Perle Gigabit Fiber to Fiber Media Converters Installation Guide S-1000MM-XXXXXX P/N 5500314-11
Overview This document contains instructions necessary for the installation and operation of the Perle Gigabit Standalone Fiber to Fiber Media Converters (S-1000MM). These products allow dissimilar 1000Base-X fiber interfaces to connect to one another.
Fiber port 2 – MM2/SM2 Model Connector Mode Distance S-1000MM-S1SC120U SC SM 120 km/74.6 mi. Wavelength (TX/RX) 1510/1590 nm S-1000MM-S1SC120D SC SM 120 km/74.6 mi. 1590/1510 nm Visit Perle’s web site for the most up to date Installation guides, models and specifications: http://www.perle.com/ Installation The default switch setting (all switches in the UP position) will work for most installations.
Fiber Negotiation (Switch 1) Switch Position Mode Up (default) Auto Down Off Auto: In this mode of operation the media converter will negotiate fiber parameters on both MM1 and MM2/SM2 (fiber ports). This will ensure the most optimal connection parameters will be in effect. If connecting to another Perle Media Converter, this parameter should be set to Auto. Off: Fiber negotiation on both fiber ports will be disabled.
Fiber Fault Alert (Switch 3) Switch Position Mode Up (default) Enabled Down Disabled Enabled: If the media converter detects a loss of fiber signal on the fiber receiver, it will immediately disable its fiber transmitter signal on this port. This, in effect, notifies the fiber link partner that an error condition exists on the fiber connection.
Sequence of Events 1. Media Converter A loses fiber connection (RX) on MM2/SM2. 2. Media Converter A disables the transmitter (TX) MM2/SM2. 3. Media Converter B detects loss of fiber link on receiver RX – MM2/SM2. 4. Media Converter B turns off transmitter (TX) on MM1. 5. Media Converter A MM1 is not affected Remote Loopback Fiber 1 (Switch 4) Switch Position Mode Up (default) Disabled Down Enabled Disabled: The loopback feature is disabled. This is the normal position for regular operation.
Installing the Duplex Fiber Cable 1. Locate a 1000Base-X compliant duplex (2 strands) fiber cable with male connections. 2. Connect the fiber cables from one media converter to the other media converter/switch/fiber device ensuring that the RX and TX are reversed at the opposite end. Installing the Simplex Fiber Cable 1. Locate a 1000Base-X compliant simplex (1 strand) fiber cable with male connections. 2. Connect the fiber cable from one media converter to the other media converter/switch/fiber device.
Operation Status LED The Perle Gigabit Fiber to Fiber Media converters have three single colored status LEDs located on the front panel of the unit. PWR - Power/Test • On: Power is on and the unit is in normal operation mode. • Blinking slowly: the unit is in loopback mode. • Blinking quickly: the unit has a hardware error. LK1 – MM1 (Fiber Link) Activity • On: Fiber link present. • Blinking slowly: The fiber link has been taken down as a result of Smart Link Pass-Through.
Troubleshooting General • Ensure power is supplied to the media converter – use of the Perle supplied power adapter is highly recommended. • Ensure both devices on either end of the fiber are compatible. If using a single fiber connection, ensure that you have both an Upstream (U) and Downstream (D) media converter. • Ensure all cabling is of the correct type and is in good operating condition.
Technical Specifications The following applies to all S-1000MM media converters: Power Input/Consumption Operating Temperature: Storage Temperature: Operating Humidity: Storage Humidity: Operating Altitude: Weight: MTBF: (with power supply) 12V DC /2.5 W 0°C - 50°C (32°F - 122°F) -25°C - 70°C (-13°F - 158°F) 5% to 90% non-condensing 5% to 95% non-condensing Up to 3,048 m (10,000 ft) 0.3 kg (0.
Model Mode Wavelength (nm) TX Power (dB) RX Power (dB) Budget (dB) S-1000MM-S1SC10U SM TX: 1310 RX:1490 Min: -9 Max: -3 Min: -20 Max: -3 11 S-1000MM-S1SC10D SM TX:1490 RX:1310 Min: -9 Max: -3 Min: -20 Max: -3 11 S-1000MM-S1SC20U SM TX: 1310 RX:1490 Min: -8 Max: -3 Min: -22 Max: -3 14 S-1000MM-S1SC20D SM TX:1490 RX:1310 Min: -8 Max: -3 Min: -22 Max: -3 14 S-1000MM-S1SC40U SM TX: 1310 RX:1490 Min: -3 Max: 2 Min: -23 Max: -3 20 S-1000MM-S1SC40D SM TX:1490 RX:1310 Min: -3
Compliance Information FCC This product has been found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions in this Guide, may cause harmful interference to radio communications.
