Instructions / Assembly

6
AIR CONDITIONER FEATURES (CONTINUED)
TO ADJUST THE FAN SPEED:
SLEEP FEATURE:
Press Sleep button to initiate the sleep mode. In
ENERGY SAVER FEATURE:
FOLLOW ME FEATURE:
Light
flashing
Follow
Me
TIMER: AUTO START/STOP FEATURE:
Press to select one of four fan speeds: “Auto,”
“Low,” “Med” or “High.” Each time the button is
pressed, the fan speed mode is shifted. On “Dry”
mode the fan speed is set at low automatically.
Press Energy Saver button to initiate this
function. This function is available on “Cool
,” “Dry,”
and “Auto” (only Auto-Cooling and Auto-Fan)
modes. In this mode, the fan will continue to run for
3 minutes after the compressor shuts off. The fan
then cycles on for 2 minutes, at 10 minute intervals,
until the room temperature is above the set
temperature, at which time the compressor turns
back on and cooling starts.
To activate the Follow Me feature, point the remote
control towards the unit and press the “Follow Me”
button. The remote displays the actual temperature at
its location. The remote control will send this signal to
the air conditioner every 3 minutes until the Follow Me
button is pressed again. If the unit does not receive the
Follow Me signal during any 7 minute interval, the unit
will beep to indicate the Follow Me mode has ended.
The actual temperature can be displayed at the unit by
pressing the “Fan” only mode. When in the “Cool”
mode, the unit display indicates the set temperature.
This feature can ONLY be activated
from the remote control. The
remote control serves as a remote
thermostat allowing for precise
temperature control at its location.
When the unit is on or off, first press Timer button.
The TIMER ON indicator light illuminates. It indicates the
Auto Start program is initiated.
When the time of TIMER ON is displayed, if you press the
Timer button again, the TIMER OFF indicator light
illuminates. It indicates the Auto Stop program is initiated.
Press or hold the UP or DOWN button to change the Auto
time by 0.5 hour increments, up to 10 hours, then by 1
hour increments, up to 24 hours. The control will count
down the time remaining until start.
The selected time will register in 5 seconds and the
system will automatically revert back to display the
previous temperature setting or the room temperature
(depending on whether the unit is powered on or off and
the mode it is in).
Turning the unit ON or OFF at any time or adjusting the
timer setting to 0.0 will cancel the Auto Start/Stop program.
A NOTE ABOUT THE TIMER: When you set the timer, the
unit will only go on once and off once. If you want the air
conditioner to cycle on and off based on desired room
temperature, you do not need to set the timer. Instead, set
your desired temperature and the unit will cycle on and off
based on that temperature setting.
TO SELECT THE OPERATING MODE:
To choose operating mode, press the Mode button.
Each time you press the button, a mode is selected in
a sequence that goes from “Auto,” “Cool,” “Dry,” and
“Fan.” The indicator light will be illuminated and remain on
once the mode is selected. The unit will automatically
initiate the Energy Saver function under “Cool,” “Dry,”
and “Auto” (only Auto-Cooling and Auto-Fan) modes.
To operate on “Fan” only:
Use this function only when cooling is not desired, such as
for room air circulation or to exhaust stale air. You can
To operate on “Auto” feature:
When you set the air conditioner in “Auto” mode, it will auto-
matically select cooling, or fan only operation depending
on what temp
erature you have selected and the room
temperature. The air conditioner will control room
temperature automatically around the temperature you set.
In this mode, the fan speed cannot be adjusted. It starts
automatically at a speed according to the room temperature.
choose any fan speed you prefer. During this function, the
display will show the actual room temperature, not the set
temperature as in the cooling mode. Temperature cannot
be adjusted in “Fan” only mode.
To operate on “Dry” mode:
In this mode, the air conditioner will reduce air
humidity. If the space is a closed or sealed area, some
degree of cooling will continue.
this mode the selected temperature will increase
(cool) by 2ºF / 1ºC 30 minutes after the mode is
selected. The temperature will then inc
rease (cool) by
another 2ºF / 1ºC after an additional 30 minutes. This
new temperature will be maintained for 6 hours before
it returns to the originally selected temperature. This
ends the Sleep mode and the unit will continue to
operate as originally programmed. The Sleep mode
program can be canceled at any time during operation
by pressing the “Sleep” button again.
Press Check Filter button to initiate this feature.
This feature is a reminder to clean the Air Filter for
more efficient operation. The LED (light) will illumi-
nate after 250 hours of operation. To reset after
cleaning the filter, press the “Check Filter” button
and the light will go off.
CHECK FILTER FEATURE: