User Manual

13
INTELLIFLO
®
Variable Speed Pump Installation and User’s Guide
12
INTELLIFLO
®
Variable Speed Pump Installation and User’s Guide
Pump Menu: Speeds 1-8
SPEED 1-8
Speed 1 (1-4)
Manual
Schedule
Egg Timer
Set Speed - Default: MANUAL
Set Speed
Set Start Time
Set Stop Time
Set Speed
Time
Speed 5 (5-8)
Schedule
Set Speed
Set Start Time
Set Stop Time
Disabled
Default: Disabled
MENU
Set Speeds 1-8 in Schedule Mode
In Schedule mode, Speeds 1-8 can be programmed
to run a certain speed at a certain time of day. To run
a scheduled speed, press Start/Stop. The screen will
display “Running Schedules” when it is ready to run
a scheduled speed. If Start/Stop is pressed while a
scheduled speed is running, “Running Speed _” will be
displayed (see far right image).
1. Press Menu.
2. Use Up or Down arrows to scroll to “Speed 1-8”,
then press Select.
3. Use Up or Down arrows and press Select for the
speed you wish to set and schedule.
4. Press Select (display will be highlighted) and
scroll to “Schedule”.
5. Press Enter.
6. Press Down arrow (“Set Speed” will display) and
press Select to change. Use the Up or Down
arrow to adjust speed.
7. Press Enter to save the new speed.
8. Press the Down arrow again, “Set Start Time” will
display. Press Select - the cursor will highlight the
minute column.
9. Use the Up or Down arrow to change the time
and the Left or Right arrow to move cursor from
minutes to hours.
10. Press Enter to save the new start time setting.
11. Press Down arrow - “Set Stop Time” will display. Press
Select. Repeat Steps 8-9 to set stop time.
12. Press Enter to save the new stop time setting.
13. Press Start/Stop.
The IntelliFlo
®
Variable Speed Pump will prime and be-
gin to run the programmed schedule at the specified
start time.
When running in Schedule or Egg Timer mode,the
countdown time (T 00:01) showing the hours and
minutes remaining is displayed.
12:15p
Set Speed
Schedule
Note: The pump will not run the scheduled speeds until the
Start/Stop button is pressed (LED on) to place the pump in
Schedule mode.
Note: When two speeds are scheduled during the
same run time the pump will run the higher RPM Speed
regardless of Speed # in use.
Note: The most recent command, Manual or Schedule,
takes priority regardless of speed number RPM.
Programming Schedule for Constant Run
A speed cannot be programmed with the same start
and stop times. To run a speed without stopping, set
the Start time one minute after the stop time.
Example: A single speed will run non stop if programmed
with a Start Time of 8:00 AM and a Stop time of 7:59 AM.
12:15p
750 RPM
T 1:05 150 WATTS
Running Speed 1
EXT CONTROL
Program 1
Speed - Default: 750 RPM
Speed - Default: 1500 RPM
Program 2
Program 3
Speed - Default: 2350 RPM
Speed - Default: 3110 RPM
Program 4
MENU
Pump Menu: External Control
External Control
This function is for programming speeds that will run
when the IntelliComm
®
Communication Center sends
it a command. For example, Terminal 3 and 4 in the
IntelliComm system will correspond to External Control
Program #1. (5 and 6 to Ext Ctrl #2).
Use the External Control feature to program the
IntelliComm system power center.
To access the External Control menu:
1. Check that the green power LED is on.
2. Press the Menu button.
3. Use Up or Down arrow to scroll to “Ext. Ctrl.”.
4. Press Select. “Program 1” is displayed.
5. Press Select. “750 RPM’ is displayed.
6. Press Select The “RPM” number will highlight.
7. Press Up or Down arrow to change the RPM
setting.
8. Press Enter to save the setting.
Note: To cancel any changes, press the Escape
button to exit without saving.
9. Press Escape to return to set Program 2.
10. Use Up or Down arrow to scroll to “Program 2”.
11. Repeat Steps 5 through 9 to set Program 2, 3,
and 4.