-1/2" corrosion resistant wood P E R F O R M A N C E U P G R A D E & H U R R I C A N E S H I E L D D O O R S • P E R FAO AU NR CR EIU PG D IEE L&D P R&M H CA NR EA SH screws through the door frame and shim, into the rough framing. Drive the screws until snug but DO NOT over-tighten the screws. DO NOT bend or bow the unit frame. #10 x 3-1/2" corrosion resistant wood screw 5D 5C Drill 1/8” diameter pilot holes through the clearance hole in the frame.
PAGE 12
DOORS • ALL DOORS • ALL DOORS • ALL DOORS • ALL DOORS • ALL DOORS • ALL DOORS 6 INTERIOR SEAL Caution: Ensure use of low pressure polyurethane window and door insulating foams and strictly follow the foam manufacturer’s recommendations for application. Use of high pressure foams or improper application of the foam may cause the door frame to bow and hinder operation. A. Add a sealant bead across the inner sill and 6" up each jamb between the frame and rough opening.
PAGE 13
DOORS • ALL DOORS • ALL DOORS • ALL DOORS • ALL DOORS • ALL DOORS • ALL DOORS A. Insert backer rod into the space around the door so there is at least a 1/2" clearance between the backer rod and the exterior face of the wall cladding and the brickmould or wood trim. Note: Backer rod adds shape and depth for the sealant line. B. Apply a bead of sealant to the entire perimeter of the door.
PAGE 14
CARE AND MAINTENANCE DOORS • ALL DOORS • ALL DOORS • ALL DOORS • ALL DOORS • ALL DOORS • ALL DOORS Care and maintenance information is available in the Pella Owner’s Manual. You can obtain an owner’s manual by contacting your local Pella retailer. This information is also available at www.pella.com. IMPORTANT NOTICE Because all construction must anticipate some water inﬁltration, it is important that the wall system be designed and constructed to properly manage moisture.
PAGE 15
This page left blank intentionally.
PAGE 16
This page left blank intentionally.