(PC Connection Manual) Viewing Your Digital Camera Images On Your PC
Introduction This booklet explains how to view the images you took with the PENTAX Optio 33L on your PC. Keep this manual in a safe place. Regarding copyrights Images taken using the Optio 33L that are for anything other than personal enjoyment cannot be used without permission according to the rights as specified in the Copyright Act.
Contents Introduction..............................................................................................2 Contents ..................................................................................... 3 Viewing Images on a Windows PC 4 Software Provided ..................................................................... 4 System Requirements ............................................................... 4 Installing the Software..............................................................
Viewing Images on a Windows PC You can use the provided USB cable (I-USB2) or a card reader to transfer your images to the PC, and you can edit and print your images using the image viewing software. Here, the method for viewing images with the provided software (S-SW8) is explained. WINDOWS Software Provided The following software is included in the CD-ROM (S-SW8) provided.
Installing the Software 1 Install the required software as follows. On Windows 2000 or Windows XP, login as an administrator before installing the software. See your PC user's manual for login instructions. Turn on your PC. Place the provided CD-ROM (S-SW8) in your PC CD-ROM drive. The [PENTAX Software Installer] screen is displayed.
With the camera turned off, connect the camera to the PC using the USB cable. Confirm that the CF card is inserted in the camera. WINDOWS 7 Turn on the camera. The desktop screen will display [Found new hardware] (Windows XP) or [New Hardware Found] (Windows 98/98SE/2000), and the USB driver will be installed. 8 Double-click [My Computer] on the Desktop screen. When the installation is complete, the camera is recognized as a [Removable disk].
Installing ACDSee™ Once ACDSee™ is installed, you can edit and manage your pictures on your PC. Follow steps 1 through 3 on page 5 to display the [PENTAX Software Installer] screen. 4 Click [ACDSee™]. Installing ACD photostitcher WINDOWS The Setup screen is displayed. Follow the instructions on the screen to input registration information and install the software. When installation is complete, reboot your computer. ACD photostitcher is only for the English version and the Japanese version.
Displaying and Copying Images Using ACDSee™ 1 2 Turn on your PC. With the camera turned off, connect the camera to the PC using the USB cable. Confirm that the CF card is inserted in the camera. WINDOWS 3 Turn on your camera. ACDSee™ will start automatically, and display an image list. Proceed to step 5. 4 If ACDSee™ does not start automatically, double-click the ACDSee™ icon on the Desktop screen. The camera is recognized as a [Removable Disk] in [My Computer].
6 Copy images to your PC. Select an image to copy from the image list, and copy it to the destination folder. For details on copying procedures, see the user’s manual for your PC. You can copy images on Explorer as well, which is bundled with Windows. ACD photostitcher is only for the English version and the Japanese version. With ACDSee™ and ACD photostitcher installed, you can panorama stitch the images you took in Panorama Assist mode.
3 Correct the image positioning. ACD photostitcher starts, and the selected images are displayed in panorama format. Move the mouse pointer onto the image. It changes into a e symbol. Hold down the left mouse button and drag the images to adjust the stitching position. When the position is adjusted, click the [STITCH] button. WINDOWS 2 Click the [STITCH] button. 1 Click and drag to adjust position 4 Select the stitching method. You can choose the stitching method from [Big Plane] and [Cylinder].
5 Trim the image. Move the mouse pointer onto an image. It changes into a symbol. Hold down the left mouse button and drag the dotted lines to adjust the image trimming position. When the position is adjusted, click the [Trimming] button. 1 Trim the image. 6 WINDOWS 2 Click the [Trimming] button. Save the image. After confirming your trimming, click the [Save] button to save the image. To cancel the trimming, click the [Cancel Trimming] button. When you are done, close ACD photostitcher and ACDSee™.
Disconnecting your Camera from your PC Windows 2000/Me 1 Double-click the [Unplug or eject hardware icon] in the task bar recognized area. WINDOWS The [Remove Hardware] screen will appear. 2 Confirm that [Pentax USB Disk Device] is selected and click [Stop]. The [Stop Hardware Device] screen will appear. 3 Confirm that [Pentax USB Disk Device] is selected and click [OK]. A message will appear. 4 5 12 Click [OK]. Turn off the camera and disconnect the USB cable from your camera and your PC.
Windows XP Double-click the [Safely Remove Hardware] icon in the task bar recognized area. 2 Click [PENTAX USB DISK Device] and click [Stop]. 3 Click [PENTAX USB DISK Device Drive] and click [OK]. 4 When a message is displayed permitting removal, turn the camera off and disconnect the USB cable from your camera and PC. WINDOWS 1 Windows 98/98 SE There is no hot plug icon in Windows 98/98 SE. To disconnect the camera, simply turn off the camera and disconnect the USB cable.
Viewing Images on a Macintosh You can use the provided USB cable (I-USB2) or a card reader to send your images to the PC, and you can edit and print your images using the image viewing software. Here, the method for viewing images with the provided software (S-SW8) is explained. Software Provided The following software is included in the CD-ROM provided. • USB driver • Image viewing software (ACDSee™) System Requirements • • • • • OS: Mac OS 8.6 or higher (requires QuickTime 4.
6 Click your applicable language. The software installation selection screen will appear. Installing the USB Driver (Mac OS 8.6 only) 7 Click [USB Driver]. The USB driver is installed. When installation is complete, reboot your Macintosh. The provided USB driver does not need to be installed on Mac OS 9.0 or higher. Installing ACDSee™ 7 Click [ACDSee™]. The Setup screen is displayed. Follow the instructions on the screen to input registration information and install the software.
Displaying and Copying Images Using ACDSee™ 1 2 Turn on your Macintosh. With the camera turned off, connect the camera to the Macintosh using the USB cable. Confirm that the CF card is inserted in the camera. 3 Turn on your camera. The camera is recognized as an [untitled] on the desktop. The folder name can be changed. MACINTOSH 4 5 6 Click the [ACDSee™] on the hard drive. Double-click the [ACDSee™] program icon. Open the camera folder with ACDSee™.
8 Copy images to your Macintosh. See your Macintosh user’s manual for how to copy or move files. Please copy images to your Macintosh before editing them. If the CF memory card has a volume label, the volume label name will be displayed instead of “untitled”. A new CF card unformatted on the camera may show the manufacturer name or model number. Disconnecting your Camera from your Macintosh 1 Drag [untitled] (or the volume label name on the CF card) to your trash.
Memo
Memo
PENTAX Corporation 2-36-9,Maeno-cho, Itabashi-ku, Tokyo 174-8639, JAPAN (http://www.pentax.co.jp/) PENTAX Europe GmbH (European Headquarters) Julius-Vosseler-Strasse, 104, 22527 Hamburg, GERMANY (HQ - http://www.pentaxeurope.com) (Germany - http://www.pentax.de) PENTAX U.K. Limited PENTAX House, Heron Drive, Langley, Slough, Berks SL3 8PN, U.K. (http://www.pentax.co.uk) PENTAX France S.A.S. 12/14, rue Jean Poulmarch, 95106 Argenteuil Cedex, FRANCE PENTAX Benelux B.V.