User manual

Redialing your last dialed phone number (of a paired mobile phone)
The Hands-Free-Calling feature allows you redialing your last dialed phone number on
yourmobilephone(Bluetoothmodeonly).
1. In Bluetooth mode.
2. Press and hold the Tuning knob (Phone icon) on the right for more than 2
seconds. The last dialed phone number on your mobile phone will be redialed.
3. Adjust the volume by turning the Volume knob if necessary.
4. Press the Tuning knob (Phone icon) again to hang up the phone call.
Bluetooth Options
The Bluetooth function can be set to operate in different ways as below:
1. In Bluetooth mode, press the Menu button to enter the system setting.
2. Rotate the Tuning knob until “Bluetooth” is displayed; press the Tuning knob.
3. Rotate the Tuning knob to select “BT always on”, “BT mode only” or “Disconnect
BT” options, and press the Tuning knob to select the setting.
a. BT always on Bluetooth is turned on when the Handsfree radio is on. You
can playback music in the Bluetooth mode and use the
Hands-Free-Calling feature to answer incoming phone calls
in all operation modes, for example, also when you are
listening to the radio. As an indication, the blue Bluetooth
connected LED will be on in all operation modes (FM, DAB,
  BluetoothandAUXIN).
b. BT mode only Bluetooth is turned on only in Bluetooth mode. You can
playback music and use the Hands-Free-Calling feature to
answer incoming phone calls in the Bluetooth mode only.
As an indication, the blue Bluetooth connected LED will be
on only in the Bluetooth mode.
c. Disconnect BT Bluetooth will be disconnected from your mobile phone
and enter the “discoverable mode” (The blue Bluetooth
connected LED will start blinking until a new pairing is
  established).ThisistoallowtheBluetoothpairingtoanother
device. If no new device is paired, the Bluetooth will
automatically try to connect to the last device when it is
switched off and on again.
Note:Thevolumesettingsofyourmobilephoneinuencethevolumeofthemusic
streaming and the volume of the incoming phone calls on the Handsfree radio.
The Auto-Power management function will be activated in Bluetooth mode. If there
is no signal from Bluetooth for a period of over 15 minutes, the Handsfree radio will
automatically switch to standby mode. Pressing the On/Off button will wake up the unit.
CHARGING A MOBILE PHONE
The USB socket on the left side can provide DC power of 5V/0.5A for charging a mobile
phone. Connect the mobile phone to the USB socket with an appropriate cable (not
includedwiththisradio).TheUSBpowerisavailableinallmodes,includingstandby
mode.
Refer to the user manual or the manufacturer of the mobile phone to verify if it supports
charging from an USB power.
The USB socket is suitable for DC power-out only and cannot be used for e.g. playback
of music from a USB stick.
Warning: Never use the USB socket in rainy or moist conditions to prevent moist from
entering the radio and so to prevent potential short circuit. Always keep the rubber cover
well closed under these conditions.
It is recommended to use AC power while charging a mobile phone via USB socket. On
DC power it is also possible to charge a mobile phone from the USB socket, however
using DC power to charge a mobile phone will consume energy from the batteries and
so drain the batteries easily.
AUX IN MODE
A 3.5mm stereo Aux-In socket is provided on the side behind the rubber cover, for
connecting an external audio device such as MP3 player or CD player (Aux cable not
includedwiththisradio).
1. Connect an external player to the Aux-In socket.
2. Press the Source button to select AUX input. Display will show “AUX IN”.
3. Play the external player.
4. Adjust the volume both the radio and the player for comfortable listening.
5. After use, close the rubber cover to prevent moist or dust from entering into the
sockets and radio.
Notes: Never use the Aux-In socket in rainy or moist conditions to prevent moist from
entering the radio. Keep the rubber cover well closed under these conditions.
The Auto-Power management function will be activated in AUX IN mode. If there is no
signal* from the Aux-In socket for a period of over 15 minutes, the Handsfree radio will
automatically switch to standby mode. Pressing the On/Off button will wake up the unit.
* Also when the incoming signal from the external device is too low and cannot be
detected for a period of over 15 minutes by the Auto-Power management, the Handsfree
radio will switch to standby mode.
To prevent this raise the output level of the external device enough to be detected.
15 16
GB
GB