Installation Guide

ManualsBrandsPerfect Pitch ManualsPlumbing Product1/2 in., 3/4 in. and 1 in. Adjustable Drainage Installation Kit with Universal Clamps (5-Pack)

www.PITCHTOCODE.com

MADE IN USA

CONTENTS

Instruction

Sheet

Universal

Pipe Clamps

Standoffs

HARDWARE & TOOLS NEEDED

Screws

Drill

4. Repeat steps 1-3 on all

additional intervals to maintain

proper pitch during installation.

* Arrow indicators on the Universal Pipe Clamp rotate depending on orientation of clamp.

** Consult your local and federal building code as well as equipment manufacturer instructions for exact requirements.

NOTE: Some installation runs exceed 60 feet (18 meters) for condensate, 32 feet (9 meters) for waste. In these cases,

Standoffs can be stacked using dovetails provided.

1. Align Universal Pipe Clamp to

Standoff using the ruler

indicator*, snap Universal Pipe

Clamp onto Standoff at pitch

interval needed to meet local,

state or federal building code

requirements**. Ensure teeth on

Universal Pipe Clamp snap into

teeth on Standoff.

2. Secure Standoff base onto

substrate (i.e. ﬂoor or ceiling

joists, plywood, etc.) in

appropriate location per building

code. Use minimum of two

screws in opposing slots provided

for better stability. Four screws

are recommended for all

standoffs.

3. Push pipe into side opening

on Universal Pipe Clamp to

secure.

ENGLISH INSTRUCTIONS

ADJUSTABLE FASTENING SYSTEM

5x 5x 1x

SCAN TO GO ONLINE

WITH YOUR SMARTPHONE!

Summary of content (4 pages)

PAGE 1
ENGLISH INSTRUCTIONS MADE IN USA www.PITCHTOCODE.com ADJUSTABLE FASTENING SYSTEM CONTENTS HARDWARE & TOOLS NEEDED SCAN TO GO ONLINE Drill Universal 5x Standoffs 5x Pipe Clamps 1x Sheet Instruction 1. Align Universal Pipe Clamp to Standoff using the ruler indicator*, snap Universal Pipe Clamp onto Standoff at pitch interval needed to meet local, state or federal building code requirements**. Ensure teeth on Universal Pipe Clamp snap into teeth on Standoff. 3.
PAGE 2
ENGLISH INSTALLATION WALKTHROUGH ADJUSTABLE FASTENING SYSTEM Before installation, please refer to codes and Equipment Manufacturer Requirements. Measure distance from source FIG. A (ie. Air Handler, Condensing Furnace, Drip Pan, etc.) To the termination point. (i.e. Outside, Condensate Pump, Basin, etc.) For this example: Piping for this application is 3/4 inch PVC. The pipe needs to be supported and secured every 4 feet (per code). The pitch minimum is 1/8 inch per foot for condensate.
PAGE 3
Instrucciones en español Hecho en EE.UU. ADJUSTABLE FASTENING SYSTEM CONTENIDOS www.PITCHTOCODE.com HERRAMIENTAS Y ACCESORIOS NECESARIOS Taladre 5x Universal Standoffs 5x Pipe Clamps 1x Instrucciones Hoja de 1. Utilice el indicador de regla para alinear Universal Pipe Clamp a Standoff,*Ajustar Universal Pipe Clamp en Standoff para cumplir los requisitos del código de construcción local, estatal o federal**. Asegúrese de que los dientes de la Universal Pipe Clamp encaja en los dientes en Standoff.
PAGE 4
Tutorial de instalación españoles ADJUSTABLE FASTENING SYSTEM Por favor, consulte los códigos y requisitos del fabricante del equipo antes de la instalación. Mida la distancia desde la fuente. FIG. A (es decir, Manejador de aire, bomba condesadora, bandeja de goteo, etc...) Hasta el punto de terminación. (es decir. Afuera, La bomba de condensado, Cuenca, etc...) Para este ejemplo: Tuberías para esta aplicación es 3/4 pulgadas de tubería de PVC.