Workshop Manual
Table Of Contents
- Perkins 400 Series
- 1 General information
- 2 Specifications
- 3 Cylinder head assembly
- 4 Piston and connecting rod assemblies
- 5 Crankshaft assembly
- 6 Timing case and drive assembly
- 7 Cylinder block assembly
- 8 Engine timing
- 9 Aspiration system
- 10 Lubrication system
- 11 Fuel system
- 12 Cooling system
- 13 Flywheel and housing
- 14 Electrical equipment
- Wiring diagram 15 amp alternator - 403C-11 108
- Wiring diagram 40 amp alternator - 403C-11 109
- Wiring diagram 55 amp alternator 403C-15, 404C-22 and 404C-22T 110
- Automatic shutdown connector 111
- Wiring diagram - automatic shutdown 15 amp alternator - 403C-11 112
- Wiring diagram - automatic shutdown 40 amp alternator - 403C-11 113
- Wiring diagram - automatic shutdown 55 amp alternator 403C-15, 404C-22 and 404C-22T 114
- 15 Auxiliary equipment
- 16 Special tools
- General information
- Introduction
- Safety precautions
- POWERPART recommended consumable products
- POWERPART Antifreeze
- POWERPART Easy Flush
- POWERPART Gasket and flange sealant
- POWERPART Gasket remover
- POWERPART Griptite
- POWERPART Hydraulic threadseal
- POWERPART Industrial grade super glue
- POWERPART Lay-Up 1
- POWERPART Lay-Up 2
- POWERPART Lay-Up 3
- POWERPART Metal repair putty
- POWERPART Pipe sealant and sealant primer
- POWERPART Radiator stop leak
- POWERPART Retainer (high strength)
- POWERPART Safety cleaner
- POWERPART Silicone adhesive
- POWERPART Silicone RTV sealing and jointing compound
- POWERPART Stud and bearing lock
- POWERPART Threadlock and nutlock
- POWERPART Universal jointing compound
- Engine views
- Engine identification
- Engine lift equipment
- Specifications
- Cylinder head assembly
- Piston and connecting rod assemblies
- Crankshaft assembly
- Timing case and drive assembly
- Cylinder block assembly
- Engine timing
- Aspiration system
- Lubrication system
- Fuel system
- Cooling system
- Flywheel and housing
- Electrical equipment
- Electrical shut off solenoid
- Bus-bar / glowplugs
- Drive belt
- Alternator
- Starter motor
- To remove and to fit Operation 14-5
- Wiring diagram 15 amp alternator - 403C-11
- Wiring diagram 40 amp alternator - 403C-11
- Wiring diagram 55 amp alternator 403C-15, 404C-22 and 404C-22T
- Automatic shutdown connector
- Wiring diagram - automatic shutdown 15 amp alternator - 403C-11
- Wiring diagram - automatic shutdown 40 amp alternator - 403C-11
- Wiring diagram - automatic shutdown 55 amp alternator 403C-15, 404C-22 and 404C-22T
- Auxiliary equipment
- Special tools
11
88 Workshop Manual, TPD 1458E, issue 3 - Perkins Confidential: Green
400 Series
Fuel injection pump
To remove and to fit Operation 11-3
Caution: Connections should be blanked off until assembly.
Notes:
l If the fuel injection pump is renewed, shims of the same thickness as originally fitted should be used.
l If a new fuel injection pump is fitted, it should be replaced with a fuel pump with the same part number as
originally fitted.
l When the fuel injection pump is replaced it is essential that the fuel adjustment screw is not altered from
the original setting. The maximum no load speed should be checked after assembly.
Engine Torque Nm (lbf ft) kgf m
403C-11 Fuel injection pump fasteners 6 (4.4) 0,6
403C-15
404C-22
404C-22T
Fuel injection pump fasteners 15 (11) 1,5
H1100