Manual
TEMPLATE
NOTE ALIGNMENT MARK
ON FIXTURE BASE
AHEAD
RED
GREEN
DRILL 1/4” HOLE
FOR ELECTRIC WIRING
USE #6 PAN OR ROUND
HEAD SCREWS
USE #6 PAN OR
ROUND HEAD
SCREWS
NOTE ALIGNMENT MARK
ON FIXTURE BASE
REFERENCE LINE
Cat. No. 0227 Series Bi Color Lights
The above lights are designed for use on power driven vessels
under 20 meters (65.6 ft.) in length operating on a nominal 12 volt
or 24 volt system. In order to comply with ‘72 COLREGS and the
U.S. Inland Rules, the following must be adhered to:
MOUNTING INFORMATION
Read all instructions before proceeding
1). For proper light selection, positioning and configuration, refer to the A.B.Y.C. Standard
A-16*, the ‘72 COLREGS* and the U.S. Inland Rules*. These lights are supplied com-
plete with 12 volt bulb (Cat No. 0071DP0CLR 12V, 10W), however, 24 volt bulbs
(0072DP1CLR) are available for 24 volt systems. Note: PERKO Series 0227 Bi-Color
lights used with a 24V Bulb (Cat. No. 0072DP1CLR) are not certified
in accordance with
33 CFR 183.810 as these lights are intended for replacement use only
on appropriate
vessels constructed prior to 11/1/03. All previous certifications apply. Contact PERKO for
24V applications on new installations.
2). These lights are designed to be mounted on a horizontal surface.
3). Draw a 6 inch long reference line through the center of the selected mounting loca-
tion and parallel to the centerline of the boat.
4). Cut out the mounting template. Place it on the mounting surface such that the ref-
erence line (drawn above) is directly underneath the reference line marked on the
template.
5). Drill 2 holes through the template to accommodate #6 pan or round head mounting
screws. Drill a 1/4 inch hole to accommodate the electric wiring.
6). Attach supply connections to the light, making sure to wire in accordance with both
A.B.Y.C. Standard E-9* and U.S. Coast Guard Safety Standards for Boat Electrical
Systems (33 CFR 183)*.
7). Mount the light in accordance with the template. Note that there are thin reference
marks around the outside of the base that must be aligned with the reference line
(drawn in Step #3) for final accuracy of mounting orientation.
8). To Re-Bulb: Remove two mounting screws and lift light off deck. While upside-
down, use a small bladed screwdriver (in either of the two slots) to pry out the bulb
holder. Replace bulb and snap back into place. Re-mount light.
* The above referenced Standards can be obtained from:
1) American Boat & Yacht Council, Inc 2) U.S. Coast Guard
613 Third Street, Suite 10 Washington D.C. 20593
Annapolis, MD 21403 (or your local C.G. office)
PERKO, Inc.
16490 N.W. 13th Avenue
12/08 Miami, Florida 33169-5707
0227INS1 www.perko.com
12V USCG
APPROVAL
33 CFR 183.810
Visibility: 2nm
Tested By: IMANNA Labs.
Date: 5/16/03
Meets ABYC A-16
TEMPLATE
NOTE ALIGNMENT MARK
ON FIXTURE BASE
AHEAD
RED
GREEN
DRILL 1/4” HOLE
FOR
ELECTRIC WIRING
USE #6 PAN OR ROUND
HEAD SCREWS
USE #6 PAN OR
ROUND HEAD
SCREWS
NOTE ALIGNMENT MARK
ON FIXTURE BASE
REFERENCE LINE
Cat. No. 0227 Series Bi Color Lights
The above lights are designed for use on power driven vessels
under 20 meters (65.6 ft.) in length operating on a nominal 12 volt
or 24 volt system. In order to comply with ‘72 COLREGS and the
U.S. Inland Rules, the following must be adhered to:
MOUNTING INFORMATION
Read all instructions before proceeding
1). For proper light selection, positioning and configuration, refer to the A.B.Y.C. Standard
A-16*, the ‘72 COLREGS* and the U.S. Inland Rules*. These lights are supplied com-
plete with 12 volt bulb (Cat No. 0071DP0CLR 12V, 10W), however, 24 volt bulbs
(0072DP1CLR) are available for 24 volt systems. Note: PERKO Series 0227 Bi-Color
lights used with a 24V Bulb (Cat. No. 0072DP1CLR) are not certified
in accordance with
33 CFR 183.810 as these lights are intended for replacement use only
on appropriate
vessels constructed prior to 11/1/03. All previous certifications apply. Contact PERKO for
24V applications on new installations.
2). These lights are designed to be mounted on a horizontal surface.
3). Draw a 6 inch long reference line through the center of the selected mounting loca-
tion and parallel to the centerline of the boat.
4). Cut out the mounting template. Place it on the mounting surface such that the ref-
erence line (drawn above) is directly underneath the reference line marked on the
template.
5). Drill 2 holes through the template to accommodate #6 pan or round head mounting
screws. Drill a 1/4 inch hole to accommodate the electric wiring.
6). Attach supply connections to the light, making sure to wire in accordance with both
A.B.Y.C. Standard E-9* and U.S. Coast Guard Safety Standards for Boat Electrical
Systems (33 CFR 183)*.
7). Mount the light in accordance with the template. Note that there are thin reference
marks around the outside of the base that must be aligned with the reference line
(drawn in Step #3) for final accuracy of mounting orientation.
8). To Re-Bulb: Remove two mounting screws and lift light off deck. While upside-
down, use a small bladed screwdriver (in either of the two slots) to pry out the bulb
holder. Replace bulb and snap back into place. Re-mount light.
* The above referenced Standards can be obtained from:
1) American Boat & Yacht Council, Inc 2) U.S. Coast Guard
613 Third Street, Suite 10 Washington D.C. 20593
Annapolis, MD 21403 (or your local C.G. office)
PERKO, Inc.
16490 N.W. 13th Avenue
12/08 Miami, Florida 33169-5707
0227INS1 www.perko.com
12V USCG
APPROVAL
33 CFR 183.810
Visibility: 2nm
Tested By: IMANNA Labs.
Date: 5/16/03
Meets ABYC A-16