User manual

!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
The camera has infrared illuminat
You can improve the quality of the
image at night by using additional illumination. The camera
automatically switches to black and white in low light conditions and in
artificial light.
If you want to install the camera outdoors, then protect the camera
against direct rainfall if possible. The mains adapter must be in a dry
location. The connection between camera and mains adapter cable must
be protected against moisture.
Ensure that there is apossible cable routing at the installationlocation.
The maximum range of the wireless signal is approx. 100 m (and up to
150 m in optimal conditions) with line of sight contact between camera
and monitor. Within buildings the range is greatly reduced by walls and
floors, in particular those made of steel reinforced concrete, to a
maximum of 20 m. Metal housings, shelves and mirrors also block the
wireless signal.
The wireless transmission can also be affected by strong electric fields
and other wireless equipment. Ensure an adequate distance of the
camera and receiver to microwave ovens, cordless phones, mobile
phones, wireless devices in the 2.4GHz frequency band, electric motors
and high voltage devices orpower cables.
The monitor must be placed on a solid and level surface, ideally 1m
above the floor (optimal reception).
The camera can be wallor ceiling mounted (see fig. E:I and II).
For wall or ceiling installation mount the bracket [25] at a suitable
location using the screws [35] and if necessary the wall plugs [34]
provided.
Screw the bracket into the appropiate threaded hole in the camera
housing.
Adjust the angle of the camera to givethe required view and then tighten
thetriangularnut[23]andthewingscrew[24].
Screw the antenna [33] into the antenna connection [27] so that the
antennaisinanuprightposition.
Connectthe DC-plug ofthe mains adapter cable[30] to themainsadapter
connection[29]ofthecameracable.
Connectthemainsadapterwithasuitablemainsoutlet.
ThePOWERLED[20]lightsred.
Foldoutthestand[8]tostandonalevelsurface.
Connect the DC-plug of the mains adapter cable [9] to the mains adapter
connectionofthemonitor[18].
Connectthemainsadapterwithasuitablemainsoutlet.
Afterconnectionofthepowersupplythesystemisinoperation.
Removetheprotectionfoilfromthescreen[3].
8. Installation and connection of the camera
9. Connectionofthemonitor
10. Operation
ion [21] for the close range. This is
activated by the daylight sensor [32].
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
To record video insert a readable and unlocked SD-card in the slot [6], if
the card is not formatted then format it before the first use, as described in
chapter12.9.
Press the on/off button [7] on the monitor, the power-LED [11] lights
greenandthecamerapicturewillbedisplayedonthescreen.
TheLithium battery starts chargingautomatically when the mainsadapter
isconnected.Let thebatterycharge fullybeforeportable useofthe monitor
(withoutthemainsadapter).PayattentiontotheBatteryLED:
BatteryLED[10]lightsred: battery charge low; connect the mains
adapterwithasuitablemainsoutlet
BatteryLED[10]lightsgreen: battery charging, leave mains adapter
connecteduntilLEDgoesoff
BatteryLED[10]off: batteryischarged
Thedirection ofthe antenna[2]canbe selectedforthebest reception.The
recommendedpositionisvertical.
To turn off the monitor hold the on/off button [7] pressed until "POWER
OFF"isdisplayed
Thesignalsfromamaximumof4camerascanbereceived.Thecamerawiththe
setisprogrammedinthefactorytochannel1.(seeChanelindicator[37])
The connection of thecamera withthe monitoris shownby the connection LED
[22] on the camera whilst the reception indicator [36] on the screen displays
thereceptionqualitywithupto4bars.
Pressthedirectionbuttons[12: / ]toscrollthroughchannels1to4.
Selectthemonitorvolumeusingthedirectionbuttons[12: / ].
Press the recordbutton[5] to start videoand audio recording (recording is
splitinfilesofmax.30seconds).
Presstherecordbuttonagaintostoptherecording.
IftheScanPeriodisactivated,the imageofthe camerathatcan beseenon
themonitorisrecorded.InQuadfunction,norecordingispossible.
OpentheOSDmenubypressingthemenubuttononceortwice[13].
Movetotherequirediconusingthedirectionbuttons[12].
PresstheOK[16]buttontoselecttheicon.
ChoosethedesiredsettingusingthedirectionbuttonsandtheOKbutton.
Usethemenubuttontogobackinthemenu.
PressthemenubuttononcemoretoleavetheOSDmenu.
The OSD menu will close automatically after 20 seconds if no buttons are
pressed.
11.Basicfunction
12. SettingsinOSDmenu
11.1 Wireless connection
11.2 Channel Selection
11.3 Monitor volume
11.4 Recording
GB - 23