Installation Sheet
0212ES | 03/2021 | PAGE 7 OF 12
PERGO® IS MANUFACTURED AND DISTRIBUTED BY UNILIN NORTH AMERICA, LLC
CUSTOMER SERVICE | 1-800-33-PERGO | NA.PERGO.COM/CONTACT-US
Pergo Classics Installation Instructions
PERGO Timbercraft + WetProtect Vertical Wainscot Style Wall Install Instructions
7
2020_0425_TIM_INST
1. Measure the length of your laminate plank and the length of the wall area to determine the total square footage
area. Order that amount of flooring plus an additional 10% for incorrect cuts.
2. Remove all base and trim from accent wall. Measure from the floor a distance equal to your laminate plank plus
one inch then level and mark the wall with a chalk line. With an electronic stud finder locate and mark wall studs.
(Figure 1)
3. Turn off power while working around wall outlets and light switches. Pay special attention to avoid contact with
electrical wiring.
4. Inspect each plank for damage before installing. (Figure 1a) Do not install damaged planks. You can use laminate
planks with or without an attached pad. There is no need to remove the pad, so treat the installation the same for
both types of planks.
5. Start from the left side with the short side tongue up and long side groove toward the wall. Place one plank against
the wall and align at the top to test fit. You will want a 1" gap at the bottom of the plank. (Figure 2a)
6. Determine the appropriate number of vertical planks to fill the wall. For the best appearance, the first and last
planks should be approximately the same width. Cut them as needed based on the width of your installation and
the width of your planks.
7. If you don’t need to cut the first plank, remove lower extension of long side groove with saw or utility knife.
(Figure 2b)
55"
54"
1
Level Line
1" Gap
1a
2a
1" Gap
Install
towards
wall
after
before
Cut off
extension
2b
8. Apply silicone adhesive to the back side of the plank in an “S” pattern. If you’re using a laminate plank with an attached pad,
apply the silicone directly to the pad on the back of the plank. (Figure 3)
9. Adhere the plank to the wall leaving a 3/16” gap (A) from the corners of the wall and a 1” gap (B) at bottom. Drive brad nails 1/2”
from the top and bottom of each plank to secure to wall. Place nails where the trim will cover.
10. Continue with the installation for each subsequent plank by first applying silicone adhesive to the back side of the plank in an
“S” pattern. Then angle the groove over the tongue of the previous plank and wiggle into place. Tighten joints as needed with a
tapping block or pull bar. Finally, drive brad nails 1/2” from the top and bottom of each plank to secure to wall. Place nails where
the trim will cover. Be sure to drive the brad nails into a stud whenever possible.(Figure 4)
11. Finish wainscot accent to ending wall. (Figure 5)
12. Install trim (chair rail) over the top edge. Install quarter round in the corners. Finish by installing the baseboard of your choice.
(Figure 6)
PERGO Timbercraft + WetProtect Vertical Wainscot Style Wall Install Instructions
8
2020_0425_TIM_INST
8. Apply silicone adhesive to the back side of the plank in an “S” pattern. If you’re using a laminate plank with an
attached pad, apply the silicone directly to the pad on the back of the plank. (Figure 3)
9. Adhere the plank to the wall leaving a
3
/16" gap (A) from the corners of the wall and a 1" gap (B) at bottom. Drive
brad nails
1
/2" from the top and bottom of each plank to secure to wall. Place nails where the trim will cover.
10. Continue with the installation for each subsequent plank by first applying silicone adhesive to the back side of the
plank in an “S” pattern. Then angle the groove over the tongue of the previous plank and wiggle into place. Tighten
joints as needed with a tapping block or pull bar. Finally, drive brad nails
1
/2" from the top and bottom of each plank
to secure to wall. Place nails where the trim will cover. Be sure to drive the brad nails into a stud whenever possible.
(Figure 4)
11. Finish wainscot accent to ending wall. (Figure 5)
12. Install trim (chair rail) over the top edge. Install quarter round in the corners. Finish by installing the baseboard of
your choice. (Figure 6)
3
Silicone in
“S” pattern
3/16"
Gap
3/16"
Gap
5
1" Gap
A
Level Line
3/16"
Gap
4
Base Detail
Trim (chair rail)
Wainscot Accent
Laminate
F l o o r
6
Quarter round
PERGO Timbercraft + WetProtect Vertical Wainscot Style Wall Install Instructions
8
2020_0425_TIM_INST
8. Apply silicone adhesive to the back side of the plank in an “S” pattern. If you’re using a laminate plank with an
attached pad, apply the silicone directly to the pad on the back of the plank. (Figure 3)
9. Adhere the plank to the wall leaving a
3
/16" gap (A) from the corners of the wall and a 1" gap (B) at bottom. Drive
brad nails
1
/2" from the top and bottom of each plank to secure to wall. Place nails where the trim will cover.
10. Continue with the installation for each subsequent plank by first applying silicone adhesive to the back side of the
plank in an “S” pattern. Then angle the groove over the tongue of the previous plank and wiggle into place. Tighten
joints as needed with a tapping block or pull bar. Finally, drive brad nails
1
/2" from the top and bottom of each plank
to secure to wall. Place nails where the trim will cover. Be sure to drive the brad nails into a stud whenever possible.
(Figure 4)
11. Finish wainscot accent to ending wall. (Figure 5)
12. Install trim (chair rail) over the top edge. Install quarter round in the corners. Finish by installing the baseboard of
your choice. (Figure 6)
3
Silicone in
“S” pattern
3/16"
Gap
3/16"
Gap
5
1" Gap
A
Level Line
3/16"
Gap
4
Base Detail
Trim (chair rail)
Wainscot Accent
Laminate
F l o o r
6
Quarter round