User’s Manual PENTAGRAM Cerberus P 6331-42 The latest versions of manual, drivers and applications are available on www.pentagram.
NOTE! Any information and technical data are subject to change without prior notification and/or indication in this manual. © 2007 PENTAGRAM All rights reserved; copying and reproduction is strictly forbidden.
Cerberus P 6331-42 INDEX INTRODUCTION ...................................................................................................... 5 PACKAGE CONTENTS ....................................................................................... 5 FEATURES.......................................................................................................... 6 PRODUCT OVERVIEW............................................................................................ 7 IMPORTANT NOTES..................
Cerberus P 6331-42 4
Cerberus P 6331-42 Introduction Thank you for purchasing the Cerberus P 6331-42 Modem/Router by PENTAGRAM. Your new router is an all-in-one unit that combines an ADSL modem, ADSL router and Ethernet network switch to provide everything you need to get the machines on your network connected to the Internet over an ADSL broadband connection. The Cerberus P 6331-42 router complies with ADSL2+ standards for deployment worldwide and supports downstream rates of up to 24 Mbps and upstream rates of up to 1 Mbps.
Cerberus P 6331-42 Features • A 4-port 10/100Mbps fast Ethernet switch is built-in with automatic switching between MDI and MDI-X for 10Base-T and 100Base-TX ports, with auto detection allowing you to use either straight or cross-over Ethernet cables. • Network Address Translation (NAT) allows multiple users to access outside resources such as the Internet simultaneously with one IP address/one Internet access account.
Cerberus P 6331-42 • High Speed Internet Access: downstream rates of up to 24Mbps and upstream rates of up to 1Mbps. Cerberus ADSL2+ Lite is compliant with the following standards: ANSI T1.413 issue 2, ITU-T G.992.1 (G.dmt), ITU-T G.992.2 (G.lite), G.994.1 (G.hs, Multimode), ITU-T G.992.3 (ADSL2 G.dmt.bis), ITU-T G.992.5 (ADSL2+; Annex A, I, J, L & M).
Cerberus P 6331-42 Back Panel Label RP-SMA Connector LINE (RJ-11) LAN 1-4 (RJ-45) RESET PWR ON/OFF Used for... Connecting the external antenna Connecting the telephone cable Connecting with computers/devices through Ethernet cable Resetting the device. Connecting with supplied power adapter (12V 1A) Switching the device on/off Default Settings Before changing configuration familiarize yourself with these default settings. LAN/WLAN Ports IP Address 192.168.1.100 Subnet Mask 255.255.255.
Cerberus P 6331-42 Resetting router • • • Turn router on and wait for ADSL LED to lit or start blinking. Press and hold RESET button on the back panel of router for 5-10 seconds and then release it. After reset LEDs will return to their normal behavior and all settings will be reset to their default value. You can login to router configuration page using default username and password: admin / pentagram. Connecting Cerberus to Computer.
Cerberus P 6331-42 Windows Vista Note: Network configuration requires administrator privileges. When User Account Control window pops up, either click Continue (Administrator user) or select Administrator user and enter valid password (Standard user). 1. Click Start → Control Panel. 2. Click View network status and tasks. 3. Click View status for appropriate connection. 4. In General tab, Click the Properties button. 5.
Cerberus P 6331-42 Windows 2000/XP 1. Click Start → Settings → Control Panel. Double-click the Network Connections icon (2000/XP Classic view) or click Network and Internet Connections icon and then Network Connections icon (XP Default view). 2. Double-click the Local Area Connection icon. 3. In General tab, Click the Properties button. 4. In General tab, select Internet Protocol (TCP/IP) and click Properties. 5.
Cerberus P 6331-42 Windows 95/98/Me 1. Click Start → Settings → Control Panel. Doubleclick the Network icon. 2. In Configuration tab, select TCP/IP for appropriate network adapter and click Properties. 3. In IP Address tab, select Obtain an IP address automatically. 4. In DNS Configuration tab, select Disable DNS 5. Click OK to save settings and close TCP/IP Properties window. To make sure that network adapter properly obtained an IP address from router’s DHCP server: 1. click Start > Run 2.
Cerberus P 6331-42 Configure router via web browser Cerberus P 6331-42 router can be configured via web browser, which is usually integrated with operating system. Router offers clear and simple interface. Login 1. 2. Launch the Web browser Type the default router’s IP address: http://192.168.1.100 in the address bar 3.
Cerberus P 6331-42 Navigation Steps to navigate the Web configuration from the Site Map are summarized below: • Quick Start – wizard that helps to configure your router, • Interface Setup – configure Internet and LAN functions, • Advanced Setup – configure advanced features, • Access Management – manage Internet access options, • Maintenance – set a new password, set the time zone, upgrade or reload firmware and run diagnostic tests on the router, • Status – router device information, system logs and perf
Cerberus P 6331-42 Quick Start Wizard Click Quick Start to guide you to configure the device to connect your ISP and have Internet access within minutes. This Quick Start will guide you step by step to configure the password, time zone, and WAN settings of you device. This Wizard is a helpful guide for first time uses to the device. It is strongly recommended to use Quick Start to configure your ADSL settings. Click on the RUN WIZARD button to start the Quick Start wizard.
Cerberus P 6331-42 Setting a New Password This screen helps you set a new password, replacing the default password. Enter new password in New Password and Confirmed Password fields. Click on BACK to return to the previous screen, on NEXT to continue, or on EXIT to exit the wizard without saving. Choose your Time Zone Select the appropriate time zone for your location from the dropdown list. Click on BACK to return to the previous screen, on NEXT to continue, or on EXIT to exit the wizard without saving.
Cerberus P 6331-42 Set your Internet Connection Glossary: • • • • Multiplexing - Two conventions identify what protocols a virtual circuit (VC) is carrying. Be sure to use the multiplexing method your ISP requires: VC-Based Multiplexing – In VC-based multiplexing, by prior mutual agreement, each protocol is assigned to a specific virtual circuit. For example, VC1 carries IP, etc.
Cerberus P 6331-42 • Dynamic IP Address A dynamic IP address connection requests a new IP address from your ISP each time you connect to it. Enter VPI (Virtual Path Identifier), VCI (Virtual Channel Identifier) and select your Connection Type from the dropdown list. Your ISP should provide the above information. Click on BACK to return to the previous screen, on NEXT to continue, or on EXIT to exit the wizard without saving.
Cerberus P 6331-42 • PPPoE/PPPoA Configure connection based on PPPoE / PPPoA protocol. Enter Username, Password, VPI (Virtual Path Identifier), VCI (Virtual Channel Identifier) and select your Connection Type from the dropdown list. Note that you must enter the user name exactly as your ISP assigned it. If the assigned name is in the form of user@domain where domain identifies a service name, enter it exactly as given.
Cerberus P 6331-42 Finishing the Wizard The Quick Start wizard now has all the information it needs. You MUST click NEXT, to save configuration! Click on BACK to make changes or correct mistakes. Click on NEXT to save the current settings. Click on EXIT to exit the wizard without saving. Your changes have been saved. Click on CLOSE. The Quick Start wizard window will close.
Cerberus P 6331-42 Internet The Internet screen allows you to set up how your router connects to the Internet. If you already ran the Quick Start wizard, the information you provided to the wizard should be entered into the fields already. After you finish the changes, click on the SAVE button to save your changes.
Cerberus P 6331-42 • ATM VC ATM settings are used to connect to your ISP. Your ISP provides VPI, VCI, settings to you. In this Device, you can totally setup 8 PVCs on different encapsulations if you apply 8 different virtual circuits from your ISP. You need to activate the VC to take effect. For PVCs management, you can use ATM QOS to setup each PVC traffic line’s priority. Virtual Circuit – Select the VC number you want to setup. Status – Select whether selected connection is Activated or Deactivated.
Cerberus P 6331-42 • Encapsulation Select the encapsulation protocol your ISP uses. The following section will vary depending on which encapsulation protocol you select. • Dynamic IP Address Select this option if your ISP provides you an IP address automatically. Please enter the Dynamic IP information accordingly. Encapsulation – Select your encapsulation type from the dropdown list. NAT – Select whether NAT (Network Address Translation) is Enabled or Disabled.
Cerberus P 6331-42 • PPPoA/PPPoE Select this option if your ISP requires you to use a PPPoA/PPPoE connection. Username – Enter your username for your PPPoE/PPPoA connection. Password – Enter your password for your PPPoE/PPPoA connection. Encapsulation – Select your encapsulation type from the dropdown list. Half Bridge – external IP address obtained from ISP will be transferred to first computer which will connect to and obtain IP address from router. Only this computer will have access to internet.
Cerberus P 6331-42 LAN There are the IP settings of the LAN Interface for the device. These settings may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is provided to your internal network and cannot be seen on the Internet. • Router Local IP IP Address – Enter the IP address of your ADSL router in dotted decimal notation, for example, 192.168.1.100 (default setting).
Cerberus P 6331-42 • DHCP The DHCP Server gives out IP addresses when a device is booting up and request an IP to be logged on to the network. It must be set as a DHCP client to obtain the IP address automatically. By default, the DHCP Server is enabled. The DHCP address pool contains the range of the IP address that will automatically be assigned to the client on the network. Disabled – DHCP server is Disabled Enabled – DHCP server is Enabled Relay – router acts as a relay to different computer/device.
Cerberus P 6331-42 Wireless • Access Point Settings Access Point – Activate or deactivate Access Point function of router. Channel ID – Select country and channel (frequency) used by this network. Current channel is displayed in Current Channel field. Beacon Interval – The Beacon Interval value indicates the frequency interval of the beacon. Enter a value between 20 and 1000. A beacon is a packet broadcast by the Router to synchronize the wireless network.
Cerberus P 6331-42 Service Data Unit) size TURNS OFF the RTS/CTS handshake. Set this attribute to ZERO TURNS ON the RTS/CTS handshake. Enter a value between 0 and 2432. Fragmentation Threshold – The threshold (number of bytes) for the fragmentation boundary for directed messages. It is the maximum data fragment size that can be sent. Enter a value between 256 and 2432. DTIM – This value is between 1 and 255, indicates the interval of the Delivery Traffic Indication Message (DTIM). 802.
Cerberus P 6331-42 Pre-Shared Key – Key used to encrypt data. Both the ADSL Router and the wireless clients must use the same WPA-PSK Key for data transmission. • Wireless MAC Address Filter You can allow or deny a lust of MAC addresses associated with the wireless stations access to the ADSL Router. Active – Use this option to enable or disable MAC address filtering. Action – Select Deny Association to block access to the router, MAC addresses not listed will be allowed to access the router.
Cerberus P 6331-42 Advanced Setup Tab Firewall Firewall – Select this option can automatically detect and block Denial of Service (DoS) attacks, such as Ping of Death, SYN Flood, Port Scan and Land Attack. SPI – Select this option to Enable or Disable the SPI feature. (NOTE: If you enable SPI, all traffics initiate from WAN would be blocked, including DMZ, Virtual Server, and ACL WAN side).
Cerberus P 6331-42 Routing This table lists IP address of Internet destinations commonly accessed by your network. When a computer requests to send data to a listed destination, the device uses the Gateway IP to identify the first Internet router it should contact to route the data most efficiently. Select this option will list the routing table information. You can press ADD ROUTE to edit the static route. (As below screen) ADD ROUTE – click this button to set Static Routing information.
Cerberus P 6331-42 propagated to other hosts through RIP broadcasts. If you choose No, this route is kept private and is not included in the RIP broadcasts. When you are done making changes, click on SAVE to save your changes, DELETE to delete the rule with the parameters you set, BACK to return to the previous screen or CANCEL to discard changes.
Cerberus P 6331-42 Many-to-Many No Overload – In Many-to-Many No Overload mode, the TC3162 EVM maps each local IP address to a unique global IP address. Server – This type allows you to specify inside servers of different services behind the NAT to be accessible to the outside world. The following table summarizes these types. TYPE One-to-One Many-to-One (SUA/PAT) IP MAPPING ILA1 IGA1 ILA1 IGA1 ILA2 IGA1 ... ILA1 IGA1 ILA2 IGA2 ILA3 IGA1 ILA4 IGA2 ... ILA1 IGA1 ILA2 IGA2 ILA3 IGA3 ILA4 IGA4 ...
Cerberus P 6331-42 with single IP, since they have only one IP, there is no need to individually define the Address Mapping rule. DMZ / Virtual Server / IP Address Mapping – opens corresponding page: • DMZ A DMZ (de-militarized zone) is a host between a private local network and the outside public network. It prevents outside users from getting direct access to s server that has company data. Users of the public network outside the company can access only the DMZ host.
Cerberus P 6331-42 • Virtual Server The Virtual Server is the server or server(s) behind NAT (on the LAN), for example, Web server or FTP server, that you can make visible to the outside world even though NAT makes your whole inside network appear as a single machine to the outside world. Virtual Server for - selected in Number of IPs field in main NAT window. Rule Index – The Virtual server rule index for this VC. You can specify up to 10 rules.
Cerberus P 6331-42 • IP Address Mapping The IP Address Mapping is for those VCs that with multiple IPs. The IP Address Mapping rule is per-VC based. (only for Multiple IPs’ VCs). Address Mapping Rule – PVC to set. Rule Index – The Virtual server rule index for this VC. You can specify up to 16 rules. All the VCs with single IP will use the same Virtual Server rules. Rule Type – There are 4 types of One-to-One, Many-to-One, Many-to-Many Overload and Many-to-Many No-Overload.
Cerberus P 6331-42 ADSL Select this option to set ADSL Mode and ADSL Type information. ADSL Mode – Select which mode your ADSL connection uses from the dropdown list. The option has Auto Sync-up, ADSL2+, ADSL2, G.DMT, T1.413, G.LITE. ADSL Type – Select the ADSL type you use from the dropdown list: ANNEX A, ANNEX I, ANNEX A/L, ANNEX M, ANNEX A/I/J/L/M. When you are done making changes, click on SAVE to save your changes.
Cerberus P 6331-42 Access Management Tab ACL Go to Access Management → ACL to enable remote management. Access Control Listing (ACL) is a management tool that acts as a filter for incoming or outgoing packets, based on application. You may use telnet or Web to remotely manage the ADSL Router. User just needs to enable Telnet or Web and give it an IP address that wants to access the ADSL Router. The default IP 0.0.0.0 allows any client to use this service to remotely manage the ADSL Router.
Cerberus P 6331-42 Filter The Router provides extensive firewall protection by restricting connection parameters to limit the risk of intrusion and defending against a wide array of common hacker attackers. Appearance of this tab is dependent on option selected from Filter Type Selection list.
Cerberus P 6331-42 • IP / MAC Filter IP / MAC Filter enables you to filter data based on source MAC Address or source/destination IP Address or Port number. IP / MAC Filter Set Index – The IP / MAC Filter Set Index from 1 to 12 and each index can set up to 6 IP / MAC Filter. Interface – Choices from PVC0 to PVC7 and LAN.
Cerberus P 6331-42 Direction – Choices are Both, Incoming and Outgoing. Select which direction of data flow you wish to apply the filters to. Note that Incoming and Outgoing are from the point of view of your router, relative to the interface you select. For WAN, data coming from outside your system is considered Incoming and data leaving your system is Outgoing. For LAN, data leaving your system is considered Incoming and data entering your system is Outgoing.
Cerberus P 6331-42 • Application Filter Application Filter enables you to block popular Instant Messaging applications and Real Audio/Video. Application Filter – Select this option to Activate / Deactivate the Application filter. ICQ – Select this option to Allow / Deny ICQ. MSN – Select this option to Allow / Deny MSN. YMSG – Select this option to Allow / Deny Yahoo messenger. Real Audio/Video – Select this option to Allow / Deny Real Audio/Video.
Cerberus P 6331-42 SNMP The Simple Network Management Protocol (SNMP) is used for exchanging information between network devices. It enables a host computer to access configuration, performance, and other system data that resides in a database on the modem. The host computer is called a management station and the modem is called an SNMP agent. The data that can be accessed via SNMP is stored in a Management Information Database (MIB) on the modem.
Cerberus P 6331-42 UPnP UPnP (Universal Plug and Play) is a distributed, open networking standard that uses TCP/IP for simple peer-to-peer network connectivity between devices. An UPnP device can dynamically join a network, obtain an IP address, convey its capabilities and learn about other devices on the network. In turn, a device can leave a network smoothly an automatically when it is no longer in use. UPnP broadcasts are only allowed on the LAN.
Cerberus P 6331-42 DDNS The Dynamic Domain Name System allows you to update your current dynamic IP address with one or many dynamic DNS services so that anyone can contact you (in NetMeeting, CUSeeMe, etc.). You can also access your FTP server or Web site on your own computer using a DNS-like address (for instance myhost.dhs.org, where my host is a name of your choice) that will never change instead of using an IP address that changes each time you reconnect.
Cerberus P 6331-42 Maintenance Tab Administration There is only one account that can access Web-Management interface-Administration. Admin has read/write access privilege. In this web page, you can set new password for admin. New Password – Type the new password in this field. Confirm Password – Type the new password again in this field. Click SAVE to save your changes. Note: If you ever forget the password to log in, you may press the RESET button up to 6 second to restore the factory default settings.
Cerberus P 6331-42 • NTP Server automatically Current Date/Time – This field displays an updated Date and Time when you reenter this menu. Time Zone – Choose the Time Zone of your location. This will set the time difference between your time zone and Greenwich Mean Time (GMT). Daylight Saving – Choose “Enabled” or “Disabled” to use daylight savings time. NTP Server Address – Type the IP address or domain name of your timeserver.
Cerberus P 6331-42 Firmware You can upgrade the firmware of the router and save/load configuration Romfile in this page. During firmware upgrade process all router setting are reset to default values. Thanks to Romfile it is possible to save router’s configuration to file and to load this file after upgrade process. Make sure the firmware you want to use is on the local hard drive of the computer. It might take several minutes, don’t power off it during upgrading.
Cerberus P 6331-42 SysRestart The SysRestart screen allows you to restart your router with either its current settings still in place or the factory default settings. System Restart with – If you wish to restart the router using the factory default settings (for example, after a firmware upgrade or if you have saved an incorrect configuration), select Factory Default Settings to reset to factory default settings. Otherwise, you can select Current Settings.
Cerberus P 6331-42 Status Tab Device Info The Device Info screen is a tool that you use to monitor your ADSL Router. It shows the Firmware Version, WAN, LAN, and MAC address information. Note that these fields are readonly and are not meant for diagnostic purposes. Except the Virtual Circuit, click the drop-down list and select the name of the Virtual Circuit on which the system status is to be shown. • Device Information Firmware Version – This filed displays current firmware version.
Cerberus P 6331-42 • LAN IP Address – The LAN port IP address. Subnet Mask – The LAN port IP subnet mask. DHCP Server – The status of DHCP Server (Enabled or Disabled). • WAN Virtual Circuit – Click the drop-down list and select the name of the Virtual Circuit on which the system status is to be shown. Status – Connected or Not Connected. Connection Type – The WAN Connection Type. IP Address / Subnet Mask / Default Gateway / DNS Server – Connection parameters.
Cerberus P 6331-42 • between the signal power level received at the Client ADSL Router and the reference signal power level transmitted from the Central Office DSLAM. Data Rate – This field displays the ADSL data rate. System Log The System Log displays data generated or acquired by routine system communication with other devices, such as the results of negotiations with the ISP's computers for DNS and gateway IP addresses. The device keeps a running log of events and activities occurring on the Router.
Cerberus P 6331-42 Statistics The ADSL Router keeps statistic of traffic that passes through it. You are able to view the amount of packets that passes through the Router on both the WAN port & the LAN port. The traffic counter will reset if the device is rebooted. You can select Ethernet/ADSL to view the statistics report of LAN/WAN. • Ethernet The Ethernet screen gives you information on how much data your router has transmitted and received across the Ethernet connection.
Cerberus P 6331-42 • Wireless The Wireless screen gives you information about how much data your router has transmitted or received across the WLAN connection. Click on REFRESH to update the screen. Help Tab Router’s online help.
Cerberus P 6331-42 Troubleshooting If the router is not function properly, first check this session for simple troubleshooting before contacting your Internet service provider (ISP) for support. Using LEDs to Diagnose Problems The LEDs are useful aides for finding possible problem causes. Power LED The PWR LED on the front panel does not light up.: 1. Make sure that the power adaptor is connected to the router and plugged in to an appropriate power source. Use only the supplied power adaptor; 2.
Cerberus P 6331-42 Problems with the Web Interface I cannot access the web Interface: 1. Make sure you are using the correct IP address of the router. Check the IP address of the router; 2. Make sure that there is not a console session running; 3. Check that you have enabled web service access. If you have configured a secured client IP address, your computer’s IP address must match it. Refer to the chapter on remote management for details; 4.
Cerberus P 6331-42 3. Restart the router. If you still have problems, you may need to verify your VPI, VCI, type of encapsulation and type of multiplexing settings with the telephone company and ISP. I cannot get a WAN IP address from the ISP: 1. Ensure that all other devices connected to the same telephone line as your router (e.g.
Cerberus P 6331-42 58
Cerberus P 6331-42 59
Cerberus P 6331-42 60
