User manual

GB-68
!
!
!
!
!
!
!
!
!
!
Pressthe key.
Use and keytoselect“AutoAnswer”.
Pressthe key.
Use and keytoselect“HSSettings”.
Pressthe key.
Use and keytoselect“Date&Time”.
Pressthe key.
Pressthe”Select” key.Thedisplayshowsthecurrentsetting.
Use or keytoselect“DD-MM”(DayDay-MonthMonth)or
“MM-DD”(DayDay-MonthMonth).
Pressthe“Save” key.
Use or keytoselect“12-Hour”or“24-Hour”.
Pressthe“Save” key.
Enterthedatewiththenumerickeys0to9.
Pressthe“Save” key.
Enterthetimewiththenumerickeys0to9.
Pressthe“Save” key.
Use and keytoselect“HSSettings”.
Pressthe key.
Use and keytoselect“SelectBase”.
Pressthe key.
Thedisplayshowsthecurrentsetting.
Use or keytoselectONorOFFtoenableordisablethefunction.
Pressthe“Save” key.Youwillhearaconfirmationbeep.
Factorydefault:On
Use or key to choose between “Date Format”, “Time
Format”,“SetDate”or“SetTime”.
Factorydefault:DateFormat:DD-MM,TimeFormat:24-Hour
!
!
!
!
!
!
!
!
!
!
!
!
21.8 Settingdateandtime(Date&Time)
21.9 Selectingabase(SelectBase)
DateFormat
TimeFormat
SetDate
SetTime
“Select” "Alarm"appears.
“Select”
Pressthe“Menu” key.
“Select” "Alarm"appears.
“Select”
Pressthe“Menu” key.
“Select” "Alarm"appears.
“Select”
!
!
!
!
This function allows you to select a base from thosealready registered tothe
handset(upto4basescanberegisteredtoonehandset).
Thedisplaytheshowsthecurrentbase.
Use or keytoselectthedesiredbase.
Press the “Select” key. If you select a non-existent base, the
handset will sound a warning tone. After a short time, a confirmation
melody will sound, and the name of the handset will change
respectively.
Note:
Notes:
Thehandsetwillonlyworkwiththebaseithaslastbeenregisteredto,orwith
theselectedbase.
If the registration of a handset was deleted, it can be registered to the
baseagainasdescribedabove.
To register a registered handset to another base, simplyfollow the steps
describedabovewithanotherbase.
Thehandsetwill onlyworkwiththebaseithaslastbeenregisteredto,or
withtheselectedbase(seechapter22.9).
21.10 Resettingthehandset(HSReset)
!
!
!
!
!
!
!
Use and keytoselect“HSSettings”.
Pressthe key.
Use and keytoselect“HSReset”.
Pressthe key.
Use and keytoselect“Registration”.
!
!
!
!
!
!
22. Registering a handset to a base
(Registration)
Pressthe“Menu” key.
“Select” "Alarm"appears.
“Select”
Pressthe“Menu” key.
Pressthe“Select”key .
Use or keytoscrollthroughthebasenameslist(”Base1”to
“Base4”.
Pressthe“Select”key tochooseabase.
As soon as the base is found, and the handset is successfully registered,
youwillbepromptedtoenterthePINcode(thedefaultoneis0000).
!
!
!
!
Thedisplayshows"PIN ?".
EnterthecurrentPINcode.
Press the “Reset” key. If the PIN code is validated, all Base
settings will be returned to the factory default. Otherwise a warning
sound will be heard and the settings will remain. After resetting, the
handsetwillreturntostandbymode.
The supplied handset is already registered with the number 1. You can
register up to 5 handsets/door units to the same base (see chapter 27
"Optionalaccessories").Ahandsetcanberegisteredtoupto4bases.
Press and hold the key [59] on the bottom of the base for at least 5
seconds.
Press the key. On validation of the PIN code, the registration tone
willsoundandthebaseassignsanumbertothehandset.IfthePINcode
enteredisinvalid,awarningtonewillsound,andthehandsetwillreturn
to the previous registration state. If the base is not found, the handset
willbehaveaccordingtotheOutofRangecondition.
!