Installation Guide

ManualsBrandsPergo ManualsFlooringClassic Auburn Oak/Royal Oak .75 in. Thick x 2.37 in. Wide x 78.7 in. Length Laminate 4-in-1 Molding

4 in 1 Molding for Flooring | English

Installation Instructions

Step 1

Review Installation Checklist

Do not push parts into track until ready to install in final position.

Do not remove from track once installed.

Use a new saw blade for best cutting results.

Depending on molding type, all parts may NOT be used.

Always install screws in end holes of track and then every other hole.

For concrete floors, drill hole using 3/16" (5mm) diameter drill, insert

plastic anchor, then use screw.

Attach the track directly to the subfloor (remove any padding or

underlayment).

Laminate flooring installations require the use of T-Moldings in

doorways 4 feet (1.22 meters) or less and in rooms 40 feet (12.2 meters)

or larger in length or width.

This product has been finished for you; do not sand or paint.

Summary of content (7 pages)

PAGE 1
4 in 1 Molding for Flooring | English Installation Instructions Step 1 Review Installation Checklist Do not push parts into track until ready to install in final position. Do not remove from track once installed. Use a new saw blade for best cutting results. Depending on molding type, all parts may NOT be used. Always install screws in end holes of track and then every other hole. For concrete floors, drill hole using 3/16" (5mm) diameter drill, insert plastic anchor, then use screw.
PAGE 2
4 in 1 Molding for Flooring | English Step 2 Choose Your Transition Type Kit allows assembly of four different molding options from one single product. A. T-Molding – transitions between equal height hard flooring surfaces. B. Carpet Transition – transitions from flooring to carpet. C. Hard Surface Reducer – transitions flooring to a lower surface (vinyl, wood, etc.) D. End Molding – finishes flooring at sliding doors, fireplaces and other fixed edges.
PAGE 3
4 in 1 Molding for Flooring | English Step 3 Install Your Moldings Detailed installation instructions on back Each individual package includes: Part # 1 Track Part # 2 Shim Part # 3 Screws Plastic Anchors* *(Use when installing on concrete subfloors
PAGE 4
in 1 Molding for Flooring | English Accommodates 7mm to 15mm Floor Thickness Total Height 7mm – 15 mm Plank Underlayment Subfloor Total Height = Plank + Underlayment 9/32" to 15/32" (7mm to 12 mm) Track only 15/32" to 9/16" (12mm to 14mm) Track plus snap on plastic shim 9/16" to 19/32" (14mm to 15mm) Track over reversed plastic shim
PAGE 5
4 in 1 Molding for Flooring | English A: T-Molding Use Part #1 1. Leave a 1-1/8" (29mm) space between flooring as shown. 2. Install track in position with screws as shown. Leave ¼" (6mm) expansion space on both sides of track. 3. Start at one end. Firmly push Part #1 down into track. 4. Continue to push down firmly into track, working from one end to the other. B: Carpet Transition Use Part #1 and Part #2 1. Leave a 1-3/8" (35 mm) space between laminate flooring and vertical edge as shown. 2.
PAGE 6
4 in 1 Molding for Flooring | English D: End Molding Use Part #1 and Part #2 1. Leave a 1-3/8" (35 mm) space between laminate flooring and vertical edge as shown. 2. Install track in position with screws as shown. Leave ½" (12mm) expansion space 3. 4. 5. 6. between the track and laminate flooring. Hold Part #1 and Part #2 together as shown. Start at one end and push down firmly into track while holding Part #1 and Part #2 together.
PAGE 7
4 in 1 Molding for Flooring | English