Workshop Manual
Table Of Contents
- Perkins 400 Series
- 1 General information
- 2 Specifications
- 3 Cylinder head assembly
- 4 Piston and connecting rod assemblies
- 5 Crankshaft assembly
- 6 Timing case and drive assembly
- 7 Cylinder block assembly
- 8 Engine timing
- 9 Aspiration system
- 10 Lubrication system
- 11 Fuel system
- 12 Cooling system
- 13 Flywheel and housing
- 14 Electrical equipment
- Wiring diagram 15 amp alternator - 403C-11 108
- Wiring diagram 40 amp alternator - 403C-11 109
- Wiring diagram 55 amp alternator 403C-15, 404C-22 and 404C-22T 110
- Automatic shutdown connector 111
- Wiring diagram - automatic shutdown 15 amp alternator - 403C-11 112
- Wiring diagram - automatic shutdown 40 amp alternator - 403C-11 113
- Wiring diagram - automatic shutdown 55 amp alternator 403C-15, 404C-22 and 404C-22T 114
- 15 Auxiliary equipment
- 16 Special tools
- General information
- Introduction
- Safety precautions
- POWERPART recommended consumable products
- POWERPART Antifreeze
- POWERPART Easy Flush
- POWERPART Gasket and flange sealant
- POWERPART Gasket remover
- POWERPART Griptite
- POWERPART Hydraulic threadseal
- POWERPART Industrial grade super glue
- POWERPART Lay-Up 1
- POWERPART Lay-Up 2
- POWERPART Lay-Up 3
- POWERPART Metal repair putty
- POWERPART Pipe sealant and sealant primer
- POWERPART Radiator stop leak
- POWERPART Retainer (high strength)
- POWERPART Safety cleaner
- POWERPART Silicone adhesive
- POWERPART Silicone RTV sealing and jointing compound
- POWERPART Stud and bearing lock
- POWERPART Threadlock and nutlock
- POWERPART Universal jointing compound
- Engine views
- Engine identification
- Engine lift equipment
- Specifications
- Cylinder head assembly
- Piston and connecting rod assemblies
- Crankshaft assembly
- Timing case and drive assembly
- Cylinder block assembly
- Engine timing
- Aspiration system
- Lubrication system
- Fuel system
- Cooling system
- Flywheel and housing
- Electrical equipment
- Electrical shut off solenoid
- Bus-bar / glowplugs
- Drive belt
- Alternator
- Starter motor
- To remove and to fit Operation 14-5
- Wiring diagram 15 amp alternator - 403C-11
- Wiring diagram 40 amp alternator - 403C-11
- Wiring diagram 55 amp alternator 403C-15, 404C-22 and 404C-22T
- Automatic shutdown connector
- Wiring diagram - automatic shutdown 15 amp alternator - 403C-11
- Wiring diagram - automatic shutdown 40 amp alternator - 403C-11
- Wiring diagram - automatic shutdown 55 amp alternator 403C-15, 404C-22 and 404C-22T
- Auxiliary equipment
- Special tools
Workshop Manual, TPD 1458E, issue 3 - Perkins Confidential: Green 51
6
400 Series
Timing case and drive assembly 6
Timing cover
To remove Operation 6-1
Cautions:
l If the timing case assembly or internal governor components are replaced the fuel adjustment screw should
not be adjusted. The maximum no load speed should be checked after assembly.
l The fuel injection pump, see Operation 11-3 and the keyway in the crankshaft must be removed before the
timing case is removed.
l Ensure that the stop lever arm (1) is held clockwise in tension for removal and assembly.
Note: If the timing case is renewed, a new emission label must be fitted as shown (2).
1 To remove the PTO cover, see Operation 6-9.
2 To remove and to fit the crankshaft pulley, see Operation 5-1.
Engine Special tools
Description Part number
403C-11 Front oil seal protector 21825620
403C-15, 404C-22 and 404C-22T Front oil seal protector 21825621
H1068
1
3
2