Workshop Manual
Table Of Contents
- Perkins 400 Series
- 1 General information
- 2 Specifications
- 3 Cylinder head assembly
- 4 Piston and connecting rod assemblies
- 5 Crankshaft assembly
- 6 Timing case and drive assembly
- 7 Cylinder block assembly
- 8 Engine timing
- 9 Aspiration system
- 10 Lubrication system
- 11 Fuel system
- 12 Cooling system
- 13 Flywheel and housing
- 14 Electrical equipment
- Wiring diagram 15 amp alternator - 403C-11 108
- Wiring diagram 40 amp alternator - 403C-11 109
- Wiring diagram 55 amp alternator 403C-15, 404C-22 and 404C-22T 110
- Automatic shutdown connector 111
- Wiring diagram - automatic shutdown 15 amp alternator - 403C-11 112
- Wiring diagram - automatic shutdown 40 amp alternator - 403C-11 113
- Wiring diagram - automatic shutdown 55 amp alternator 403C-15, 404C-22 and 404C-22T 114
- 15 Auxiliary equipment
- 16 Special tools
- General information
- Introduction
- Safety precautions
- POWERPART recommended consumable products
- POWERPART Antifreeze
- POWERPART Easy Flush
- POWERPART Gasket and flange sealant
- POWERPART Gasket remover
- POWERPART Griptite
- POWERPART Hydraulic threadseal
- POWERPART Industrial grade super glue
- POWERPART Lay-Up 1
- POWERPART Lay-Up 2
- POWERPART Lay-Up 3
- POWERPART Metal repair putty
- POWERPART Pipe sealant and sealant primer
- POWERPART Radiator stop leak
- POWERPART Retainer (high strength)
- POWERPART Safety cleaner
- POWERPART Silicone adhesive
- POWERPART Silicone RTV sealing and jointing compound
- POWERPART Stud and bearing lock
- POWERPART Threadlock and nutlock
- POWERPART Universal jointing compound
- Engine views
- Engine identification
- Engine lift equipment
- Specifications
- Cylinder head assembly
- Piston and connecting rod assemblies
- Crankshaft assembly
- Timing case and drive assembly
- Cylinder block assembly
- Engine timing
- Aspiration system
- Lubrication system
- Fuel system
- Cooling system
- Flywheel and housing
- Electrical equipment
- Electrical shut off solenoid
- Bus-bar / glowplugs
- Drive belt
- Alternator
- Starter motor
- To remove and to fit Operation 14-5
- Wiring diagram 15 amp alternator - 403C-11
- Wiring diagram 40 amp alternator - 403C-11
- Wiring diagram 55 amp alternator 403C-15, 404C-22 and 404C-22T
- Automatic shutdown connector
- Wiring diagram - automatic shutdown 15 amp alternator - 403C-11
- Wiring diagram - automatic shutdown 40 amp alternator - 403C-11
- Wiring diagram - automatic shutdown 55 amp alternator 403C-15, 404C-22 and 404C-22T
- Auxiliary equipment
- Special tools
Workshop Manual, TPD 1458E, issue 3 - Perkins Confidential: Green 85
11
400 Series
Fuel system 11
Atomisers
To remove and to fit Operation 11-1
Cautions:
l Use only deep sockets for this operation.
l Connections should be blanked off until assembly.
l Washer (1) has two small holes 180° apart.
l Discard old washer (2), on assembly fit new nozzle washer.
Note: If the atomisers or injection pipes are replaced it is essential that the fuel adjustment screw is not altered
from the original settings. The maximum no load speed must be checked after assembly.
Continued
Engine Torque Nm (lbf ft) kgf m Test pressure kgf/cm² (lbf/in²) ats
All models
Atomiser 64 (47) 6,5 150 (2133) 145
Atomiser high-pressure pipes 23 (16.9) 2,3
Nut - leak off-rail 27 (19.9) 2,7
H1098/1
1
2
3