User manual

GB-59
Attention!
TIP!
Doorunit:
Base:
Donotexposetheproducttofireorhightemperature!
Protect the product against strong magnetic or electrical fields and
againststrongmechanicalloadsandvibrations!
Use the product only with the original components or original
accessories!
Before installing and operating the product check the package for
damagesandcompleteness.
If the unit is to be unused for a longer period, disconnect the mains
adapterfromthemainssupplyandremovethebatteries.
Do not connect any damaged device (e.g. transport damage) and
disconnectthepowersupplyimmediatelyinthecaseofdamage.Unplug
the mains adapter fromthe mainssocket. Arrangefor the damage tobe
repairedimmediatelybyaspecialist!
This product produces and uses radio frequency. If the product is not
installed and used according to the manual it may disturb or be
disturbedbyotherdevices.Incaseofdisturbancesrelocatetheproduct.
Beforeinstalling the product plan thelocation.Checkthewirelessconnection
andthefunctionofthemicrophoneinthedoorunit.
Observethefollowingpoints:
Mount the door unit at such a height that conversation is possible. Pay
attentiontothepositionofthe microphoneandspeaker,theseshould be
at the average head level of visitors. The bell button must also be
accessible.
Ifthedoorunitismountedoutdoors the location must be protected from
directrainfall.
If an external supply or a door release is to be connected ensure a
suitable cable routing, as the mains adapter and relay module must be
locatedindoors.Useacablewithcorediameter0.2- 0.7mm.
Themaximumradiofrequencyrangeisup to 200 m with free space between
thedoorunit andthebase,andbetweenthebaseandthehandset.Therange
indoors is considerably reduced (max. range typically 30 m) through walls
and floors (especially of steel reinforced concrete). Metal surfaces, e.g.
refrigerators,shelving,andcoatedmirrors,alsoimpederadiotransmission.
The radio transmission can be affected by strong electrical-magnetic fields
and other wireless appliances. Ensure adequate distance from microwave
ovens, mobile phones, other wireless appliances, electric motors and mains
powercables.
Place the base on a suitable level and solid surface, ideally 1m above the
!
!
!
!
!
!
!
!
!
!
7.Locationoftheproduct
floor(forbetterreception).
Placethe base at acentral place inside theresidence, e.g. inthe hall. Ensure
thatthechimecanbeheardeverywhereinsidetheresidence.
Ensure that there is a mains power socket within the range of the mains
adaptercable.
Removethebellbutton[3]carefullyfromthedoorunit[1].
With the use of a small knife, remove the name card carefully from the
bellbutton.
Labelthenamecard.
Reinsertthenamecardintothebellbutton.
Reinsertthebellbuttonintothedoorunit.
Hold the bracket [15] to the desired location and mark the two drilling
holesthroughthemountingholes[16].
Drillthetwoholes.
Fix the bracket with the supplied screws [21] and wall plugs [20], if
required.
Openthebatterycompartment[13] of the door unit by sliding downthe
batterycompartmentcover[11].
Insert two LR14 (C), 1,5 V alkaline batteries into the battery
compartment. Pay attention to the correct polarity. The door unit will
sound.
Closethebatterycompartmentwiththebatterycompartmentcover.
Slidethedoorunitontothebracket.
Screwthetorxscrew[23]firmlythroughthehole[19]intothehole[12],
usingthesuppliedtorxwrench[24].
Hold the bracket [15] to the desired location and mark the two drilling
holes through the mounting holes [16]. Make sure that there is a lead-
throughfortheconnectioncableexactlybehindthecablehole[18].
Drillthetwoholes.
Fix the bracket with the supplied screws [21] and wall plugs [20], if
required.
Removetherubbercover[5]fromthedoorunit.
TIP!
!
Place the base where there is wireless contact to the door unit. If you
wishtoplacethehandsetfurtherfromthedoorunititcanbestoredinthe
chargerTF04L(optionalaccessory:Art.Nr.34238).
8. Installationandconnection
8.1 Doorunit
Labellingthenamecard
Installingabattery-operateddoorunit
Installinga12Vdoorunit
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!