User manual

SOFTWARE VERSION
The software display cannot be altered and is just for your reference. You can only view
the software version in DAB and FM mode.
1. Press the On/Off button to switch on the radio.
2. Press the Source button to select FM or DAB mode.
3. Press the Menu button until the display shows “Full Scan”, and then rotate the
Tuning knob until the display shows “System”.
4. Press the Tuning knob; rotate the Tuning knob until the display shows “SW
version”.
5. Press the Tuning knob to view the software version.
6. Press the Tuning knob to back to last menu and press menu to return to the
normal radio display.
Note: USB socket inside battery compartment is for upgrading the software of the device
if needed.
SYSTEM RESET
If the radio fails to operate correctly, or some digits on the display are missing or
incomplete, carry out the following procedure.
1. Press the On/Off button to switch on the radio.
2. Press the Menu button,
3. Rotate the Tuning knob until the display shows “System”. Press the Tuning knob.
4. Rotate the Tuning knob until the display shows “Factory reset”. Press the Tuning
knob.
5. Rotate the Tuning knob to select between “Yes” or “No”. Select “Yes” if you wish to
reset the radio, otherwise, select “No”.
6. Press the Tuning knob to cause the factory reset.
7. A full reset will be performed. All presets and the station list will be erased. All
settings will be set to the default values. The display will show “WELCOME TO
DIGITAL RADIO” for a few seconds, and then the radio will automatically perform
an auto scan of the Band III DAB channels and the FM band, the display will show
“Scanning” at DAB and “Auto” at FM.
In case of malfunction due to electrostatic discharge; reset the product as above to
resume normal operation. If you are not able to perform the reset operation as above,
remove and reconnect all batteries and the power supply.
BACKLIGHT
When the radio is in operation or in standby, pressing any button will illuminate the LCD
display for approx. 10 seconds.
ATP PASSCODE
ThisradioisequippedwithanAnti-Theft-Protectionsystem(ATPsystem).Whenthe
ATP system is enabled, a passcode is required for turning on the radio.
1. Press the On/Off button to turn on the radio.
2. Press the Menu button.
3. Rotate the Tuning knob until the display shows “System”. Press the Tuning knob.
4. Rotate the Tuning knob until the display shows “Passcode”. Press the Tuning
knob. “Enable” or “Disable” will be displayed, to enable ATP, turn and press Tuning
knob to select “Enable”.
5. “Change Passcode” will be displayed, enter a 4-digits numeric passcode by
 pressingthepresetbuttons(1-10)
6. “ConrmPasscode”willbedisplayed.Enterasecondtimethesamepasscodeto
 conrm.
7. To disable passcode, select “Disable” as previously showed. And re-enter the
previous passcode to disable the lock.
When ATP is enabled, and if wrong passcode is entered for three times, a timer will be
activated. The next attempt will be possible only after the timer has elapsed. The timer
period will be increased with further wrong passcodes.
WARNING: If you choose to activate the passcode, please note your passcode
somewhere safe as a memory back-up in case you should forget it. This is
strongly advised, as there is no way to reset the radio should the passcode be
forgotten!
WARRANTY
This radio has a 2 year limited warranty.
WARNING ! Warranty becomes void once the radio cabinet has been opened or any
modicationsoralterationstotheradiohavebeenmade!
The terms of the warranty of this radio do not cover the following:
- Damage caused by misuse, abuse, neglect, alterations, accidents or unauthorised
repair.
- Normal wear and tear.
- Breaking or bending of the metal telescopic antenna.
- Batteries.
19 20
GB
GB