User manual

GB-60
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
Route the wire ends of the connecting cable through the lead-through
and the cable hole [18], as described in fig. C (12 V supply) and fig. D
(12Vsupplyanddoorrelease).
Connect the wire ends to the terminals of the door unit as described in
fig.CandD.
Place the rubber cover back onto the door unit, and route the wires
throughtheslotsinthe rubbercover.
Slidethedoorunitontothebracket.
Screwthetorxscrew[23]firmlythroughthehole[19]intothehole[12],
usingthesuppliedtorxwrench[24].
Removethefourcoverscrewsfromtherelaymodule.
Takethecover[37]offtherelaymodule.
Routeallconnectedwiresthroughthehole[32]intherelaymodule.
Connect the wire ends to the respective terminals PGND [34], POWER
[33],CTRL[31]andSGND[30].
Connect the two wire ends of a suitable 12 V DC power supply to the
terminalsPGND[34]andPOWER[33]intherelaymodule.
UseacablestrandtoconnecttheterminalPOWER[33]andtheterminal
LOCK+[35]intherelaymodule.
Route a cable through the hole [32] of the relay module and use it to
connecttheterminalPGND[34]intherelaymodulewithoneterminalof
thedoorrelease.
Route a cable through the hole [32] of the relay module and use it to
connect the terminal LOCK- [36] in the relay module with the other
terminalofthedoorrelease.
SettheNO/NCswitch[29]toNO.
Turn the time regulator [28] with a small screwdriver to select a time
between1 second andapprox. 9 seconds.Pressthe hash key [45]for at
least 3 seconds. The door release will unlock for the selected time, and
your visitor can open the door within this time. Replace the cover onto
therelaymodule.
For the telephone function, use the telephonecable [62]to connect the
telephone cable connection [61] at the base with the telephone
connectioninyourresidence.Ifnecessary,usetheTAEadapter[63].
Connect the low-voltageplug ofthe supplied mainsadapter [64] tothe
mainsadapterconnector[60]ofthebase.
Placethebaseinthedesiredlocation.
Removethebatterycompartmentcover[55]fromthehandset[39].
Insert the two supplied AAA Ni-MH batteries into the battery
compartment[53]ofthehandset.Payattentiontothecorrectpolarity.
8.2 Optional connection of the relay module and a
doorrelease(see fig.D)
8.3 Base/Handset
!
!
!
!
!
Slidethebatterycompartmentcoverbackontothehandset.
Place thehandset onthe base so that the charging contacts [47] ofthe
handsettouchthechargingcontacts[57]ofthebase.
Connectthemainsadapterof the base to the power supply. The handset
willbeeptwice.
Thebatteries inthehandsetare charged automaticallyafterthehandset
has been placed in the connected base.
Watch the battery
charge indicator on the display display [41] (three black bars =
batteries are fullycharged, oneblack bar =very low batterypower). If
the batteriesdo notreach theirfull capacity after charging, they should
be replaced. When you place the handset in the base, it automatically
turnson.
Ifdesired,connect the 12 V power supply ofthe door unit. Afterthe door
unithassoundedtwice,thehandsetwillring.
Pickupthehandsetandthenplaceitbackinthebase.
Nowthewirelessdoorintercomisreadyforoperation.
When the handset is in power off mode and you place it in the base, it
automaticallyturnson.
Toturnthehandsetonoroffinstandbymode,followthesesteps:
1. Toturn the handset on,press and hold the key, until thedisplay is
switched on. While the handset searches for a base, the signal icon will
flashandthefollowingmessagewillbedisplayed:
Whenthehandsethasfoundthe base, it will enter the standby mode, the
displaywill show the name ofthe handset, signal icon, batteryicon
and current time.
If the battery power is very low when you place the handset in the
base,thedisplaywillshowthechargingofthebattery.
2. Toturn off the handset, keep the key pressed, until the displayis
switchedoff.
9. Operation
10. Turning the handset on/off
The batteries should be fully
charged for about 15 hours before initial operation.
Note:
YOUSHOULDFULLYCHARGETHEHANDSETBEFOREUSING.
The keys anddisplay illuminate whenthe handset isremoved from thebase
and also whena key is pressed. Theillumination stops automatically aftera
periodof10secondswithoutakeybeingpressed.
,date
If the handset is unsuccessful in finding a base, the
handsetwillbehaveaccordingtotheOutofRangecondition.
Searching...
Menu
Redial