UNDERCOUNTER INSTALLATION INSTRUCTIONS C US R600a Refrigerant PERLICK RESIDENTIAL UNDERCOUNTER REFRIGERATION To prevent appliance damage or injury, read these instructions thoroughly prior to installation. HP15 HP24 HH24 HC24 HA24 15” SIGNATURE SERIES 24” SIGNATURE SERIES SIGNATURE SERIES SHALLOW DEPTH C-SERIES ADA-COMPLIANT SERIES Form No. Z2667-A Rev. 12.15.
PERLICK RESIDENTIAL UNDERCOUNTER INSTALLATION MANUAL GENERAL INFORMATION Introduction Warranty Congratulations on your purchase of a Perlick Residential undercounter product. This manual has been prepared to assist you in the installation of your cabinet and to acquaint you with its operation and maintenance. To register your product, visit our web site at www.perlick. com. Click on “Residential”, then “Resources”. Click on the link “Warranty Registration Form”.
PERLICK RESIDENTIAL UNDERCOUNTER INSTALLATION MANUAL SAFETY PLEASE READ all instructions completely before attempting to install or operate the unit. Take particular note of the DANGER, WARNING and CAUTION information in the manual. The information is important for the safe and efficient installation, operation and care of your Perlick unit. Indicates a hazard that WILL result in serious injury or death if precautions are not followed.
PERLICK RESIDENTIAL UNDERCOUNTER INSTALLATION MANUAL Preparing the Cabinet for Use UNCRATING AND INSPECTION Remove all crating material before operating. Carefully inspect cabinet for hidden damage. If damage is discovered, file your claim immediately with the transport company. Perlick is not responsible for damage in transit. Do not use or store flammable liquids (ie; gasoline) or vapors near the appliance to avoid fire.
PERLICK RESIDENTIAL UNDERCOUNTER INSTALLATION MANUAL REPAIR & MAINTENANCE All service work shall be performed Perlick-authorized service personnel. All component parts shall be replaced with like components. Incorrect parts or improper service may result in fire. WARNING by INSTALLING CASTERS OR LEGS (OPTIONAL) Attach bracket assembly to the bottom of the cabinet base using the ¼”-20 Philips head machine screws provided.
PERLICK RESIDENTIAL UNDERCOUNTER INSTALLATION MANUAL PREPARING THE SPACE If the unit is to be installed under CAUTION a countertop, it is recommended that the countertop be supported by surrounding cabinetry and use shims to support countertop directly above the refrigerated cabinet. Make sure the floor under the CAUTION unit is level with the surrounding finished floor. Protect a finished floor with plywood, cardboard, or some other suitable material before moving the unit into place.
PERLICK RESIDENTIAL UNDERCOUNTER INSTALLATION MANUAL TOE PLATE INSTALLATION Once the unit is secured in place, install the louvered toe plate. Secure the plate by snapping the latch into the latch catch on the unit , and re-attach screws using through holes provided in the toe kick. A phillips #2 screwdriver, with a 3” long shaft will be required. (Figure 5). CAUTION The toe plate must be removed to service the unit.
PERLICK RESIDENTIAL UNDERCOUNTER INSTALLATION MANUAL SHELVING/DRAWER ADJUSTMENTS CAUTION Completely empty shelf or drawer before removing. 1. Pull the shelf/drawer out to its furthest position. Locate the tabs in the middle of both extenders. Lift one tab up while pushing the opposite tab down, and pull shelf/drawer out (Figure 6). 2. Position each bracket separately. Grasp the middle of the bracket, pull the front end up and out, then forward to remove it. 3. Place bracket at desired location.
PERLICK RESIDENTIAL UNDERCOUNTER INSTALLATION MANUAL 5) Using the screws removed in step 3, install the top and bottom hinge brackets from the kit (Fig. 9). Figure 7. Door Removal Figure 9. Hinge Installation 6) Remove the top and bottom door hinge brackets and the push plunger brackets (Fig. 10). Retain the screws for later use. Figure 10. Door Brackets Figure 8.
PERLICK RESIDENTIAL UNDERCOUNTER INSTALLATION MANUAL 7) Remove the front panel from the door assembly by removing the door gasket and then removing the overlay mounting screws, 4 per side, from the perimeter of the door assembly (Fig. 11). Rotate the front panel 180°. The top becomes the bottom. Reattach using the same screws and mounting holes and then reinstall the door gasket. 9) Insert the bearing into the door hinge bracket (Fig. 13). 10).
PERLICK RESIDENTIAL UNDERCOUNTER INSTALLATION MANUAL 12) Place the lower V-block into the lower cabinet hinge with the notch parallel to the cabinet (Fig. 15). Figure 15. Installing V-Block 13) Lift the door assembly and insert the top pin into the bearing. Move door toward cabinet and align the V-blocks (Fig. 16). HANDLE INSTALLATION The handle mounting on the wood CAUTION overlay should be mounted on the overlay only (not the actual door) to avoid damage to the factory door. 1.
PERLICK RESIDENTIAL UNDERCOUNTER INSTALLATION MANUAL WOOD OVERLAY INSTALLATION Before beginning installation, check all components for proper fit and finish. Handle should be installed to the overlay prior to installing overlay to door (use countersunk flathead fasteners for handle installation.) 3. In some cases, the dart on the gasket may rip. If this happens, replace with a new gasket. CAUTION For best performance and functionality, the overlay panels should be 3/4” thick.
PERLICK RESIDENTIAL UNDERCOUNTER INSTALLATION MANUAL 5. Loosely attached the four corners of the overlay panel with the door frame with #10 x 3/4” wood screws. 7. After alignment is satisfied, fasten down all screws through the screw holes. CAUTION Do not overtighten wood overlay 6. Make sure the overlay panel is aligned properly with the door. attachment screws, as this may damage the factory supplied door frame. 8.
PERLICK RESIDENTIAL UNDERCOUNTER INSTALLATION MANUAL 9. Verify that the gasket is fully seated onto the door frame when completed. WINE RACK TRIM (OPTIONAL) All wine reserve racks come with sleek stainless steel fronts. Unfinished solid hardwood fronts are optional and can be removed and replaced with other wood to match your cabinetry. See Figure 18 and 19 for wine rack face details. NOTE: The unfinished faces should be finished and sealed.
PERLICK RESIDENTIAL UNDERCOUNTER INSTALLATION MANUAL TOUCH-SCREEN CONTROL OPERATION OPERATION Programming Button Definitions: MASTER SWITCH Signature Series products come equipped with a master power switch located behind the louvered toe kick. Remove the toe kick to turn power on or off to the unit. To remove the toe kick. Remove the two screws located in the through holes on the edge of the toe kick, near the latch strikes.
PERLICK RESIDENTIAL UNDERCOUNTER INSTALLATION MANUAL NOTE: Dependent on the model and configuration, the controllers have been programmed to only allow a lower compartment temperature adjustment range as specified within the chart below. The upper compartment range is not limited, but should always be kept within the specified range shown in the table for the upper compartment. See the chart below for the specified range allowed for your unit.
PERLICK RESIDENTIAL UNDERCOUNTER INSTALLATION MANUAL NOTES Perlick customer service (800)558-5592 | 17
Perlick Residential is a division of Perlick Corporation © 2020 Perlick Corporation 8300 West Good Hope Road, Milwaukee, WI 53223, USA perlick.com/residential • (800) 558-5592 Form No. Z2667-A Rev. 12.15.
