Project Ideas

ManualsBrandsPergo ManualsFlooringOutlast+ Marigold Oak 10 mm Thick x 7-1/2 in. Wide x 47-1/4 in. Length Laminate Flooring (549.64 sq. ft. / pallet)

Although originally designed as a durable ﬂoor covering, many consumers have started using Pergo laminate ﬂooring on

walls to give their rooms more character and to create a feature or accent wall.

Laminate can be utilized as a decorative covering over an existing clean, dry, secure and vertical wall that meets

building codes. The wall substrate should be primed or painted drywall (gypsum board) only. Do not install directly over

wallpaper or paneling. Laminate is not intended to be used on ceilings, countertops or as any type of structural material.

The installation wall should only run vertical to the ﬂoor. Sloping walls and surfaces that are parallel to the ﬂoor, such as

ceilings or sots, should not be selected. Limit installations to a maximum of 40 feet in length and a maximum of 1 plank

length in height.

Laminate is suitable for an accent wall when used in climate controlled (35-65% RH and 60-85° F) indoor installations

only. Acclimate unopened product lying ﬂat in the room where it is to be installed for at least 48 hours. Mix planks from

dierent cartons as you install to maximize the natural appearance.

Check wall for moisture, visible water stains or leaking windows. Do not install laminate over a wall with known moisture

damage. Do not install in areas near water sources such as a backsplash over a sink or bathtub. Acceptable job site

conditions, including relative humidity and wall moisture conditions, must be maintained throughout the life of the

laminate application.

Check wall for ﬂatness within 3/16" over 10 feet. Correct any unevenness before installing to allow the laminate planks to

lie ﬂat without rocking.

The following requirements are not intended to supersede federal, state or local building codes, but as with many other

interior ﬁnish products, may require modifying existing structural components for successful installation. Owner assumes

responsibility for compliance with all building codes, including maintaining the required distance from heat sources such

as ﬁreplaces.

WARNING: For a safe and secure installation, this product MUST be installed in accordance with these installation

instructions.

PERGO Outlast+ Laminate Flooring on Wall Install Instructions

Tools Required for Installation:

• Caulk gun

• Utility knife

• Stud ﬁnder (electronic)

• Carpenters level or laser level

• Chalk line

• 18 gauge brand nail guin (electric or air)

• Tape measure

• Pencil

• Screw gun or drill driver (for horizontal installation

only)

• Safety glasses

• Dust mask

• Gloves

Materials Required for Installation:

• 1½" - 1¾" brad nails

• 100% silicone adhesive caulk (clear)

• 1½" - 1¾" dry wall screws (for horizontal installation

only)

• Painters tape (for horizontal installation only)

Other Tools and Materials:

• Step ladder (for horizontal installation only)

• Hammer

• Uniclic® appropriate tapping block

• Pull bar

• Saw for cutting laminate planks

• Pry bar (for removing existing base or trim)

• Chair rail (for vertical installation only), wall base and

quarter round moldings (to fame out accent wall)

2020_06_OP_THD

Summary of content (7 pages)

PAGE 1
PERGO Outlast+ Laminate Flooring on Wall Install Instructions Although originally designed as a durable floor covering, many consumers have started using Pergo laminate flooring on walls to give their rooms more character and to create a feature or accent wall. Laminate can be utilized as a decorative covering over an existing clean, dry, secure and vertical wall that meets building codes. The wall substrate should be primed or painted drywall (gypsum board) only.
PAGE 2
PERGO Outlast+ Vertical Wainscot Style Wall Install Instructions 1. Measure the length of your laminate plank and the length of the wall area to determine the total square footage area. Order that amount of flooring plus an additional 10% for incorrect cuts. 2. Remove all base and trim from accent wall. Measure from the floor a distance equal to your laminate plank plus one inch then level and mark the wall with a chalk line. With an electronic stud finder locate and mark wall studs. (Figure 1) 3.
PAGE 3
PERGO Outlast+ Vertical Wainscot Style Wall Install Instructions 8. Apply silicone adhesive to the back side of the plank in an “S” pattern. If you’re using a laminate plank with an attached pad, apply the silicone directly to the pad on the back of the plank. (Figure 3) 9. Adhere the plank to the wall leaving a 3/16" gap (A) from the corners of the wall and a 1" gap (B) at bottom. Drive brad nails ½" from the top and bottom of each plank to secure to wall. Place nails where the trim will cover. 10.
PAGE 4
PERGO Outlast+ Horizontal Accent Wall Install Instructions 1. Measure the length and width of the wall area to determine the total square footage area. Order that amount of flooring plus an additional 10% for incorrect cuts. 2. Remove baseboards from the accent wall and locate the wall studs using the stud finder tool. Mark vertical lines over all studs. Use painters tape to extend stud location to ceiling if needed. (Figure 1) 3. Turn off power while working around wall outlets and light switches.
PAGE 5
PERGO Outlast+ Horizontal Accent Wall Install Instructions 9. Drive a brad nail into each plank at each wall stud through the shallow area of the extended groove (see inset diagram). Take care that the brad nail heads are not raised, but also don’t force them all the way through the groove. This will allow easy connection of the next row of planks.
PAGE 6
PERGO Outlast+ Horizontal Accent Wall Install Instructions 13. Repeat this process for each plank working your way up to the last row. (Figure 8) 14. For the last row of the installation, use painters tape to mark the stud location for brad nailing. Cut all planks in the last row to the required width to complete the installation. Complete the installation as you have the earlier rows. (Figure 8a) 15. Use quarter round for inside corners and ceiling. Finish with wall base board of your choice.
PAGE 7
PERGO Outlast+ Laminate Flooring on Wall Install Instructions Care and Cleaning Dry wipe as primary cleaning method. Occasionally damp wipe with water only. NO wet washing. If needed, use 1 cup of vinegar per gallon of water OR 1/3 cup non-sudsing ammonia per gallon of water. DO NOT use detergents, abrasive cleaners, soaps, waxes or polishes. Wipe off spills immediately. DO NOT allow moisture to remain on the product surface for longer than 30 minutes.