MSDS

ManualsBrandsPerformix Brand ManualsPaint14.5 oz. Yellow Rubber Coating (6-Pack)

*Estimate

N/A-Not Applicable

N/R-Not Restricted

N/E-Not Established

MATERIAL SAFETY DATA SHEET

NOTE: BLANK SPACES ARE NOT PERMITTED. IF ANY ITEM IS NOT APPLICABLE, THE SPACE MUST BE MARKED TO INDICATE THAT.

IDENTITY

(As shown on Label or package) 14.5 Fluid Ounce PLASTI DIP

PART NO.

IF APPLICABLE

SECTION I

MANUFACTURER'S

NAME Plasti Dip International, Inc.

EMERGENCY

PHONE No. 1-800-424-9300

ADDRESS (NUMBER, STREET, CITY, STATE AND ZIP CODE)

3920 Pheasant Ridge Drive

REVISION #

Blaine, MN 55449

MANUFACTURER'S PHONE

No. FOR INFORMATION 1-763-785-2156

DATE MSDS

WAS PREPARED December 29, 2011

SECTION II - HAZARDOUS INGREDIENTS INFORMATION. All Health Hazards which comprise 1% or greater of the composition and all

carcinogens if 0.1% of the composition or greater.

HAZARDOUS COMPONENTS CHEMICAL and

IDENTITY AND COMMON NAME (S)

% Wt.

(OPTIONAL)

CAS NO. OSHA

PEL

ACGIH

TLV

OTHER LIMITS

RECOMMEND

VM&P Naphtha 32-38 64742-89-8 300 ppm 300 ppm None

Hexane 16-19 110-54-3 500 ppm 50 ppm None

Toluene 13-16 108-88-3 200 ppm 50 ppm None

Methyl Ethyl Ketone 3-7 78-93-3 200 ppm 200 ppm None

Resins 25-27 N/A N/A N/A None

SECTION III - PHYSICAL / CHEMICAL CHARACTERISTICS

BOILING

POINT 149 - 285°F

SPECIFIC GRAVITY (H

0 =1)

0.79 - 0.83

APPROXIMATE WEIGHT PER GALLON (LBS)

6.60-690

VAPOR PRESSURE

125 mmHg @ 20°C

VAPOR DENSITY

(AIR = 1) Heavier than air

EVAPORATION RATE

(BUTYL ACETATE =1) > 1.0

SOLUBILITY IN WATER

Insoluble

% VOLATILE 72-75%

VOC LBS./GAL 4.8-5.2

OTHER

(IF ANY) None

APPEARANCE

AND ODOR Various Colors, Honey Like Substance - Characteristic Odor

SECTION IV-FIRE AND EXPLOSION HAZARD DATA

FLASH POINT -10.0°F

(METHOD USED) TCC

FLAMMABLE LIMITS

0.9 – 11.5

LEL

0.9

UEL

11.5

EXTINGUISHING

MEDIA Carbon Dioxide, Dry Chemical, or Foam

SPECIAL FIRE

FIGHTING PROCEDURES Self contained breathing apparatus with a full face piece, operated in pressure demand or other positive pressure mode.

UNUSUAL FIRE AND

EXPLOSION HAZARDS This material is flammable and may be ignited by heat, sparks, flame or static electricity.

HAZARDOUS PRODUCTS FORMED BY

FIRE OR THERMAL DECOMPOSITION Carbon Dioxide and/or Carbon Monoxide.

EXPLOSIVE LIMITS

(% BY VOLUME IN AIR) 0.9 - 11.5

SECTION V - OPTIONAL HAZARD RATINGS IDENTIFICATION

HAZARD RATING

4-EXTREME

3-HIGH

2-MODERATE

1-SLIGHT

0-INSIGNIFICANT

**SEE SECTION IV

National Fire Protection Association (NFPA)

FIRE 3 REACTIVITY 0 .

HEALTH 2 SPECIAL HAZARDS None .

This is the "front" when printed in duplex. Page 1 of 2 pages if not duplex.

Summary of content (2 pages)

PAGE 1
*Estimate N/A-Not Applicable N/R-Not Restricted N/E-Not Established MATERIAL SAFETY DATA SHEET NOTE: BLANK SPACES ARE NOT PERMITTED. IF ANY ITEM IS NOT APPLICABLE, THE SPACE MUST BE MARKED TO INDICATE THAT. IDENTITY PART NO. IF APPLICABLE (As shown on Label or package) 14.5 Fluid Ounce PLASTI DIP SECTION I MANUFACTURER'S EMERGENCY NAME Plasti Dip International, Inc. PHONE No.
PAGE 2
SECTION VI - REACTIVITY AND STABILITY DATA STABILITY UNSTABLE STABLE X CONDITIONS TO AVOID None INCOMPATIBILITY (Materials to Avoid) Strong acids, bases, oxidizing agents, selected amines with alkali metals and halogens. HAZARDOUS DECOMPOSITION OR BY PRODUCTS Carbon Monoxide, Carbon Dioxide HAZARDOUS MAY OCCUR CONDITIONS TO AVOID None POLYMERIZATION WILL NOT OCCUR X SECTION VII - HEALTH HAZARD DATA ROUTES OF ENTRY INHALATION? Yes SKIN? Yes INGESTION? Yes EYES? Yes See Signs and Symptoms of Exposure below.