UNDERCOUNTER INSTALLATION INSTRUCTIONS PERLICK RESIDENTIAL UNDERCOUNTER REFRIGERATION To prevent appliance damage or injury, read these instructions thoroughly prior to installation. HP15 HP24 HP48 HH24 HC24 HA24 15” SIGNATURE SERIES 24” SIGNATURE SERIES 48" SIGNATURE SERIES SIGNATURE SERIES SOTTILE C-SERIES ADA-COMPLIANT SERIES Form No. Z2348-F Rev. 05.27.
PERLICK RESIDENTIAL INSTALLATION MANUAL TABLE OF CONTENTS Warranty Information ..................................................................2 Door Information.............................................................................8 Safety Information..........................................................................4 Changing the Door Swing Direction..................................8 Plumbing, Electrical and General Information..............4 Handle Installation......................
PERLICK RESIDENTIAL INSTALLATION MANUAL REMEDY: Perlick will provide the parts and labor necessary to repair or replace (at Perlick’s option) any parts proven to be defective in material or workmanship during the Basic Warranty Period. Perlick will provide the replacement parts, but not the labor, for any parts of the hermetically sealed refrigeration system proven to be defective in materials or workmanship during the Extended Warranty Period.
PERLICK RESIDENTIAL INSTALLATION MANUAL SAFETY PLEASE READ all instructions completely before attempting to install or operate the unit. Take particular note of the DANGER, WARNING and CAUTION information in the manual. The information is important for the safe and efficient installation, operation and care of your Perlick unit. DANGER Indicates a hazard that WILL result in serious injury or death if precautions are not followed.
PERLICK RESIDENTIAL INSTALLATION MANUAL DANGER Serious Electrocution Hazard! Electrical grounding is required. This appliance is equipped with a 3-prong (grounding) polarized plug for your protection against possible shock hazards. Failure to comply with these electrical guidelines may result in possible death or serious injury, fire, or loss of property. • Never remove the round grounding prong from the plug. • Never use a 2-prong adapter. • Never use extension cord to connect power to the unit.
PERLICK RESIDENTIAL INSTALLATION MANUAL PREPARING THE SPACE If the unit is to be installed under CAUTION a countertop, it is recommended that the countertop be supported by surrounding cabinetry and use shims to support countertop directly above the refrigerated cabinet. CAUTION Make sure the floor under the unit is level with the surrounding finished floor. Protect a finished floor with plywood, cardboard, or some other suitable material before moving the unit into place.
PERLICK RESIDENTIAL INSTALLATION MANUAL TOE PLATE INSTALLATION Once the unit is secured in place, install the louvered toe plate. Secure the plate by snapping the latch into the latch catch on the unit (Figure 5). CAUTION The toe plate must be removed to service the unit. The floor cannot interfere with removal, and the louvered sections must not be covered or obstructed. Obstructions could prevent proper air circulation, which may damage the unit.
PERLICK RESIDENTIAL INSTALLATION MANUAL SHELVING/DRAWER ADJUSTMENTS CAUTION Completely empty shelf or drawer before removing. 1. Pull the shelf/drawer out to its furthest position. Locate the tabs in the middle of both extenders. Lift one tab up while pushing the opposite tab down, and pull shelf/ drawer out (Figure 6). 2. Position each bracket separately. Grasp the middle of the bracket, pull the front end up and out, then forward to remove it. 3. Place bracket at desired location.
PERLICK RESIDENTIAL INSTALLATION MANUAL 5). Using the screws removed in step 3, install the top and bottom hinge brackets from the kit (Fig. 9). Figure 7. Door Removal Figure 9. Hinge Installation 6). Remove the top and bottom door hinge brackets and the push plunger brackets (Fig. 10). Retain the screws for later use. Figure 10. Door Brackets Figure 8.
PERLICK RESIDENTIAL INSTALLATION MANUAL 7). Remove the front panel from the door assembly by removing the door gasket and then removing the overlay mounting screws, 4 per side, from the perimeter of the door assembly (Fig. 11). Rotate the front panel 180°. The top becomes the bottom. Reattach using the same screws and mounting holes and then reinstall the door gasket. 9). Insert the bearing into the door hinge bracket (Fig. 13). 10).
PERLICK RESIDENTIAL INSTALLATION MANUAL 12). Place the lower V-block into the lower cabinet hinge with the notch parallel to the cabinet (Fig. 15). HANDLE INSTALLATION The handle mounting on the wood CAUTION overlay should be mounted on the overlay only (not the actual door) to avoid damage to the factory door. 1. Handle must be attached to the overlay before mounting the overlay onto the door. Mark the rear of the wood overlay panel with handle fastening locations. 2.
PERLICK RESIDENTIAL INSTALLATION MANUAL WOOD OVERLAY INSTALLATION (FOR -2, -4 AND -6 MODELS) Before beginning installation, check all components for proper fit and finish. Handle should be installed to the overlay prior to installing overlay to door (use countersunk flathead fasteners for handle installation.) 3. In some cases, the dart on the gasket may rip. If this happens, replace with a new gasket. CAUTION For best performance and functionality, the overlay panels should be 3/4” thick.
PERLICK RESIDENTIAL INSTALLATION MANUAL 5. Loosely attached the four corners of the overlay panel with the door frame with #10 x 3/4” wood screws. 7. After alignment is satisfied, fasten down all screws through the screw holes. CAUTION Do not overtighten wood overlay 6. Make sure the overlay panel is aligned properly with the door. attachment screws, as this may damage the factory supplied door frame. 8. When re-installing the gasket, make sure the dart is pressed inside the slot on the door frame.
PERLICK RESIDENTIAL INSTALLATION MANUAL 9. Verify that the gasket is fully seated onto the door frame when completed. WINE RACK TRIM (OPTIONAL) All wine reserve racks come with sleek stainless steel fronts. Unfinished solid hardwood fronts are optional and can be removed and replaced with other wood to match your cabinetry. See Figure 18 and 19 for wine rack face details. NOTE: The unfinished faces should be finished and sealed.
PERLICK RESIDENTIAL INSTALLATION MANUAL NOTES perlick customer service (800)558-5592 | 15
Perlick Residential is a division of Perlick Corporation © 2018 Perlick Corporation 8300 West Good Hope Road, Milwaukee, WI 53223, USA perlick.com/residential • (800) 558-5592 Form No. Z2348-F Rev. 05.27.
